Response of fiber Bragg gratings bonded on a glass/epoxy laminate subjected to static loadings

Fiber Bragg gratings (FBG) may be used to monitor strain over the surface of a structure as an alternative technology to conventional strain gauges. However, FBG bonding techniques have still not been established to yield satisfactory surface measurements. Here, two adhesives were investigated, one with low viscosity and the other with high viscosity for bonding FBGs on glass/epoxy sandwich skins. First, instrumented elementary specimens were tested under tension. FBG strain results were analyzed together with digital image correlation (DIC) measurements. The influence of the bonding layer on the measured strain and on the integrity of the sensor was investigated by considering different regions of interest. Next, an instrumented structural sandwich beam was tested under four-point bending. FBG rosettes were compared to conventional strain gauge rosettes. The high viscosity adhesive demonstrated behaviors that affected FBG accuracy. Brittleness of the bonding layer and poor interface adhesion were observed using DIC and X-ray tomography. By contrast, the low viscosity adhesive demonstrated satisfactory results. The FBG strain measurements appeared to be consistent with those of DIC. The accuracy is also adequate as the FBGs and the conventional strain gauges had similar results in three directions, under tension and under compression.

[1]  F. Ansari,et al.  MECHANICS OF BOND AND INTERFACE SHEAR TRANSFER IN OPTICAL FIBER SENSORS , 1998 .

[2]  N. Djilali,et al.  In-fibre Bragg grating sensors for distributed temperature measurement in a polymer electrolyte membrane fuel cell , 2009 .

[3]  K. Hill,et al.  Fiber Bragg grating technology fundamentals and overview , 1997 .

[4]  Eric Udd,et al.  Multidimensional strain field measurements using fiber optic grating sensors , 2000, Smart Structures.

[5]  Wei Zhang,et al.  Effects of bonding layer on the available strain measuring range of fiber Bragg gratings. , 2014, Applied optics.

[6]  Daniel Betz,et al.  Structural Monitoring Using Fiber-Optic Bragg Grating Sensors , 2003 .

[7]  Christopher K.Y. Leung,et al.  Investigation of the strain transfer for surface-attached optical fiber strain sensors , 2008 .

[8]  J. A. Guemes,et al.  Response of Bragg grating fiber-optic sensors when embedded in composite laminates , 2002 .

[9]  Philippe Olivier,et al.  Assessment of cure residual strains through the thickness of carbon–epoxy laminates using FBGs, Part I: Elementary specimen , 2009 .

[10]  K. Peters,et al.  Embedded optical fiber Bragg grating sensor in a nonuniform strain field: Measurements and simulations , 2001 .

[11]  John Botsis,et al.  Characterization of residual strains in an epoxy block using an embedded FBG sensor and the OLCR technique , 2006 .

[12]  Hwa-Yaw Tam,et al.  Fundamentals and applications of optical fiber Bragg grating sensors to textile structural composites , 1998 .

[13]  Raymond M. Measures,et al.  The mechanical load transfer into a distributed optical fiber sensor due to a linear strain gradient: embedded and surface bonded cases , 1999 .

[14]  Tadahito Mizutani,et al.  Effect of thermal residual stress on the reflection spectrum from FBG sensors embedded in CFRP composites , 2002, SPIE Smart Structures and Materials + Nondestructive Evaluation and Health Monitoring.

[15]  Antonello Cutolo,et al.  In-situ measurement of thermoset resin degree of cure using embedded fiber optic , 1999, Optics East.

[16]  Thomas Gmür,et al.  Residual strain development in an AS4/PPS thermoplastic composite measured using fibre Bragg grating sensors , 2006 .

[17]  Y.M. Chang,et al.  An investigation of bonding-layer characteristics of substrate-bonded fiber Bragg grating , 2005, Journal of Lightwave Technology.

[18]  Bing Pan,et al.  High-Accuracy 2D Digital Image Correlation Measurements with Bilateral Telecentric Lenses: Error Analysis and Experimental Verification , 2013 .

[19]  Quanbao Wang,et al.  Strain transfer of surface-bonded fiber Bragg grating sensors for airship envelope structural health monitoring , 2012 .

[20]  F. Bosia,et al.  Through-the-thickness distribution of strains in laminated composite plates subjected to bending , 2004 .

[21]  Israel Herszberg,et al.  Structural integrity analysis of embedded optical fibres in composite structures , 1999 .

[22]  Yu-Lung Lo,et al.  Investigation of strain transmission of surface-bonded FBGs used as strain sensors , 2009 .