Influence of quench rate on multi-stage ageing of AA6014 alloy

The influence of quench rate after solution heat treatment on the microstructure in the as-quenched state and subsequent ageing kinetics of alloy AA6014 was investigated by means of transmission electron microscopy, positron annihilation lifetime spectroscopy and hardness measurements. Various ageing temperatures and stages were taken into consideration. Consistent with previous studies, we found that solute and vacancy supersaturation decrease during slow quenching due to precipitation and annihilation, respectively. Additionally, we observed cluster formation during cooling below 200 °C. As for the influence on ageing behaviour we observe different behaviour for high and low ageing temperature: Artificial ageing is more affected than pre-ageing and natural secondary ageing. The detrimental effect of natural ageing on paint-bake hardening also depends on the quench rate. Possible interpretations are associated with cluster formation during natural ageing and also during quenching. The influence of pre-ageing at different temperatures on subsequent ageing kinetics is similar for slower industrial-type quenching and for fast quenching, thus allowing to apply the findings from idealised quenching conditions to situations closer to real application.

[1]  J. Banhart,et al.  Effect of pre-ageing on natural secondary ageing and paint bake hardening in Al–Mg–Si alloys , 2019, Materialia.

[2]  Matthew D. H. Lay,et al.  Quench Sensitivity in a Dispersoid-Containing Al-Mg-Si Alloy , 2019, Metallurgical and Materials Transactions A.

[3]  Qiang-Yan Xu,et al.  Study of precipitation in Al–Mg–Si alloys by Atom Probe Tomography I. Microstructural changes as a function of ageing temperature , 2015 .

[4]  M. Zandbergen,et al.  Data analysis and other considerations concerning the study of precipitation in Al–Mg–Si alloys by Atom Probe Tomography , 2015, Data in brief.

[5]  M. Starink,et al.  Quench sensitivity of Al–Mg–Si alloys: A model for linear cooling and strengthening , 2015 .

[6]  J. Banhart,et al.  Early stages of solute clustering in an Al-Mg-Si alloy , 2015 .

[7]  Tatsuo Sato,et al.  Formation and reversion of clusters during natural aging and subsequent artificial aging in an Al–Mg–Si alloy , 2015 .

[8]  P. Uggowitzer,et al.  Process-controlled suppression of natural aging in an Al-Mg-Si alloy , 2014 .

[9]  Tatsuo Sato,et al.  Effects of Pre-Aging and Natural Aging on Bake Hardening Behavior in Al-Mg-Si Alloys , 2014 .

[10]  Christoph Schick,et al.  Continuous cooling precipitation diagrams of Al-Mg-Si alloys , 2012 .

[11]  E. Kozeschnik,et al.  Precipitation in Al-Alloy 6016 – The Role of Excess Vacancies , 2012 .

[12]  P. Uggowitzer,et al.  Mechanisms controlling the artificial aging of Al-Mg-Si Alloys , 2011 .

[13]  M. Easton,et al.  Relating quench sensitivity to microstructure in 6000 series aluminium alloys , 2011 .

[14]  Rafael Colás,et al.  Quench sensitivity of a heat treatable aluminum alloy , 2003 .

[15]  S. Zając,et al.  Influence of Cooling after Homogenisation and Reheating to Extrusion on Extrudability and Final Properties of AA 6063 and AA6082 Alloys , 2002 .

[16]  M. Starink,et al.  The Effect of Homogenizing on the Quench Sensitivity of 6082 , 2002 .

[17]  N. Ryum,et al.  Precipitation of dispersoids containing Mn and/or Cr in Al-Mg-Si-alloys , 2000 .

[18]  L. Zhen,et al.  The effect of pre-aging on microstructure and tensile properties of Al-Mg-Si alloys , 1997 .

[19]  M. Matsuo,et al.  Effect of Pre-Aging Temperature on the Behavior in the Early Stage of Aging at High Temperature for Al-Mg-Si Alloy , 1996 .

[20]  H. Hirasawa.  Precipitation process of AlMn and AlCr supersaturated solid solution in presence of age hardening phases , 1975 .

[21]  Matthew D. H. Lay,et al.  Effects of quench rate and natural ageing on the age hardening behaviour of aluminium alloy AA6060 , 2016 .

[22]  O. Lohne,et al.  Quench Sensitivity of Almgsi-Alloys Containing Mn or Cr , 1983 .