Dimensional measurement of micro-moulded parts by computed tomography

Computed tomography (CT) is progressively assuming an important role in metrology applications and great efforts are being made in order to turn it into a reliable and standardized measuring technology. CT is typically used for non-destructive tests, but it is currently becoming very popular for dimensional metrology applications due to its strategic advantages such as the capability of performing measurements on both the component's surface and volume, allowing inspection possibilities to otherwise non-accessible internal features. This paper focuses on the dimensional verification of two micro-injection moulded components, selected from actual industrial productions, using CT metrological tools. For this purpose, several parts have been measured with two different CT machines, and the results have been compared with the measurements obtained by other measuring systems. The experimental work carried out and the analysis of the results provide valuable conclusions about the advantages and drawbacks of using CT metrology in comparison with other measuring systems when these techniques are employed for the quality control of micro-moulded parts.

[1]  Pavel Müller,et al.  Verification of a CT scanner using a miniature step gauge , 2011 .

[2]  S. Carmignato,et al.  Accuracy of industrial computed tomography measurements: Experimental results from an international comparison , 2012 .

[3]  Frank Welkenhuyzen,et al.  A test object with parallel grooves for calibration and accuracy assessment of industrial computed tomography (CT) metrology , 2011 .

[4]  Enrico Savio,et al.  Traceable volume measurements using coordinate measuring systems , 2011 .

[5]  W. Knapp,et al.  Tolerance And Uncertainty , 1970 .

[6]  Wim Dewulf,et al.  Industrial computer tomography for dimensional metrology: Overview of influence factors and improvement strategies , 2009 .

[7]  Hans Nørgaard Hansen,et al.  Applications of dimensional micro metrology to the product and process quality control in manufacturing of precision polymer micro components , 2009 .

[8]  Christof Reinhart,et al.  INDUSTRIAL COMPUTER TOMOGRAPHY - A UNIVERSAL INSPECTION TOOL , 2008 .

[9]  Petru Berce,et al.  Geometrical metrology on silicone rubber by computed tomography , 2011 .

[10]  Robert Schmitt,et al.  Computed tomography for dimensional metrology , 2011 .

[11]  L. Mancini,et al.  Testing of x-ray microtomography systems using a traceable geometrical standard , 2009 .

[12]  Frank Härtig,et al.  Measurement of micro gears: comparison of optical, tactile-optical, and CT measurements , 2011, Electronic Imaging.

[13]  Alex Attridge,et al.  Analysis of the effect of cone-beam geometry and test object configuration on the measurement accuracy of a computed tomography scanner used for dimensional measurement , 2011 .

[14]  Jochen Hiller,et al.  Artefaktkorrekturen beim dimensionellen Messen mit industrieller Röntgen-ComputertomographieArtefact Correction at Coordinate Measuring with Industrial X-Ray Computed Tomography , 2009 .

[15]  Karin Kniel,et al.  Achieving Traceability of Industrial Computed Tomography , 2010 .

[16]  Enrico Savio,et al.  Metrological performance of optical coordinate measuring machines under industrial conditions , 2010 .

[17]  Roger Frost,et al.  International Organization for Standardization (ISO) , 2004 .

[18]  Robert Schmitt,et al.  Uncertainty in measurement for x-ray-computed tomography using calibrated work pieces , 2010 .

[19]  F E Merrill,et al.  Charged particle radiography , 2013, Reports on progress in physics. Physical Society.

[20]  Markus Bartscher,et al.  Enhancement and Proof of Accuracy of Industrial Computed Tomography (CT) Measurements , 2007 .

[21]  Enrico Savio,et al.  Coordinate metrology using scanning probe microscopes , 2009 .

[22]  Wim Dewulf,et al.  A test object with parallel grooves for calibration and accuracy assessment of industrial CT metrology , 2011 .

[23]  Philipp Krämer,et al.  Predetermination of Measurement Uncertainty in the Application of Computed Tomography , 2013 .

[24]  Uwe Brand,et al.  A micro-CMM with metrology frame for low uncertainty measurements , 2005 .

[25]  Junyan Rong,et al.  Geant4-Based Monte Carlo Simulator for Fan-and Cone-Beam X-ray CT , 2010, 2010 4th International Conference on Bioinformatics and Biomedical Engineering.