Study of tribological properties on Al/Al2O3/MoS2 hybrid composite processed by powder metallurgy

Abstract Aluminium ceramic composites with improved mechanical and chemical properties are essential and needed in aerospace and automotive application. The aluminium matrix composite reinforced with ceramic material of alumina (Al2O3) has good tribological properties. However, aluminium based ceramic composites require improvements in their lubrication properties. In this study an attempt is made in the development of a new material through powder metallurgy technique by the addition of molybdenum disulphide (MoS2), which acts as a solid lubricant. This molybdenum disulphide (MoS2) based solid lubricant has unique advantage that it can be used in vacuum space, but the same is not applicable in case of graphite. The microstructures, material combination, wear and friction properties were analysed by scanning electron microscopy, EDX, and pin-on-disc wear tester. The newly developed aluminium composite has significant improvements in tribological properties with a combination of 5% alumina (Al2O3) and 5% molybdenum disulphide (MoS2). The test reveals that sliding distance of 1000 m and sliding speed of 1.5 m/s with applied load of 5 N result in minimum wear loss of 0.0102 g and coefficient of friction as 0.117.

[1]  B. K. Sridhara,et al.  Effect of addition of graphite particulates on the wear behaviour in aluminium–silicon carbide–graphite composites , 2010 .

[2]  G. Sundararajan,et al.  The sliding wear behaviour of AlSiC particulate composites—I. Macrobehaviour , 1996 .

[3]  N. Radhika,et al.  Tribological Behaviour of Aluminium/Alumina/Graphite Hybrid Metal Matrix Composite Using Taguchi’s Techniques , 2011 .

[4]  S. Kumar,et al.  Mechanical properties of SiCp/Al2O3 ceramic matrix composites prepared by directed oxidation of an aluminum alloy , 2012 .

[5]  F. Akhlaghi,et al.  Effect of the Graphite Content on the Tribological Behavior of Al/Gr and Al/30SiC/Gr Composites Processed by In Situ Powder Metallurgy (IPM) Method , 2011 .

[6]  S. Vijayarangan,et al.  Fabrication, testing and thermal analysis of metal matrix composite brake drum , 2007 .

[7]  F. Akhlaghi,et al.  Effect of SiC content on the processing, compaction behavior, and properties of Al6061/SiC/Gr hybrid composites , 2011 .

[8]  Subsurface microstructures generated by dry sliding wear on as-cast and heat treated Al metal matrix composites , 1997 .

[9]  B. Sridhara,et al.  Wear characteristics of hybrid aluminium matrix composites reinforced with graphite and silicon carbide particulates , 2010 .

[10]  C. Garcia-cordovilla,et al.  Abrasive wear resistance of aluminium alloy/ceramic particulate composites , 1996 .

[11]  Jing Liu,et al.  Wear behaviour and microstructural changes of SiCw-Al composite under unlubricated sliding friction , 1995 .

[12]  G. Sundararajan,et al.  The sliding wear behaviour of AlSiC particulate composites—II. The characterization of subsurface deformation and correlation with wear behaviour , 1996 .

[13]  F. Ahmad,et al.  Wear Resistance of Al-12Si Alloys by Reinforcing TiC and TiN Particles , 2014 .

[14]  S. Prasad,et al.  Aluminum Metal-Matrix Composites for Automotive Applications: Tribological Considerations , 2004 .

[15]  A. Mazahery,et al.  Study on microstructure and abrasive wear behavior of sintered Al matrix composites , 2012 .

[16]  Xuan Zhou,et al.  Friction and wear properties of C/C–SiC braking composites , 2012 .

[17]  Young‐Wook Kim,et al.  Influence of small amount of sintering additives on unlubricated sliding wear properties of SiC ceramics , 2011 .

[18]  A. Mazahery,et al.  Optimization of process conditions in casting aluminum matrix composites via interconnection of artificial neurons and progressive solutions , 2012 .

[19]  K. Manisekar,et al.  Tribological behaviour of powder metallurgy-processed aluminium hybrid composites with the addition of graphite solid lubricant , 2013 .