Factors Affecting Filter Penetration and Quality Factor of Particulate Respirators

In the present study, a theoretical model was used to examine factors affecting the filtration characteristics of filters used for respiratory protection. This work was designed to support the particulate filter test requirements established in 1996. The major operating parameters examined in this work include face velocity, fiber diameter, packing density, filter thickness, and fiber charge density. Characteristics of the most penetrating particle size were also modeled with the same operating parameters. The results showed that aerosol penetration through electret filter media increases with increasing face velocity and increasing fiber diameter, and decreases as packing density, filter thickness or fiber charge density increase. Face velocity and fiber charge density have more significant effects on filter quality than the other factors. Filter quality increases with decreasing face velocity or increasing fiber charge density. For electret filters, (1) the most penetrating particle size increases with increasing fiber diameter; (2) an increase in packing density, thickness, or fiber charge density would cause the most penetrating particle size to decrease, and (3) the most penetrating particle size through electret filters increases with increasing face velocity and decreasing filter thickness. On the other hand, for non-electret filter media, the most penetrating particle size increases with decreasing face velocity, and the filter quality factor is not affected by filter thickness.

[1]  Kenneth L. Rubow,et al.  Air Filtration by Fibrous Media , 1986 .

[2]  K. W. Lee,et al.  Theoretical Study of Aerosol Filtration by Fibrous Filters , 1982 .

[3]  Jing Wang,et al.  Figure of Merit of Composite Filters with Micrometer and Nanometer Fibers , 2008 .

[4]  Heinz Fissan,et al.  Enhancement of particle deposition in filters due to electrostatic effects , 1987 .

[5]  Wen-Yinn Lin,et al.  Experimental Study on the Effect of Fiber Orientation on Filter Quality , 2010 .

[6]  Benjamin Y. H. Liu,et al.  Experimental Study of Aerosol Filtration in the Transition Flow Regime , 1992 .

[7]  Jing Wang,et al.  Investigation of the figure of merit for filters with a single nanofiber layer on a substrate , 2008 .

[8]  Tiina Reponen,et al.  Filter Performance of N99 and N95 Facepiece Respirators Against Viruses and Ultrafine Particles , 2008, The Annals of occupational hygiene.

[9]  Nancy J. Bollinger,et al.  Niosh Guide To Industrial Respiratory Protection , 1987 .

[10]  Nelson A. Leidel ScD.  Upgrading NIOSH's Respirator Approval Requirements—A Public Health Necessity , 1988 .

[11]  J.I.T. Stenhouse,et al.  The effect of particle size, charge, and composition on the loading characteristics of an electrically active fibrous filter material , 1997 .

[12]  Leonard W. Barrett,et al.  Aerosol Loading Performance of Electret Filter Media , 1998 .

[13]  H. Fissan,et al.  Fractional penetrations for electrostatically charged fibrous filters in the submicron particle size range , 1986 .

[14]  R. C. Brown.  REVIEW MODERN CONCEPTS OF AIR FILTRATION APPLIED TO DUST RESPIRATORS , 1989 .

[15]  K Willeke,et al.  Aerosol penetration through filtering facepieces and respirator cartridges. , 1992, American Industrial Hygiene Association journal.

[16]  Tiina Reponen,et al.  Manikin-based performance evaluation of N95 filtering-facepiece respirators challenged with nanoparticles. , 2006, The Annals of occupational hygiene.

[17]  G A Stevens,et al.  "Worst case" aerosol testing parameters: I. Sodium chloride and dioctyl phthalate aerosol filter efficiency as a function of particle size and flow rate. , 1989, American Industrial Hygiene Association journal.

[18]  E. Moyer,et al.  Electrostatic respirator filter media: filter efficiency and most penetrating particle size effects. , 2000, Applied occupational and environmental hygiene.

[19]  Samy Rengasamy,et al.  Respiratory protection against airborne nanoparticles: a review , 2009 .

[20]  H. Fissan,et al.  Deposition of submicron particles on electrically charged fibers , 1986 .

[21]  K. Willeke,et al.  Loading and filtration characteristics of filtering facepieces. , 1993, American Industrial Hygiene Association journal.

[22]  M. L. Laucks,et al.  Aerosol Technology Properties, Behavior, and Measurement of Airborne Particles , 2000 .

[23]  Y. Otani,et al.  Effect of Charging State of Particles on Electret Filtration , 1987 .

[24]  G. Stevens,et al.  "Worst case" aerosol testing parameters: II. Efficiency dependence of commercial respirator filters on humidity pretreatment. , 1989, American Industrial Hygiene Association journal.

[25]  Benjamin Y. H. Liu,et al.  Experimental Study of Electrostatic Capture Mechanisms in Commercial Electret Filters , 1998 .

[26]  Samy Rengasamy,et al.  Nanoparticle penetration through filter media and leakage through face seal interface of N95 filtering facepiece respirators. , 2012, The Annals of occupational hygiene.

[27]  M. Mazumder,et al.  EFFECT OF LOADING WITH AIM OIL AEROSOL ON THE COLLECTION EFFICIENCY OF AN ELECTRET FILTER , 1991 .

[28]  Sheng-Hsiu Huang,et al.  Penetration of 4.5nm to aerosol particles through fibrous filters , 2007 .

[29]  C C Chen,et al.  The effects of particle charge on the performance of a filtering facepiece. , 1998, American Industrial Hygiene Association journal.