Fabrication of flexible UV nanoimprint mold with fluorinated polymer-coated PET film

UV curing nanoimprint lithography is one of the most promising techniques for the fabrication of micro- to nano-sized patterns on various substrates with high throughput and a low production cost. The UV nanoimprint process requires a transparent template with micro- to nano-sized surface protrusions, having a low surface energy and good flexibility. Therefore, the development of low-cost, transparent, and flexible templates is essential. In this study, a flexible polyethylene terephthalate (PET) film coated with a fluorinated polymer material was used as an imprinting mold. Micro- and nano-sized surface protrusion patterns were formed on the fluorinated polymer layer by the hot embossing process from a Si master template. Then, the replicated pattern of the fluorinated polymer, coated on the flexible PET film, was used as a template for the UV nanoimprint process without any anti-stiction coating process. In this way, the micro- to nano-sized patterns of the original master Si template were replicated on various substrates, including a flat Si substrate and curved acryl substrate, with high fidelity using UV nanoimprint lithography.

[1]  Stephen Y. Chou,et al.  Imprint of sub-25 nm vias and trenches in polymers , 1995 .

[2]  K. Tsunozaki,et al.  Preparation methods and characteristics of fluorinated polymers for mold replication , 2009 .

[3]  H. Sumitani,et al.  Improvement of resolution in x-ray lithography by reducing secondary electron blur , 2004 .

[4]  S. Chou,et al.  Imprint Lithography with 25-Nanometer Resolution , 1996, Science.

[5]  Yoshiaki Mimura,et al.  Deep-UV Photolithography , 1978 .

[6]  G. Jung,et al.  UV Curing Nanoimprint Lithography for Uniform Layers and Minimized Residual Layers , 2004 .

[7]  Heon Lee,et al.  Imprinted moth-eye antireflection patterns on glass substrate , 2009 .

[8]  Holger Becker,et al.  Hot embossing as a method for the fabrication of polymer high aspect ratio structures , 2000 .

[9]  Walter Bacher,et al.  Hot embossing - The molding technique for plastic microstructures , 1998 .

[10]  Masaru Sasago,et al.  Mold Surface Treatment for Imprint Lithography. , 2001 .

[11]  J. Shirakashi,et al.  Scratch Nanolithography on Si Surface Using Scanning Probe Microscopy: Influence of Scanning Parameters on Groove Size , 2008 .

[12]  Wolfgang Ehrfeld,et al.  Fabrication of photonic crystals by deep x-ray lithography , 1997 .

[13]  C. Willson,et al.  Step and flash imprint lithography: Template surface treatment and defect analysis , 2000 .

[14]  Richard Martel,et al.  Simple fabrication scheme for sub-10 nm electrode gaps using electron-beam lithography , 2002 .

[15]  M. Isaacson,et al.  Radiolysis and resolution limits of inorganic halide resists , 1985 .

[16]  Bernard Choi,et al.  Step and flash imprint lithography: a new approach to high-resolution patterning , 1999, Advanced Lithography.

[17]  Yan-Kuin Su,et al.  GaN-Based Light-Emitting Diodes Grown on Photonic Crystal-Patterned Sapphire Substrates by Nanosphere Lithography , 2008 .

[18]  Wei Zhang,et al.  Sub-10 nm imprint lithography and applications , 1997, 1997 55th Annual Device Research Conference Digest.

[19]  R. G. Denning,et al.  Fabrication of photonic crystals for the visible spectrum by holographic lithography , 2000, Nature.

[20]  Yasuhide Kawaguchi,et al.  Fluorinated materials for UV nanoimprint lithography , 2007 .

[21]  K. Han,et al.  Fabrication of Sub-100 nm Sized Patterns on Curved Acryl Substrate Using a Flexible Stamp , 2008 .