Structural health monitoring using fiber optic distributed sensors for vacuum-assisted resin transfer molding

In this study we implemented manufacturing process and strain monitoring of a composite structure by optical fiber sensors for vacuum-assisted resin transfer molding (VaRTM). Optical fibers with fiber Bragg gratings were embedded into a glass fiber reinforced plastic specimen made by VaRTM and the applicability of structural health monitoring with fiber Bragg grating (FBG) sensors based on optical frequency domain reflectometry (OFDR) was investigated. In this study, long-gage FBGs which are 10 times longer than ordinary FBGs (which are about 10 mm long) were employed for distributed sensing. We can easily map the strain or temperature profile along gratings by OFDR and the spatial resolution of this sensing technique is about 1 mm. The resin flow process in VaRTM could be monitored by measuring the difference in temperature between the resin and preform. Then, the shrinkage of resin could be also monitored during the curing process. The specimen was then subjected to a bending load in a three-point bending test and the strain distributions along the FBGs were measured. From these results we could show the applicability of distributed sensors to quality assurance of a composite structure made by VaRTM and assessment of the structural integrity of in-service composite structures.

[1]  I. Yamaguchi,et al.  Distributed Strain Measurement with High Spatial Resolution Using Fiber Bragg Gratings and Optical Frequency Domain Reflectometry , 2006 .

[2]  Andrew C. Long,et al.  Analysis of the vacuum infusion moulding process: I. Analytical formulation , 2005 .

[3]  Kazuro Kageyama,et al.  Distributed Measurements with a Long Gauge FBG Sensor Using Optical Frequency Domain Reflectometry (1st Report, System Investigation Using Optical Simulation Model) , 2006 .

[4]  Hyun-Kyu Kang,et al.  Cure monitoring of composite laminates using fiber optic sensors , 2002 .

[5]  Suresh G. Advani,et al.  The implications of fiber compaction and saturation on fully coupled VARTM simulation , 2004 .

[6]  B. K. Fink,et al.  Assessment of flow and cure monitoring using direct current and alternating current sensing in vacuum-assisted resin transfer molding , 2000 .

[7]  Peter Mitschang,et al.  Continuous monitoring of three-dimensional resin flow through a fibre preform , 2003 .

[8]  Brooks A. Childers,et al.  Use of 3000 Bragg grating strain sensors distributed on four 8-m optical fibers during static load tests of a composite structure , 2001, SPIE Smart Structures and Materials + Nondestructive Evaluation and Health Monitoring.

[9]  Kazuro Kageyama,et al.  Measurements of strain distributions with a long gauge FBG sensor using optical frequency domain reflectometry , 2005, International Conference on Optical Fibre Sensors.

[10]  Gerard Franklyn Fernando,et al.  In-situ process and condition monitoring of advanced fibre-reinforced composite materials using optical fibre sensors , 1998 .

[11]  Paolo Ermanni,et al.  Linear direct current sensing system for flow monitoring in Liquid Composite Moulding , 2002 .

[12]  E. Schmachtenberg,et al.  Application of ultrasonics for the process control of Resin Transfer Moulding (RTM) , 2005 .

[13]  Michael A. Davis,et al.  Fiber grating sensors , 1997 .

[14]  Dirk Heider,et al.  Flow rate control during vacuum-assisted resin transfer molding (VARTM) processing , 2006 .

[15]  Graham T. Reed,et al.  Optical fibre sensor for monitoring flow and resin curing in composites manufacturing , 2006 .

[16]  Rachid Gafsi,et al.  Analysis of Induced-Birefringence Effects on Fiber Bragg Gratings , 2000 .

[17]  H. Hahn,et al.  A comparative study of vacuum‐assisted resin transfer molding (VARTM) for sandwich panels , 2003 .

[18]  S. Advani,et al.  Permeability estimation algorithm to simultaneously characterize the distribution media and the fabric preform in vacuum assisted resin transfer molding process , 2005 .

[19]  Suresh G. Advani,et al.  Flow front measurements and model validation in the vacuum assisted resin transfer molding process , 2001 .

[20]  A Study on the Measurement Technique of Resin Flow and Cure during the Vacuum Assisted Resin Transfer Moulding Process using the Long Period Fibre Bragg Grating Sensor , 2004 .

[21]  Paolo Ermanni,et al.  Flow monitoring in liquid composite molding based on linear direct current sensing technique , 2003 .

[22]  I. Mondragon,et al.  Cure kinetics and shrinkage model for epoxy-amine systems , 2005 .

[23]  Julie K. Spoerre,et al.  Cure monitoring of the liquid composite molding process using fiber optic sensors , 1997 .

[24]  Nobuo Takeda,et al.  Effect of thermal residual stress on the reflection spectrum from fiber Bragg grating sensors embedded in CFRP laminates , 2002 .

[25]  Hiroshi Tsuda,et al.  Monitoring of resin flow and cure with an electromagnetic wave transmission line using carbon fiber as conductive elements , 2002 .

[26]  W. D Brouwer,et al.  Vacuum injection moulding for large structural applications , 2003 .