A Micromachined Dual-Backplate Capacitive Microphone for Aeroacoustic Measurements

This paper presents the development of a micro-machined dual-backplate capacitive microphone for aeroacoustic measurements. The device theory, fabrication, and characterization are discussed. The microphone is fabricated using the five-layer planarized-polysilicon SUMMiT V process at Sandia National Laboratories. The microphone consists of a 0.46-mm-diameter 2.25-mum-thick circular diaphragm and two circular backplates. The diaphragm is separated from each backplate by a 2-mum air gap. Experimental characterization of the microphone shows a sensitivity of 390 muV/Pa. The dynamic range of the microphone interfaced with a charge amplifier extends from the noise floor of 41 dB/ radicHz up to 164 dB and the resonant frequency is 178 kHz.

[1]  Khalil Najafi,et al.  A silicon micromachined microphone for fluid mechanics research , 2002 .

[2]  B. A. Auld,et al.  Wideband micromachined capacitive microphones with radio frequency detection , 2004 .

[3]  Ole Hansen,et al.  Micromachined double backplate differential capacitive microphone , 1999 .

[4]  S. Timoshenko,et al.  THEORY OF PLATES AND SHELLS , 1959 .

[5]  Wouter Olthuis,et al.  Fabrication of a subminiature silicon condenser microphone using the sacrificial layer technique , 1991, TRANSDUCERS '91: 1991 International Conference on Solid-State Sensors and Actuators. Digest of Technical Papers.

[6]  M. Sheplak,et al.  Surface and bulk micromachined dual back-plate condenser microphone , 2005, 18th IEEE International Conference on Micro Electro Mechanical Systems, 2005. MEMS 2005..

[7]  Richard S. Muller,et al.  Piezoelectric microphone with on-chip CMOS circuits , 1993 .

[8]  Mark Sheplak,et al.  A directional acoustic array using silicon micromachined piezoresistive microphones. , 2003, The Journal of the Acoustical Society of America.

[9]  Ronald N Miles,et al.  Modeling of viscous damping of perforated planar microstructures. Applications in acoustics. , 2004, The Journal of the Acoustical Society of America.

[10]  Lennart Löfdahl,et al.  A small-size silicon microphone for measurements in turbulent gas flows , 1994 .

[11]  Reimund Gerhard-Multhaupt,et al.  Silicon‐dioxide electret transducer , 1984 .

[12]  M. Rossi,et al.  Acoustics and Electroacoustics , 1992 .

[13]  Murat Okandan,et al.  Micromachined microphones with diffraction-based optical displacement detection , 2005 .

[14]  Gisela Hess,et al.  Silicon condenser microphones with corrugated silicon oxide/nitride electret membranes , 2002 .

[15]  M. Sheplak,et al.  Development of a micromachined piezoelectric microphone for aeroacoustics applications. , 2007, The Journal of the Acoustical Society of America.

[16]  W. Janna,et al.  Introduction to Fluid Mechanics , 2012 .

[17]  Mark Sheplak,et al.  Development of a MEMS Dual Backplate Capacitive Microphone for Aeroacoustic Measurements , 2006 .

[18]  Z. Skvor,et al.  On the acoustical resistance due to viscous losses in the air gap of electrotastic transducers , 1969 .

[19]  R. Schellin,et al.  A silicon subminiature microphone based on piezoresistive polysilicon strain gauges , 1992 .

[20]  P. Rombach,et al.  The first low voltage, low noise differential silicon microphone, technology development and measurement results , 2001, Technical Digest. MEMS 2001. 14th IEEE International Conference on Micro Electro Mechanical Systems (Cat. No.01CH37090).

[21]  J. Dugundji,et al.  Large Deflections of Clamped Circular Plates Under Initial Tension and Transitions to Membrane Behavior , 1998 .

[22]  J.J. Sniegowski,et al.  Multi-layer enhancement to polysilicon surface-micromachining technology , 1997, International Electron Devices Meeting. IEDM Technical Digest.

[23]  S. Senturia.  Microsystem Design , 2000 .

[24]  R. D. Ford,et al.  Electroacoustics;: The analysis of transduction, and its historical background , 1954 .

[25]  Ole Hansen,et al.  Design Of A Silicon Microphone With Differential Read-out Of A Sealed Double Parallel-plate Capacitor , 1995, Proceedings of the International Solid-State Sensors and Actuators Conference - TRANSDUCERS '95.

[26]  T. Gabrielson.  Mechanical-thermal noise in micromachined acoustic and vibration sensors , 1993 .

[27]  Wouter Olthuis,et al.  A review of silicon microphones , 1994 .

[28]  M. Royer,et al.  ZnO on Si integrated acoustic sensor , 1983 .

[29]  Gerhard M. Sessler,et al.  High-sensitivity piezoelectric microphones based on stacked cellular polymer films (L) , 2004 .

[30]  A. D. Young,et al.  An Introduction to Fluid Mechanics , 1968 .

[31]  Bin Liu,et al.  A new measurement microphone based on MEMS technology , 2003 .

[32]  Yu-Chong Tai,et al.  A micromachined thin-film Teflon electret microphone , 1997, Proceedings of International Solid State Sensors and Actuators Conference (Transducers '97).

[33]  D. Blackstock.  Fundamentals of Physical Acoustics , 2000 .

[34]  Mark Sheplak,et al.  Sources of excess noise in silicon piezoresistive microphones , 2004 .

[35]  Mark Sheplak,et al.  Design and Characterization of MEMS Optical Microphone for Aeroacoustic Measurement , 2004 .

[36]  Mark Sheplak,et al.  Modal decomposition method for acoustic impedance testing in square ducts. , 2006, The Journal of the Acoustical Society of America.

[37]  Jian Liu,et al.  Nonlinear model and system identification of a capacitive dual-backplate MEMS microphone , 2008 .