Enhanced thermoelectric and mechanical properties in textured n-type Bi2Te3 prepared by spark plasma sintering

Abstract n-Type Bi2Te3 thermoelectric materials were prepared by spark plasma sintering (SPS) using mechanically alloyed powders, and fine-grained Bi2Te3 bulks with preferred grain orientation have been fabricated by SPS as a hot-forging process. The effects of orientation degree and hot-forging temperature on thermoelectric properties were investigated. The electrical resistivity was reduced by increasing orientation degree, the Seebeck coefficient was increased by raising hot-forging temperature, and consequently the power factor was significantly increased from 2.1 mW/mK2, measured at 423 K, before hot-forging to 3.1 mW/mK2 after hot-forging at 733 K. The maximum ZT value after hot-forging at 733 K reached 1.18 measured at 423 K. This value was 20% higher than that before hot-forging, although the corresponding thermal conductivity was a little increased after hot-forging. The bending strength was greatly enhanced from 62 MPa to 120 MPa after the hot-forging.

[1]  G. Vineyard,et al.  Semiconductor Thermoelements and Thermoelectric Cooling , 1957 .

[2]  D. Hyun,et al.  Thermoelectric properties of 25%Bi2Te3-75%Sb2Te3 solid solution prepared by hot-pressing method , 1997 .

[3]  J. Noudem,et al.  Bulk textured Ca2.5(RE)0.5Co4O9 (RE: Pr, Nd, Eu, Dy and Yb) thermoelectric oxides by sinter-forging , 2007 .

[4]  Osamu Yamashita,et al.  Bismuth telluride compounds with high thermoelectric figures of merit , 2003 .

[5]  G. R. Miller,et al.  Evidence for the existence of antistructure defects in bismuth telluride by density measurements , 1964 .

[6]  S. Yamanaka,et al.  Thermoelectric properties of Tl9BiTe6 , 2003 .

[7]  K. Fukuda,et al.  Texture and thermoelectric properties of hot-extruded Bi2Te3 compound , 2000 .

[8]  R. J. Radtke,et al.  Thermoelectric properties of anisotropic semiconductors , 2002 .

[9]  T. Masuda,et al.  Fracture strength of tourmaline and epidote by three-point bending test: application to microboudin method for estimating absolute magnitude of palaeodifferential stress , 2006 .

[10]  H. J. Goldsmid,et al.  Recent Studies of Bismuth Telluride and Its Alloys , 1961 .

[11]  P. Klemens,et al.  Thermal conductivity of thermoelectric Si0.8‐Ge0.2 alloys , 1992 .

[12]  V. S. Raghunathan,et al.  Processing and properties of thin films of high critical temperature superconductors , 2003 .

[13]  O. B. Sokolov,et al.  The variation of the equilibrium of chemical reactions in the process of (Bi2Te3)(Sb2Te3)(Sb2Se3) crystal growth , 2002 .

[14]  L. Koudelka,et al.  Energy formation of antisite defects in doped Sb2Te3 and Bi2Te3 crystals , 1986 .

[15]  T. Mitani,et al.  Thermoelectric properties of fine-grained Bi2Te3 alloys , 2005 .

[16]  W. Tiller,et al.  Effects of Heavy Deformation and Annealing on the Electrical Properties of Bi2Te3 , 1962 .

[17]  R. Ionescu,et al.  Grain size effects on thermoelectrical properties of sintered solid solutions based on Bi2Te3 , 1975 .

[18]  F. Lotgering,et al.  Topotactical reactions with ferrimagnetic oxides having hexagonal crystal structures—I , 1959 .

[19]  N. V. Kolomoets,et al.  Thermoelectric properties of the hot-pressed (Bi,Sb) 2 (Te,Se) 3 alloys , 2000 .

[20]  Jingfeng Li,et al.  Effects of process parameters on electrical properties of n-type Bi2Te3 prepared by mechanical alloying and spark plasma sintering , 2007 .

[21]  O. Yamashita,et al.  Influence of annealing on the distribution of thermoelectric figure of merit in bismuth-telluride ingots , 2006 .

[22]  Terry M. Tritt,et al.  Holey and Unholey Semiconductors , 1999, Science.

[23]  Kyeongsoon Park,et al.  Thermoelectric properties of p-type Te doped Bi0.5Sb1.5Te3 fabricated by powder extrusion , 2002 .

[24]  Jingfeng Li,et al.  Effect of nano‐SiC dispersion on thermoelectric properties of Bi2Te3 polycrystals , 2006 .

[25]  H. Chan,et al.  dc bias-induced dielectric anomalies in -oriented 0.9Pb(Mg[sub ⅓]Nb[sub ⅔]O₃)-0.1PbTiO₃ single crystals , 2006 .

[26]  Y. Park,et al.  Structure and transport properties of (Bi1-xSbx)2Te3 thermoelectric materials prepared by mechanical alloying and pulse discharge sintering , 2002 .

[27]  H. Scherrer,et al.  Thermal properties of high quality single crystals of bismuth telluride—Part I: Experimental characterization , 1988 .

[28]  Jun Jiang,et al.  Thermoelectric properties of textured p-type (Bi,Sb)2Te3 fabricated by spark plasma sintering , 2005 .

[29]  N. V. Kolomoets,et al.  Electrical and thermoelectric properties of 90% Bi2Te3-5% Sb2Te3-5% Sb2Se3 single crystals doped with SbI3 , 1998 .

[30]  K. Hartwig,et al.  Microstructural refinement of cast p-type Bi2Te3-Sb2Te3 by equal channel angular extrusion , 2004 .

[31]  J. Yang,et al.  Characterization and thermoelectric properties of p-type 25%Bi2Te3–75%Sb2Te3 prepared via mechanical alloying and plasma activated sintering , 2006 .

[32]  J. Beuth,et al.  Interfacial fracture testing of deposited metal layers under four-point bending , 1997 .

[33]  Ka-Young Park,et al.  Thermoelectric properties of hot-pressed n-type Bi2Te2.85Se0.15 compounds doped with SbI3 , 1997 .

[34]  D. Rowe.  CRC Handbook of Thermoelectrics , 1995 .

[35]  Ka-Young Park,et al.  Fabrication and thermoelectric properties of n-type SbI3-doped Bi2Te2.85Se0.15 compounds by hot extrusion , 1998 .

[36]  M. Kuwabara,et al.  Fabrication of β-BaB_2O_4 thin films with (00l) preferred orientation through the chemical solution deposition technique , 2002 .

[37]  M. Dresselhaus,et al.  Recent developments in thermoelectric materials , 2003 .

[38]  Jun Jiang,et al.  Fabrication and thermoelectric performance of textured n-type Bi2(Te,Se)3 by spark plasma sintering , 2005 .

[39]  B. Chun,et al.  Optimum dopant content of n-type 95% Bi2Te3 + 5% Bi2Se3 compounds fabricated by gas atomization and extrusion process , 2006 .

[40]  Xing Zhang,et al.  Bismuth telluride nanotubes and the effects on the thermoelectric properties of nanotube-containing nanocomposites , 2005 .