Determination of the Energy Flux of a Commercial Atmospheric‐Pressure Plasma Jet for Different Process Gases and Distances Between Nozzle Outlet and Substrate Surface

The energy flux of an atmospheric‐pressure plasma jet for surface treatment has been investigated by a calorimetric probe. Generally, the investigations exhibit that the main contributions of the total energy influx from the plasma to the substrate surface originate from the neutrals regarding high gas temperature coupled with a high gas flow. The use of nitrogen as process gas shows a higher energy flux compared to oxygen and air presumably caused by increased gas temperature as well as by higher molecule formation and recombination energy of N2. Moreover, the lateral expansion of the plasma beam could be roughly determined by a spatially resolved analysis of the energy influx. A top part mounted on the nozzle, commonly used for the injection of additional precursor gases, showed a significant effect on the flow behavior and collision entailed relaxation of the excited plasma species leading to a restraining of the plasma jet. (© 2014 WILEY‐VCH Verlag GmbH & Co. KGaA, Weinheim)

[1]  C. Roth,et al.  Electron temperature, ion density and energy influx measurements in a tubular plasma reactor for powder surface modification , 2012 .

[2]  K. Ellmer,et al.  A combined sensor for the diagnostics of plasma and film properties in magnetron sputtering processes , 2012 .

[3]  H. Jouhara,et al.  A novel thermal probe design for the measurement of energy influx in RF remote plasma , 2012 .

[4]  Thomann Anne-Lise,et al.  A Heat Flux Microsensor for Direct Measurements in Plasma Surface Interactions , 2011 .

[5]  M. Häckel,et al.  Aktive Thermosonde zur Messung des Energieeinstromes , 2011 .

[6]  P. Rudolf von Rohr,et al.  Comparison of calorimetric plasma diagnostics in a plasma downstream reactor , 2011 .

[7]  Thomas Arnold,et al.  New Process Simulation Procedure for High-Rate Plasma Jet Machining , 2011 .

[8]  H. Kersten,et al.  Characterization of an atmospheric pressure plasma jet for surface modification and thin film deposition , 2010 .

[9]  T. Trottenberg,et al.  A calorimetric probe for plasma diagnostics. , 2010, The Review of scientific instruments.

[10]  T. Trottenberg,et al.  An experiment for the investigation of forces on microparticles in ion beams. , 2010, The Review of scientific instruments.

[11]  J. Ihde,et al.  Plasma Polymerization of HMDSO with an Atmospheric Pressure Plasma Jet for Corrosion Protection of Aluminum and Low‐Adhesion Surfaces , 2009 .

[12]  Georg Böhm,et al.  Simulation of the Substrate Temperature Field for Plasma Assisted Chemical Etching , 2009 .

[13]  J. Benedikt,et al.  Deposition of silicon dioxide films using an atmospheric pressure microplasma jet , 2009 .

[14]  Jing Zhang,et al.  A hypersonic plasma bullet train traveling in an atmospheric dielectric-barrier discharge jet , 2008 .

[15]  Hans-Erich Wagner,et al.  Atmospheric Pressure Plasma Jet Treatment of Polyethylene Surfaces for Adhesion Improvement , 2007 .

[16]  R. Dussart,et al.  Diagnostic system for plasma/surface energy transfer characterization , 2006 .

[17]  H. Kersten,et al.  Power outflux from the plasma: an important parameter in surface processing , 2004 .

[18]  Jost Degenhardt,et al.  Plasma jet treatment of five polymers at atmospheric pressure: surface modifications and the relevance for adhesion , 2004 .

[19]  F. Scholze,et al.  Characterization of a broad ion beam source by determination of the energy flux , 2003 .

[20]  R. Hippler,et al.  The energy influx during plasma deposition of amorphous hydrogenated carbon films , 2002 .

[21]  Gmw Gerrit Kroesen,et al.  The energy balance at substrate surfaces during plasma processing , 2001 .

[22]  R. Hippler,et al.  Investigations on the energy influx at plasma processes by means of a simple thermal probe , 2000 .

[23]  M. Otte,et al.  Energy influx from an rf plasma to a substrate during plasma processing , 2000 .

[24]  K. Ellmer,et al.  Calorimetric measurements with a heat flux transducer of the total power influx onto a substrate during magnetron sputtering , 1999 .

[25]  H. Kersten,et al.  Investigation of the energy transfer to the substrate during titanium deposition in a hollow cathode arc , 1994 .

[26]  J. Thornton Substrate heating in cylindrical magnetron sputtering sources , 1978 .

[27]  John A. Thornton,et al.  Influence of apparatus geometry and deposition conditions on the structure and topography of thick sputtered coatings , 1974 .

[28]  Robert Gardon,et al.  An Instrument for the Direct Measurement of Intense Thermal Radiation , 1953 .

[29]  M. Fröhlich,et al.  Calorimetric Probes for Energy Flux Measurements in Process Plasmas , 2014 .

[30]  Pascal Tristant,et al.  Atmospheric pressure plasmas: A review , 2006 .

[31]  R. E. Sah,et al.  Amorphous, Hydrogenated Carbon Films and Related Materials: Plasma Deposition and Film Properties , 1991 .