Repair of phase defects in extreme-ultraviolet lithography mask blanks

Phase defects that introduce errors in the printed image are one of the major yield limiters for reticles in extreme-ultraviolet lithography. The basis for a reticle is a mask blank, consisting of an ultra-low-expansion substrate and a reflective multilayer stack that is made up of Mo and Si. A potential methodology for repairing phase defects in these mask blanks is to locally irradiate it with a high-resolution electron beam to induce structural deformations that cancel out the distortion of the multilayer. We present experimental and modeling results that show that the interaction of an electron beam with a mask blank can only be understood when the contraction of the multilayer through silicide formation and substrate compaction, as well as the mechanical response of the mask blank, are considered. One of the consequences is that electron beams with energies around 10 keV that are less than 20 nm in diameter induce depressions in multilayers made up of 50 Mo∕Si bilayers that have a surprisingly large ...

[1]  S. Hau-Riege,et al.  Evaluation of the cleanliness of the ion-assisted Mo–Si deposition process for extreme ultraviolet lithography , 2003 .

[2]  J. Davies.  Elastic field in a semi-infinite solid due to thermal expansion or a coherently misfitting inclusion , 2003 .

[3]  Scott Daniel Hector,et al.  Simulation of repairing thin-film phase defect in masks for EUV lithography , 2003, SPIE Advanced Lithography.

[4]  Cindy C. Larson,et al.  Advances in low-defect multilayers for EUVL mask blanks , 2002, SPIE Advanced Lithography.

[5]  D. Stearns,et al.  Practical approach for modeling extreme ultraviolet lithography mask defects , 2002 .

[6]  A. Roberts,et al.  Direct imaging of end-of-range compaction in ion beam irradiated silica waveguides by atomic force microscopy , 2000 .

[7]  Douglas C. Allan,et al.  Densification of fused silica under 193-nm excitation , 1997 .

[8]  David C. Joy,et al.  Monte Carlo Modeling for Electron Microscopy and Microanalysis , 1995 .

[9]  M. E. Kassner,et al.  Silicide layer growth rates in Mo/Si multilayers. , 1992, Applied optics.

[10]  Roger J. Anderson,et al.  The thermal conductivity of rare‐earth–transition‐metal films as determined by the Wiedemann–Franz law , 1990 .

[11]  E. Joseph Friebele,et al.  Effects of radiation on the properties of low thermal expansion coefficient materials: A review , 1989 .

[12]  K. Hill,et al.  Photosensitivity in optical fiber waveguides: Application to reflection filter fabrication , 1978 .

[13]  E. P. EerNisse,et al.  Ionization dilatation effects in fused silica from 2 to 18‐keV electron irradiation , 1974 .

[14]  J. Mansfield.  Studies in Penetration of Charged Particles in Matter , 1965 .

[15]  Sherry L. Baker,et al.  Developing a viable multilayer coating process for extreme ultraviolet lithography reticles , 2004 .

[16]  Donald W. Sweeney,et al.  Method for repairing Mo/Si multilayer thin film phase defects in reticles for extreme ultraviolet lithography , 2001 .

[17]  D. Stearns,et al.  Ultrasmooth, Conducting Films Composed of Mo/Si Multilayers , 1995 .

[18]  W. M. Haynes.  CRC Handbook of Chemistry and Physics , 1990 .

[19]  David C. Joy,et al.  An empirical stopping power relationship for low‐energy electrons , 1989 .

[20]  K. Heinrich,et al.  Use of Monte Carlo calculations in electron probe microanalysis and scanning electron microscopy , 1976 .

[21]  G. Shinoda,et al.  Proceedings of the Sixth International Conference on X-ray optics and microanalysis , 1972 .

[22]  William Primak,et al.  The Radiation Compaction of Vitreous Silica , 1968 .

[23]  L. Rosenhead.  Conduction of Heat in Solids , 1947, Nature.