Mass-Optimal Design Methodology for DC-DC Converters in Low-Power Portable Fuel Cell Applications

Fuel cell systems have not significantly penetrated the low-power ( W) portable energy source market, largely due to complexity of control and the balance-of-plant systems required. Even though the fuel cell and fuel container may scale down well, the pumps, blowers, and power converters required may dominate the system mass. This paper focuses on the tradeoff between efficiency and converter mass, and achieving the design objective of minimum mass of both converter and fuel. The effect of desired run-time, or mission duration, on the optimal dc-dc converter design was explored in detail. The effort focused on boost converters; however, the methodology can be applied to any converter topology. In an example case, at a mission length of 100 h, the optimized converter saved 91 g of system mass when compared to an off-the-shelf dc-dc converter.

[1]  Yuan Yu,et al.  Formulation of a methodology for power circuit design optimization , 1976, 1970 IEEE Power Electronics Specialists Conference.

[2]  William Gerard Hurley,et al.  Optimized transformer design: inclusive of high-frequency effects , 1998 .

[3]  Frede Blaabjerg,et al.  An Advanced Tool for Optimized Design of Power Electronic Circuits , 1998 .

[4]  Jan Abraham Ferreira,et al.  Improved analytical modeling of conductive losses in magnetic components , 1994 .

[5]  P. Enjeti,et al.  Design considerations for a fuel cell powered dc-dc converter for portable applications , 2006, Twenty-First Annual IEEE Applied Power Electronics Conference and Exposition, 2006. APEC '06..

[6]  Yue Fu,et al.  Power MOSFET Switching Loss Analysis: A New Insight , 2006, Conference Record of the 2006 IEEE Industry Applications Conference Forty-First IAS Annual Meeting.

[7]  Chas.P. Steinmetz,et al.  On the law of hysteresis , 1984, Proceedings of the IEEE.

[8]  James Larminie,et al.  Fuel Cell Systems Explained , 2000 .

[9]  Philip T. Krein,et al.  Elements of Power Electronics , 1997 .

[10]  B. Wetton,et al.  Water Management in PEM Fuel Cells , 2004 .

[11]  Larry J. Markoski,et al.  Microfluidic fuel cell based on laminar flow , 2004 .

[12]  Phoivos D. Ziogas,et al.  A novel approach for minimizing high-frequency transformer copper losses , 1988 .

[13]  Yuan Yu,et al.  Power Converter Design Optimization , 1979, IEEE Transactions on Aerospace and Electronic Systems.

[14]  Robert Rodriguez,et al.  DC-to-DC Converter Power-Train Optimization for Maximum Efficiency , 1981, IEEE Transactions on Aerospace and Electronic Systems.

[15]  J Gowar,et al.  Power Semiconductor Devices: Theory and Applications , 1999 .

[16]  S. Sinha.  Methods of nonlinear programming , 2006 .

[17]  Charles R. Sullivan,et al.  An improved calculation of proximity-effect loss in high-frequency windings of round conductors , 2003, IEEE 34th Annual Conference on Power Electronics Specialist, 2003. PESC '03..

[18]  F. C. Lee,et al.  Design optimization for a half-bridge DC-DC converter , 1982, 1980 IEEE Power Electronics Specialists Conference.

[19]  Harry A. Owen,et al.  Parametric study of minimum converter loss in an energy-storage DC-to-DC converter , 1982, 1982 IEEE Power Electronics Specialists conference.

[20]  D. Boroyevich,et al.  Design of a boost power factor correction converter using optimization techniques , 2004, IEEE Transactions on Power Electronics.

[21]  T. Meynard,et al.  Interactions Between Fuel Cells and Power Converters: Influence of Current Harmonics on a Fuel Cell Stack , 2007, IEEE Transactions on Power Electronics.

[22]  W.A. Roshen,et al.  A Practical, Accurate and Very General Core Loss Model for Nonsinusoidal Waveforms , 2005, IEEE Transactions on Power Electronics.

[23]  P. L. Dowell,et al.  Effects of eddy currents in transformer windings , 1966 .

[24]  C. Wu.  Evaluation and implementation of the optimum magnetics design of the cuk converter in comparison to the conventional buck-boost converter , 1982 .

[25]  J. Zhang,et al.  Decoupled optimization technique for design of switching regulators using genetic algorithms , 2000, 2000 IEEE International Symposium on Circuits and Systems. Emerging Technologies for the 21st Century. Proceedings (IEEE Cat No.00CH36353).

[26]  Chen Zhou,et al.  Application of nonlinear design optimization for power converter components , 1990 .

[27]  William Gerard Hurley.  Optimizing core and winding design in high frequency transformers , 1996, V IEEE International Power Electronics Congress Technical Proceedings, CIEP 96.

[28]  F. Blaabjerg,et al.  An advanced tool for optimised design of power electronic circuits , 1998, Conference Record of 1998 IEEE Industry Applications Conference. Thirty-Third IAS Annual Meeting (Cat. No.98CH36242).

[29]  J. Abadie,et al.  The GRG Method for Nonlinear Programming , 1978 .

[30]  Fred C. Lee,et al.  Optimizing design for low voltage DC-DC converters , 1997, Proceedings of APEC 97 - Applied Power Electronics Conference.

[31]  S. D. Sudhoff,et al.  Evolutionary Optimization of Power Electronics Based Power Systems , 2007, APEC 07 - Twenty-Second Annual IEEE Applied Power Electronics Conference and Exposition.

[32]  A. Van den Bossche,et al.  Measurement and loss model of ferrites with non-sinusoidal waveforms , 2004, 2004 IEEE 35th Annual Power Electronics Specialists Conference (IEEE Cat. No.04CH37551).

[33]  R. Petkov,et al.  Optimum design of a high-power, high-frequency transformer , 1996 .

[34]  F. C. Lee,et al.  Nonlinear program based optimization of boost and buck-boost converter designs , 1981, 1981 IEEE Power Electronics Specialists Conference.

[35]  F. C. Lee,et al.  Practical nonlinear design optimization tool for power converter components , 1987, IEEE Power Electronics Specialists Conference.