Performance study and analysis of an inclined concentrated photovoltaic-phase change material system

Abstract The performance of an inclined concentrated photovoltaic-phase change material (CPV-PCM) system is investigated. The influence of a CPV-PCM system inclination angle in the range of −45° to 90° in an interval of 45°, with a concentration ratio (CR) of 5, and 20, and a phase change material thickness of 50, and 200 mm, is considered. To determine the effect of these variables on the thermal and electrical behavior of the system, a comprehensive model comprising of the energy equations for CPV layers and a transient melting-solidification thermo-fluid model for the phase change material is developed. The model is numerically simulated, and the predicted results are validated using the available experimental and numerical data. Results indicate that the CPV-PCM system inclination angle has a notable effect on the time required to reach the complete melting state, the transient variation of average cell temperature, and PV local temperature uniformity. It is found that a remarkable reduction of the average solar cell temperature with enhanced uniformity is achieved, as the inclination angle varies from 0° to 90°. On the contrary, at an inclination angle of −45°, the maximum average temperature along with an unfavorable abrupt change of local cell temperature is obtained. In addition, at an inclination angle of 45°, the highest cell electrical efficiency is attained for the entire time period until complete melting occurs, whereas at an inclination angle of −45°, the solar cell electrical efficiency is dramatically reduced with time. The findings of the present study reveal that the CPV-PCM at an inclination angle of 45° reaches the minimum average temperature with reasonable uniformity of local solar cell temperature . These conditions achieve the highest solar cell electrical efficiency and help to prevent hot spots in the solar cell.

[1]  A. Faghri,et al.  Three-dimensional PCM melting in a vertical cylindrical enclosure including the effects of tilting , 2013 .

[2]  Brian Norton,et al.  Evaluation of phase change materials for thermal regulation enhancement of building integrated photovoltaics , 2010 .

[3]  F. Bruno,et al.  Experimental investigation of the effect of inclination angle on convection-driven melting of phase change material in a rectangular enclosure , 2014 .

[4]  Philip C. Eames,et al.  Natural convection in an internally finned phase change material heat sink for the thermal management of photovoltaics , 2011 .

[5]  Jicheng Zhou,et al.  Temperature distribution of photovoltaic module based on finite element simulation , 2015 .

[6]  Tapas K. Mallick,et al.  Enhancing the performance of building integrated photovoltaics , 2011 .

[7]  Philip C. Eames,et al.  Comparison of a Small Scale 3-d PCM Thermal Control Model with a Validated 2-d PCM Thermal Control Model , 2006 .

[8]  P. Stroeve,et al.  Innovation in concentrated solar power , 2011 .

[9]  Jadran Vrabec,et al.  Experimental study of phase change materials for photovoltaic modules: Energy performance and economic yield for the EPEX spot market , 2016 .

[10]  Vaughan R Voller,et al.  ENTHALPY-POROSITY TECHNIQUE FOR MODELING CONVECTION-DIFFUSION PHASE CHANGE: APPLICATION TO THE MELTING OF A PURE METAL , 1988 .

[11]  Mahmoud Ahmed,et al.  Performance enhancement of concentrated photovoltaic systems using a microchannel heat sink with nanofluids , 2016 .

[12]  E. Benini,et al.  Thermal and electrical performance of an integrated PV-PCM system in double skin façades: A numerical study , 2016 .

[13]  Pushpito Kumar Ghosh,et al.  Self regulation of photovoltaic module temperature in V-trough using a metal–wax composite phase change matrix , 2011 .

[14]  Brian Norton,et al.  Phase change materials for photovoltaic thermal management , 2015 .

[15]  M. Saghir,et al.  Effect of thermophoresis on natural convection in a Rayleigh–Benard cell filled with a nanofluid , 2015 .

[16]  C. Dey,et al.  Cooling of photovoltaic cells under concentrated illumination: a critical review , 2005 .

[17]  Mohan Kolhe,et al.  Performance analysis of water cooled concentrated photovoltaic (CPV) system , 2012 .

[18]  Clement Kleinstreuer,et al.  Computational Analysis of Nanofluid Cooling of High Concentration Photovoltaic Cells , 2014 .

[19]  Said Farahat,et al.  Thermal and Electrical Assessment of an Integrated Solar Photovoltaic Thermal (PV/T) Water Collector Equipped with a Compound Parabolic Concentrator (CPC) , 2013 .

[20]  Yuehong Su,et al.  Numerical and experimental study on a PV/T system with static miniature solar concentrator , 2015 .

[21]  M. Eslamian,et al.  Numerical Simulation of Natural Convection of a Nanofluid in an Inclined Heated Enclosure Using Two-Phase Lattice Boltzmann Method: Accurate Effects of Thermophoresis and Brownian Forces , 2015, Nanoscale Research Letters.

[22]  K. Reddy,et al.  Performance enhancement of a Building-Integrated Concentrating Photovoltaic system using phase change material , 2016 .

[23]  D. L. Evans,et al.  Terrestrial concentrating photovoltaic power system studies , 1976 .

[24]  Brian Norton,et al.  Increased photovoltaic performance through temperature regulation by phase change materials: Materials comparison in different climates , 2015 .

[25]  Yogendra Joshi,et al.  Melting in a side heated tall enclosure by a uniformly dissipating heat source , 2001 .

[26]  G. Ziskind,et al.  Melting in a vertical cylindrical tube: Numerical investigation and comparison with experiments , 2010 .

[27]  Taeyeon Kim,et al.  Application of a phase-change material to improve the electrical performance of vertical-building-added photovoltaics considering the annual weather conditions , 2014 .

[28]  Aggelos Zacharopoulos,et al.  Chapter 15. Building Integration of High Concentration Photovoltaic Systems , 2015 .

[29]  Hongxing Yang,et al.  Using phase change materials in photovoltaic systems for thermal regulation and electrical efficiency improvement: A review and outlook , 2015 .

[30]  Pascal Henry Biwole,et al.  Thermal response of poly-crystalline silicon photovoltaic panels: Numerical simulation and experimental study , 2016 .

[31]  Chie Gau,et al.  Effect of natural convection on solidification from above and melting from below of a pure metal , 1985 .

[32]  Brian Norton,et al.  Phase change materials for limiting temperature rise in building integrated photovoltaics , 2006 .

[33]  Shafiqur Rehman,et al.  Performance evaluation of a PV (photovoltaic) module by back surface water cooling for hot climatic conditions , 2013 .

[34]  Oussama Rejeb,et al.  A numerical investigation of a photovoltaic thermal (PV/T) collector , 2015 .

[35]  Pascal Henry Biwole,et al.  Phase-change materials to improve solar panel's performance , 2013 .

[36]  Clement Kleinstreuer,et al.  Concentration photovoltaic–thermal energy co-generation system using nanofluids for cooling and heating , 2014 .

[37]  M. J. Huang,et al.  The effect of using two PCMs on the thermal regulation performance of BIPV systems , 2009 .

[38]  Pascal Henry Biwole,et al.  Heat transfer studies of photovoltaic panel coupled with phase change material , 2016 .

[39]  Mahmoud Ahmed,et al.  Analysis and simulation of concentrating photovoltaic systems with a microchannel heat sink , 2016 .

[40]  Philip C. Eames,et al.  Thermal regulation of building-integrated photovoltaics using phase change materials , 2004 .

[41]  Sanjay Agrawal,et al.  Energy and exergy analysis of hybrid micro-channel photovoltaic thermal module , 2011 .

[42]  K. Kaygusuz,et al.  Experimental study on melting/solidification characteristics of a paraffin as PCM , 2007 .

[43]  Michael J. Allen,et al.  Effect of inclination angle during melting and solidification of a phase change material using a combined heat pipe-metal foam or foil configuration , 2015 .

[44]  M. Eslamian,et al.  Natural convection in a differentially-heated square enclosure filled with a nanofluid: Significance of the thermophoresis force and slip/drift velocity , 2014 .

[45]  William Gerard Hurley,et al.  A thermal model for photovoltaic panels under varying atmospheric conditions , 2010 .

[46]  Brian Norton,et al.  Heat retention of a photovoltaic/thermal collector with PCM , 2016 .

[47]  Lan Xiao,et al.  Performance analysis of photovoltaic–thermoelectric hybrid system with and without glass cover , 2015 .

[48]  V. Tyagi,et al.  Thermal cycle testing of calcium chloride hexahydrate as a possible PCM for latent heat storage , 2008 .

[49]  Shaimaa Abdelbaqi,et al.  Yearly energy performance of a photovoltaic-phase change material (PV-PCM) system in hot climate , 2017 .