Heat flux calculation and problem of flaking of boron carbide coatings on the Faraday screen of the ICRH antennas during Tore Supra high power, long pulse operation

Abstract Reliable and repetitive high power and long pulse tokamak operation is strongly dependant of the ability to secure the Plasma Facing Components (PFCs). In Tore Supra, a network of 7 infrared (IR) video cameras is routinely used to prevent PFCs overheating and damage in selected regions. Real time feedback control and offline analysis are essential for basic protection and understanding of abnormal thermal events. One important limitation detected by the IR real time feed-back loop during high power RF operation (injected power of 9.5 MW over 26 s and 12 MW over 10 s have been achieved respectively in 2006 and 2008) is due to the interaction between fast ions which increase the power flux density and flaking of the boron carbide coatings on the Faraday screen box of the ICRH antennas. An IR-based experimental procedure is proposed in order to detect new flakes during plasma operation. The thermal response of the B 4 C coating is studied with and without flaking during plasma operation. The experimental heat flux deposited by fast ion losses on the Faraday screen is calculated for high (3.8 T) and low magnetic field (2 T) during high RF power operation (with fundamental hydrogen minority and second harmonic ICRH heating schemes respectively). The paper addresses both thermal science issues applied to machine protection and limitation due to fast ions issues during high RF power, long pulse operation. Safety margin to critical heat flux and number of fatigue cycles under heat load are presented in the paper.

[1]  T. Loarer,et al.  Evolution of Carbon Tiles During Repetitive Long Pulse Operation in TORE SUPRA , 2004 .

[2]  E. Yadlowsky,et al.  Vacuum Arc Deposited Boron Carbide Films for Fusion Plasma Facing Components , 2001 .

[3]  D. Guilhem,et al.  Tore-Supra infrared thermography system, a real steady-state diagnostic , 2005 .

[4]  Evidence for Regions of Nearly Suppressed Velocity Space Diffusion Caused by Finite Larmor Radius Effects during ICRF Heating , 1999 .

[5]  A. Becoulet,et al.  Tore Supra steady-state power and particle injection: the ‘CIMES’ project , 2001 .

[6]  P. Gąsior,et al.  34th European Physical Society Conference on Plasma Physics , 2007 .

[7]  V. V. Bolotin,et al.  Mechanical Engineering Series , 2001 .

[8]  M. Chatelier.  Physics and design interplay phenomena in an actively cooled tokamak: Tore Supra , 2001 .

[9]  Gianfranco Tonon,et al.  EQUIPE TORE SUPRA , 1992 .

[10]  B. Beaumont,et al.  Tore Supra ICRH antennas for long pulse operation , 1997, 17th IEEE/NPSS Symposium Fusion Engineering (Cat. No.97CH36131).

[11]  J. Fabre,et al.  Critical heat flux of water subcooled flow in one-side heated swirl tubes , 1999 .

[12]  C. Laviron,et al.  Investigation of steady-state tokamak issues by long pulse experiments on Tore Supra , 2009 .

[13]  V. Basiuk,et al.  Ripple losses during ICRF heating in Tore Supra , 2004 .

[14]  E. Joffrin,et al.  Thermal and non-thermal particle interaction with the LHCD launchers in Tore Supra , 2007 .

[15]  V. Moncada,et al.  Integrated software for imaging data analysis applied to edge plasma physic and operational safety , 2011 .

[16]  L. Colas,et al.  RF current distribution and topology of RF sheath potentials in front of ICRF antennae , 2005 .

[17]  R. Mitteau,et al.  RF heating optimization on Tore Supra using feedback control of infrared measurements , 2007 .

[18]  D. Van Eester,et al.  Re-evaluation of ITER ion cyclotron operating scenarios , 2002 .

[19]  R. Mitteau,et al.  High heat flux components in fusion devices: from current experience in Tore Supra towards the ITER challenge , 2004 .

[20]  M. Chatelier.  Integration of high power, long pulse operation in Tore Supra in preparation for ITER , 2007 .

[21]  M. Merola,et al.  Qualification, commissioning and in situ monitoring of high heat flux plasma facing components , 2007 .

[22]  Eric Gauthier,et al.  Infrared surface temperature measurements for long pulse operation, and real time feedback control in Tore-Supra, an actively cooled Tokamak , 2005 .

[23]  B. Mishra,et al.  Wear behavior of B4C–Mo co-sputtered wear coatings , 2001 .

[24]  Frederic Escourbiac,et al.  Advanced qualification methodology for actively cooled plasma facing components , 2007 .

[25]  R. Mitteau,et al.  Design criteria for Tore Supra high heat flux components , 2001 .

[26]  B. Beaumont,et al.  High power density and long pulse operation with Tore Supra ICRF facility , 2003 .

[27]  G. T. Hoang,et al.  On the role of ion heating in ICRF heated discharges in Tore Supra , 2001 .

[28]  E. Gauthier,et al.  Characterisation of Boron Carbide Coatings for Actively Cooled Plasma Facing Components , 1995 .

[29]  R. Mitteau,et al.  Key results of long pulse ICRH operation in Tore Supra , 2006 .

[30]  V. Basiuk,et al.  Ion Cyclotron Resonant Heating in Tore Supra , 2009 .

[31]  R. Goldston,et al.  Effects of toroidal field ripple on suprathermal ions in tokamak plasmas , 1981, Journal of Plasma Physics.