Stopping Sight Distance and Horizontal Sight Line Offsets at Horizontal Curves

Criteria for the design of horizontal curves implicitly rely on design speed to produce safe and efficient designs, particularly for horizontal sight line offsets and stopping sight distances. Current design guidance provides a method for calculating minimum horizontal sight line offsets that is accurate and valid only when both driver and object are within the limits of the curve. Other methods are available to estimate minimum horizontal sight line offsets when the driver, object, or both are not within the curve limits. However, design guidance recommends using the calculated value for offsets as a conservative estimate near the ends of curves. In this study, speed prediction models and reliability theory were used to estimate the probability that drivers would not have enough sight distance to see, react to, and stop before reaching an object in the roadway if horizontal sight line offset criteria were applied when the driver or object was outside the limits of a horizontal curve. Six scenarios at the curve approach and inside the curve were analyzed. Reliability estimates (based on minimum horizontal sight line offsets from current minimum design criteria) and stopping sight distance distributions (based on individual driver characteristics) indicated that the probability of drivers not having enough stopping sight distance was much greater on the approach to than inside the horizontal curves. For improvement of design consistency, the use of calculated horizontal sight line offsets beyond the limits of the curve (approach and departure tangents) is suggested to provide extra sight distance to drivers near the curve.

[1]  Anthony Paul Voigt.  EVALUATION OF ALTERNATIVE HORIZONTAL CURVE DESIGN APPROACHES FOR RURAL TWO-LANE HIGHWAYS , 1996 .

[2]  C J Messer,et al.  HORIZONTAL ALIGNMENT DESIGN CONSISTENCY FOR RURAL TWO-LANE HIGHWAYS. FINAL REPORT , 1995 .

[3]  Eric T. Donnell,et al.  New Insights on Evaluations of Design Consistency for Two-Lane Highways , 2011 .

[4]  Dimitri V. Val,et al.  SAFETY FACTORS FOR ASSESSMENT OF EXISTING STRUCTURES , 2002 .

[5]  Aashto,et al.  A Policy on geometric desing of highways and streets. , 1984 .

[6]  Eric T. Donnell,et al.  Models of acceleration and deceleration rates on a complex two-lane rural highway: Results from a nighttime driving experiment , 2010 .

[7]  Holger R. Maier,et al.  Reliability-Based Approach to Multicriteria Decision Analysis for Water Resources , 2004 .

[8]  D. H. Marks,et al.  Water Distribution Reliability: Analytical Methods , 1988 .

[9]  Eric T. Donnell,et al.  Geometric Design, Speed, and Safety , 2012 .

[10]  Dimitri V. Val,et al.  Role of Load History in Reliability-Based Decision Analysis of Aging Bridges , 1999 .

[11]  Chengchao Xu,et al.  Probabilistic Model for Water Distribution Reliability , 1998 .

[12]  Rune Elvik,et al.  The Handbook of Road Safety Measures , 2009 .

[13]  Timothy R Neuman,et al.  SAFETY AND OPERATIONAL CONSIDERATIONS FOR DESIGN OF RURAL HIGHWAY CURVES. FINAL REPORT , 1983 .

[14]  M. N. Islam,et al.  EVALUATION OF DESIGN CONSISTENCY OF TWO-LANE RURAL HIGHWAYS , 1994 .

[15]  A. Montella.  Safety Evaluation of Curve Delineation Improvements , 2009 .

[16]  M.V.L.R. Anjaneyulu,et al.  Operating Speed of Different Classes of Vehicles at Horizontal Curves on Two-Lane Rural Highways , 2013 .

[17]  R. Krammes,et al.  Speed-Profile Model for a Design-Consistency Evaluation Procedure in the United States , 2000 .

[18]  Said M. Easa,et al.  State of the Art of Highway Geometric Design Consistency , 1999 .

[19]  A Taragin,et al.  DRIVER PERFORMANCE ON HORIZONTAL CURVES , 1954 .

[20]  Achintya Haldar,et al.  Probability, Reliability and Statistical Methods in Engineering Design (Haldar, Mahadevan) , 1999 .

[21]  Nikiforos Stamatiadis,et al.  Development of Accident Reduction Factors , 1996 .

[22]  Gary R. Waissi,et al.  SIGHT DISTANCE RELATIONSHIPS INVOLVING HORIZONTAL CURVES , 1987 .

[23]  Bruce R. Ellingwood,et al.  Reliability-based condition assessment and LRFD for existing structures , 1996 .

[24]  Said M. Easa,et al.  Establishing highway horizontal alignment to maximize design consistency , 2007 .

[25]  Andrew P Tarko,et al.  Speed Factors on Two-Lane Rural Highways in Free-Flow Conditions , 2005 .

[26]  Eric T. Donnell,et al.  Speed Concepts: Informational Guide , 2009 .

[27]  Timur Mauga.  Extension of the AASHTO Model for Horizontal Sightline Offset to Apply to Beginnings and Ends of Simple Horizontal Curves. , 2013 .

[28]  Omer Tsimhoni,et al.  ALTERNATIVE DESIGN CONSISTENCY RATING METHODS FOR TWO-LANE RURAL HIGHWAYS , 2000 .

[29]  R.,et al.  Side Friction . Demanded and Margins of Safety on Horizontal Curves , 2015 .

[30]  L King,et al.  THE NEW AASHTO METRIC POLICY ON GEOMETRIC DESIGN OF HIGHWAYS AND STREETS , 1995 .

[31]  Daniel B. Fambro,et al.  Operating Speeds on Curves With and Without Spiral Transitions , 1999 .

[32]  J F Morrall,et al.  Side friction demanded and margins of safety on horizontal curves , 1994 .

[33]  Yasuhiro Mori,et al.  LRFD for assessment of deteriorating existing structures , 2001 .

[34]  Tarek Sayed,et al.  Risk-Based Highway Design , 2010 .

[35]  Kay Fitzpatrick,et al.  Speed-Profile Model for Two-Lane Rural Highways , 2000 .