Modelling of austenite formation during heating in boron steel hot stamping processes

Abstract A physically-based material model has been developed to describe the austenite formation in a manganese-boron steel during heating in hot stamping processes. The equations were formulated based on three austenite formation mechanisms: nucleation, growth and impingement. It is able to characterize the phase transformation process under both non-isothermal and isothermal conditions, where the effects of heating rate and soaking temperature on the austenite formation have been rationalised. Heat treatment tests of the manganese-boron steel were performed on a Gleeble 3800 subjected to various heating conditions (heating rate: 1–25 K/s, soaking temperature: 1023–1273 K). The dimensional changes of specimens associated with the phase transformation, which was measured using a high resolution dilatometer, has been quantitatively related to the volume fraction of austenite formation. The experimental data were used to calibrate and validate the equations. Good agreement between the experimental and predicted results has been obtained. Further analysis has been made to illustrate the significance of the model in applications.

[1]  H. Khaira,et al.  Effects of heat treatment cycle on equilibrium between ferrite and austenite during intercritical annealing , 1993 .

[2]  Jianguo Lin,et al.  Concept Validation for Selective Heating and Press Hardening of Automotive Safety Components with Tailored Properties , 2014 .

[3]  W. Poole,et al.  Austenite formation during intercritical annealing , 2004 .

[4]  G. Speich,et al.  Formation of Austenite During Intercritical Annealing of Dual-Phase Steels , 1981 .

[5]  Margareth Spangler Andrade,et al.  Kinetics of austenite formation during continuous heating in a low carbon steel , 2007 .

[6]  M. Goodarzi,et al.  Kinetics of Austenite Formation in Dual Phase Steels , 2008 .

[7]  U. Lenel.  TTT curves for the formation of austenite , 1983 .

[8]  C. Capdevila,et al.  Influence of scale parameters of pearlite on the kinetics of anisothermal pearlite-to-austenite transformation in a eutectoid steel , 2000 .

[9]  Yongchang Liu,et al.  A JMAK-like approach for isochronal austenite–ferrite transformation kinetics in Fe–0·055 wt-%N alloy , 2010 .

[10]  Seetharaman Sridhar,et al.  A Study of Diffusion- and Interface-Controlled Migration of the Austenite/Ferrite Front during Austenitization of a Case-Hardenable Alloy Steel , 2007 .

[11]  C. Garcia,et al.  Formation of austenite in 1.5 pct Mn steels , 1981 .

[12]  D. Edmonds,et al.  The formation of austenite in a low-alloy steel , 1980 .

[13]  Jianguo Lin,et al.  Experimental characterisation of the effects of thermal conditions on austenite formation for hot stamping of boron steel , 2016 .

[14]  R. Mclellan,et al.  The diffusivity of carbon in austenite , 1976 .

[15]  M. Avrami.  Granulation, Phase Change, and Microstructure Kinetics of Phase Change. III , 1941 .

[16]  A. Tekkaya,et al.  A review on hot stamping , 2010 .

[17]  C. Capdevila,et al.  Application of dilatometric analysis to the study of solid–solid phase transformations in steels , 2002 .

[18]  W. D. Callister,et al.  Fundamentals of Materials Science and Engineering , 2004 .

[19]  Z. Gácsi,et al.  Isothermal formation of austenite in eutectoid plain carbon steel , 1983 .

[20]  Martin Hunkel,et al.  Modelling the ferrite/carbide → austenite transformation of hypoeutectoid and hypereutectoid steels , 2004 .

[21]  H. Bhadeshia,et al.  A model for austenitisation of hypoeutectoid steels , 2003 .

[22]  C. Bos,et al.  Analysis of solid state phase transformation kinetics: models and recipes , 2007 .

[23]  R. Reed,et al.  Determination of reaustenitisation kinetics in a Fe–0.4C steel using using dilatometry and neutron diffraction , 1998 .