3D-printed Lunar regolith simulant-based geopolymer composites with bio-inspired sandwich architectures

[1]  J. Yang,et al.  Er:YAG/Yb:YAG nanopowders‐derived Er/Yb co‐doped yttrium aluminosilicate (YAS) fibers fabricated by UV–curable nanocomposites for 1.5 μm single frequency fiber lasers , 2022, Journal of the American Ceramic Society.

[2]  I. Akhatov,et al.  The effect of particle size of highland and lunar regolith simulants on their printability in vat polymerisation additive manufacturing , 2022, Ceramics International.

[3]  R. Ritchie,et al.  On the damage tolerance of 3-D printed Mg-Ti interpenetrating-phase composites with bioinspired architectures , 2022, Nature Communications.

[4]  A. Radlińska,et al.  Materials Characterization of Various Lunar Regolith Simulants for use in Geopolymer Lunar Concrete , 2022, Advances in Space Research.

[5]  H. Helvajian,et al.  In Situ Resource Utilization of Structural Material from Planetary Regolith , 2021, Advances in Space Research.

[6]  N. Wagner,et al.  Comparison of lunar and Martian regolith simulant-based geopolymer cements formed by alkali-activation for in-situ resource utilization , 2021, Advances in Space Research.

[7]  T. Alomayri.  Performance evaluation of basalt fiber-reinforced geopolymer composites with various contents of nano CaCO3 , 2021 .

[8]  Yu Zhou,et al.  Formation of SiC whiskers/leucite-based ceramic composites from low temperature hardening geopolymer , 2021, Ceramics International.

[9]  Xiaohong Sun,et al.  Dense ceramics with complex shape fabricated by 3D printing: A review , 2021, Journal of Advanced Ceramics.

[10]  Kinga Korniejenko,et al.  Geopolymers reinforced by short and long fibres – innovative materials for additive manufacturing , 2020 .

[11]  A. Ditta,et al.  Preliminary 3D printing of large inclined-shaped alumina ceramic parts by direct ink writing , 2020, Journal of Advanced Ceramics.

[12]  A. Zocca,et al.  Investigation of the sintering and melting of JSC-2A lunar regolith simulant , 2020, Ceramics International.

[13]  Zhihua Yang,et al.  Direct ink writing of continuous SiO2 fiber reinforced wave-transparent ceramics , 2020, Journal of Advanced Ceramics.

[14]  A. Meurisse,et al.  EAC-1A: A novel large-volume lunar regolith simulant , 2020, Scientific Reports.

[15]  G. J. Taylor,et al.  Modal analyses of lunar soils by quantitative X-ray diffraction analysis , 2019, Geochimica et Cosmochimica Acta.

[16]  E. Duoss,et al.  Fiber motion in highly confined flows of carbon fiber and non-Newtonian polymer , 2019, Journal of Non-Newtonian Fluid Mechanics.

[17]  Lifeng Wang,et al.  3D Printing of Biomimetic Composites with Improved Fracture Toughness , 2018, Acta Materialia.

[18]  Qiang Zhang,et al.  Preparation and characterization of bioinspired three-dimensional architecture of zirconia on ceramic surface , 2018, Composites Part B: Engineering.

[19]  Ming Jen Tan,et al.  Investigation of the rheology and strength of geopolymer mixtures for extrusion-based 3D printing , 2018, Cement and Concrete Composites.

[20]  M. Zawrah,et al.  Improvement of physical and mechanical properties of geopolymer through addition of zircon , 2018, Materials Chemistry and Physics.

[21]  A. Akbarzadeh,et al.  3D printed architected polymeric sandwich panels: Energy absorption and structural performance , 2018, Composite Structures.

[22]  Paolo Colombo,et al.  Direct ink writing of geopolymeric inks , 2017 .

[23]  X. Cui,et al.  Lunar regolith can allow the synthesis of cement materials with near-zero water consumption , 2017 .

[24]  M. Meyer,et al.  Geopolymers from lunar and Martian soil simulants , 2017 .

[25]  J. Sanjayan,et al.  Method of formulating geopolymer for 3D printing for construction applications , 2016 .

[26]  Zhihua Yang,et al.  Crystallization kinetics and microstructure evolution of reduced graphene oxide/geopolymer composites , 2016 .

[27]  Francisco Chinesta,et al.  A multi-scale description of orientation in simple shear flows of confined rod suspensions , 2016 .

[28]  Zhihua Yang,et al.  SiC fiber reinforced geopolymer composites, part 1: Short SiC fiber , 2016 .

[29]  E. Saiz,et al.  Ultralight, Strong, Three-Dimensional SiC Structures. , 2016, ACS nano.

[30]  Faiz Shaikh,et al.  Characterisation of mechanical and thermal properties in flax fabric reinforced geopolymer composites , 2015, Journal of Advanced Ceramics.

[31]  M. Meyers,et al.  Structural Design Elements in Biological Materials: Application to Bioinspiration , 2015, Advanced materials.

[32]  J. Lewis,et al.  3D‐Printing of Lightweight Cellular Composites , 2014, Advanced materials.

[33]  L. Gibson.  The hierarchical structure and mechanics of plant materials , 2012, Journal of The Royal Society Interface.

[34]  S. Reis,et al.  JSC-1A lunar soil simulant: Characterization, glass formation, and selected glass properties , 2010 .

[35]  Prinya Chindaprasirt,et al.  Influence of NaOH solution on the synthesis of fly ash geopolymer , 2009 .

[36]  S. S. Rout,et al.  Spectral properties of simulated impact glasses produced from martian soil analogue JSC Mars-1 , 2009 .

[37]  Tiesong Lin,et al.  Effects of fiber length on mechanical properties and fracture behavior of short carbon fiber reinforced geopolymer matrix composites , 2008 .

[38]  Christine Ortiz,et al.  Bioinspired Structural Materials , 2008, Science.

[39]  R. Rieder,et al.  Chemistry of Rocks and Soils in Gusev Crater from the Alpha Particle X-ray Spectrometer , 2004, Science.