Modal optimization of doubly clamped base-excited multilayer broadband vibration energy harvesters

Piezoelectric vibration energy harvesters with doubly clamped base-excited multilayer structures have been developed. The vibration energy harvesters consist of stacked H-shaped configurations including up to three beams and two extra masses. One beam is doubly clamped as a base layer. The extra masses are attached between the base layer and the other two beams to connect them together. By altering mass positions and the thickness of the base layer, the vibration energy harvesters can generate considerable power output in up to five modes of vibrations. An optimization strategy is established for multi-resonance broadband vibration energy harvesters designs. The strategy is based on a modal approach, which can determine the modal performance of vibration energy harvesters using mass ratio and electromechanical coupling coefficient. In particular, mass ratio is used to represent the influence of modal mechanical behaviour on the power density. The design strategy is executed by selecting the multilayer configurations with close resonances and preferred values of mass ratios in multiple modes. These configurations have optimal or near-optimal structural performance for broadband power output. The finite element method and a distributed electromechanical parameter model are used to derive the required modal parameters and power output with resistive loads.

[1]  Rupesh Patel.  Modelling analysis and optimisation of cantilever piezoelectric energy harvesters , 2013 .

[2]  Claude Richard,et al.  Energy Harvesting from Ambient Vibrations and Heat , 2009 .

[3]  Norman M. Wereley,et al.  Performance Evaluation of Multi-tier Energy Harvesters Using Macro-fiber Composite Patches , 2009 .

[4]  Huan Xue,et al.  Broadband piezoelectric energy harvesting devices using multiple bimorphs with different operating frequencies , 2008, IEEE Transactions on Ultrasonics, Ferroelectrics and Frequency Control.

[5]  Jan R. Wright,et al.  Design of a multiresonant beam for broadband piezoelectric energy harvesting , 2010 .

[6]  Henry A. Sodano,et al.  A review of power harvesting using piezoelectric materials (2003–2006) , 2007 .

[7]  D. Inman,et al.  On Mechanical Modeling of Cantilevered Piezoelectric Vibration Energy Harvesters , 2008 .

[8]  S. Olutunde Oyadiji,et al.  Modal electromechanical optimization of cantilevered piezoelectric vibration energy harvesters by geometric variation , 2014 .

[9]  Daniel J. Inman,et al.  The bandwidth of optimized nonlinear vibration-based energy harvesters , 2014 .

[10]  Daniel J. Inman,et al.  Analytical Modeling and Experimental Verification of the Vibrations of the Zigzag Microstructure for Energy Harvesting , 2011 .

[11]  Daniel J. Inman,et al.  Modeling of Piezoelectric Energy Harvesting from an L-shaped Beam-mass Structure with an Application to UAVs , 2009 .

[12]  Gopinath Reddy Penamalli,et al.  An efficient vibration energy harvester with a multi-mode dynamic magnifier , 2011 .

[13]  Marco Ferrari,et al.  Piezoelectric multifrequency energy converter for power harvesting in autonomous microsystems , 2008 .

[14]  Yaowen Yang,et al.  Toward Broadband Vibration-based Energy Harvesting , 2010 .

[15]  Andres F. Arrieta,et al.  An experimentally validated double-mass piezoelectric cantilever model for broadband vibration–based energy harvesting , 2012 .

[16]  Yaowen Yang,et al.  A novel two-degrees-of-freedom piezoelectric energy harvester , 2013 .

[17]  N. Hudak,et al.  Small-scale energy harvesting through thermoelectric, vibration, and radiofrequency power conversion , 2008 .

[18]  D. F. Berdya,et al.  Wide-bandwidth , meandering vibration energy harvester with distributed circuit board inertial mass , 2012 .

[19]  Byeng D. Youn,et al.  Robust segment-type energy harvester and its application to a wireless sensor , 2009 .

[20]  M. F. Lumentut,et al.  Analytical techniques for broadband multielectromechanical piezoelectric bimorph beams with multifrequency power harvesting , 2012, IEEE Transactions on Ultrasonics, Ferroelectrics and Frequency Control.

[21]  Daniel J. Inman,et al.  A Distributed Parameter Electromechanical Model for Cantilevered Piezoelectric Energy Harvesters , 2008 .