Influence of environmental temperature on the dynamic properties of a die attached MEMS device

Die attach is one of the major processes that may induce unwanted stresses and deformations into micro-electro-mechanical systems (MEMS). The thermo-elastic coupling between the die and package may affect the performance of MEMS under various temperature loads, causing unreasonable effects of the output signal, such as zero offset, temperature coefficient of offset (TCO), nonlinearity, ununiformity and hysteresis, etc. A complete characterization of these effects is critical for a more reliable design. This work presents experimental studies of the temperature effects on the dynamic properties of MEMS. Microbridges and strain gauges with different dimensions were used as test structures. They were surface-micromachined on test chips and the chips were die attached on organic laminate substrates using epoxy bonding as well as tape adhering. The material and dimension of the substrate were specially defined to amplify the magnitude of the coupled deformation for the convenience of investigation. Modal frequencies of the microbridges under a set of controlled environmental temperature before and after die attach were measured using a laser Doppler vibrometer system. The average initial residual strain was also measured from the strain gauges to help analyze the dynamic behavior. Nonlinear TCO of the frequencies were observed to be as large as 2,500–5,000 ppm for the epoxy-bonded samples, in contrast with much smaller values for the tape-adhered and unpackaged ones. The frequencies recovered to their original values beyond the curing temperature of the epoxy. A distributed feature was also observed in frequencies of the microbridges with the same length but at different locations of the chip with a maximum relative difference of 20%. The process of thermal cycling and wire bonding was also applied to the samples and caused tender shifts of the frequencies. The experiments reveal major factors that are related to the temperature effects of die attached MEMS and the results are useful for improving the reliability of a package–device co-design.

[1]  Tong-Yi Zhang,et al.  Measurements of residual stresses in thin films using micro-rotating-structures , 1998 .

[2]  Xin Zhang,et al.  Accurate Assessment of Packaging Stress Effects on MEMS Sensors by Measurement and Sensor–Package Interaction Simulations , 2007, Journal of Microelectromechanical Systems.

[3]  Yeong K. Kim,et al.  Finite element simulation of package stress in transfer molded MEMS pressure sensors , 2004, Microelectron. Reliab..

[4]  A. Tseng,et al.  Low stress packaging of a micromachined accelerometer , 2001 .

[5]  Thomas W. Kenny,et al.  Packaging a piezoresistive pressure sensor to measure low absolute pressures over a wide sub-zero temperature range , 2000 .

[6]  C. Basaran,et al.  An Analytical Model for Thermal Stress Analysis of Multi-layered Microelectronic Packaging , 2004, 2005 Conference on High Density Microsystem Design and Packaging and Component Failure Analysis.

[7]  Bongsang Kim,et al.  Effects of stress on the temperature coefficient of frequency in double clamped resonators , 2005, The 13th International Conference on Solid-State Sensors, Actuators and Microsystems, 2005. Digest of Technical Papers. TRANSDUCERS '05..

[8]  Tong Yan Tee,et al.  Advanced warpage prediction methodology for matrix stacked die BGA during assembly processes , 2004, 2004 Proceedings. 54th Electronic Components and Technology Conference (IEEE Cat. No.04CH37546).

[9]  T. Ikehara,et al.  New method for an accurate determination of residual strain in polycrystalline silicon films by analysing resonant frequencies of micromachined beams , 2001 .

[10]  Chang-Chun Lee,et al.  Packaging effect investigation of CMOS compatible pressure sensor using flip chip and flex circuit board technologies , 2006 .

[11]  Stephen F. Bart,et al.  Coupled package-device modeling for microelectromechanical systems , 2000 .

[12]  G. P. Cherepanov,et al.  On the theory of thermal stresses in a thin bonding layer , 1995 .

[13]  Patrick McCluskey,et al.  Thermomechanical analysis of gold-based SiC die-attach assembly , 2003 .

[14]  J. A. Chiou.  Simulations for thermal warpage and pressure nonlinearity of monolithic CMOS pressure sensors , 2003 .

[15]  Chun-Te Lin,et al.  Performance and package effect of a novel piezoresistive pressure sensor fabricated by front-side etching technology , 2005 .

[16]  T. G. Carne,et al.  Experimental modal analysis for microelectromechanical systems , 2005 .

[17]  Ming Li,et al.  Package Level Simulation and Verification of Microsystems , 2007, 2007 IEEE Sensors.

[18]  Ampere A. Tseng,et al.  Low Stress Packaging of a Micromachined , 2001 .

[19]  L. Nicu,et al.  EXPERIMENTAL AND THEORETICAL INVESTIGATIONS ON NONLINEAR RESONANCES OF COMPOSITE BUCKLED MICROBRIDGES , 1999 .

[20]  M. Tsai,et al.  Thermal deformations and stresses of flip chip bga packages with low- and high-T/sub g/ underfills , 2004, 4th IEEE International Conference on Polymers and Adhesives in Microelectronics and Photonics, 2004. POLYTRONIC 2004..