Durability of FRP - concrete bonded joints in structural rehabilitation: A review

Abstract Fibre Reinforced Polymer (FRP) composites have been the source of an increasing interest in the field of rehabilitation, namely for repair and strengthening of reinforced concrete (RC) structures. One of the most effective techniques comprises externally bonded FRP composites, in which the efficacy of rehabilitation depends considerably on the integrity and durability of the bond established between the FRP and the substrate, which is provided by a structural adhesive. This paper presents a concise review of critical durability issues associated with the structural bond between FRP and concrete for rehabilitation purposes. A number of factors determining the durability of FRP-concrete bonded joints have been identified and grouped into the following categories: materials – adhesive and adherends, joint characteristics and in-service conditions. For each of those factors, the main findings obtained in previous studies are summarized and the aspects that need further investigation are outlined.

[1]  S. A. Grammatikos,et al.  On the response to hygrothermal aging of pultruded FRPs used in the civil engineering sector , 2016 .

[2]  Bankim Chandra Ray,et al.  Environmental effects on fibre reinforced polymeric composites: evolving reasons and remarks on interfacial strength and stability. , 2015, Advances in colloid and interface science.

[3]  Lawrence C. Bank,et al.  Accelerated Test Methods to Determine the Long-Term Behavior of FRP Composite Structures: Environmental Effects , 1995 .

[4]  G. Mays,et al.  Adhesives in Civil Engineering , 1992 .

[5]  Julien Michels,et al.  Mechanical performance of cold-curing epoxy adhesives after different mixing and curing procedures , 2016 .

[6]  Jeffrey S. Russell,et al.  A model specification for FRP composites for civil engineering structures , 2003 .

[7]  C. Poggi,et al.  Bond strength of CFRP–concrete elements under freeze–thaw cycles , 2010 .

[8]  R. Haghani,et al.  Environmental durability of adhesively bonded FRP/steel joints in civil engineering applications: State of the art , 2015 .

[9]  Hui Li,et al.  Durability study of pultruded CFRP plates immersed in water and seawater under sustained bending: Water uptake and effects on the mechanical properties , 2015 .

[10]  Vistasp M. Karbhari,et al.  Comparative durability evaluation of ambient temperature cured externally bonded CFRP and GFRP composite systems for repair of bridges , 2009 .

[11]  L. Bank.  Composites for Construction: Structural Design with FRP Materials , 2006 .

[12]  E. Douglas,et al.  Accelerated Testing of Epoxy-FRP Composites for Civil Infrastructure Applications: Property Changes and Mechanisms of Degradation , 2012 .

[13]  E. Douglas,et al.  Effects of hygrothermal conditioning on epoxy adhesives used in FRP composites , 2015 .

[14]  M. Frigione,et al.  Effects of humid environment on thermal and mechanical properties of a cold-curing structural epoxy adhesive , 2012 .

[15]  Michel Ghosn,et al.  Freeze–thaw degradation of FRP–concrete interface: Impact on cohesive fracture response , 2008 .

[16]  C. Czaderski,et al.  Glass transition evaluation of commercially available epoxy resins used for civil engineering applications , 2015 .

[17]  Mark F. Green,et al.  Investigation of insulated FRP-wrapped reinforced concrete columns in fire , 2007 .

[18]  Vistasp M. Karbhari,et al.  Durability characterization of wet layup graphite/epoxy composites used in external strengthening , 2005 .

[19]  L.F.M. da Silva,et al.  Effect of Cure Temperature on the Glass Transition Temperature and Mechanical Properties of Epoxy Adhesives , 2014 .

[20]  M. Lavorgna,et al.  Improved mechanical properties of CFRP laminates at elevated temperatures and freeze–thaw cycling , 2012 .

[21]  J. R. Correia,et al.  Experimental characterization of the bond between externally bonded reinforcement (EBR) CFRP strips and concrete at elevated temperatures , 2015 .

[22]  M. Green,et al.  Behaviour of fibre reinforced polymer-strengthened T-beams and slabs in fire , 2012 .

[23]  Xu Chen,et al.  Moisture sorption-desorption-resorption characteristics and its effect on the mechanical behavior of the epoxy system , 2005 .

[24]  Zhishen Wu,et al.  Tensile behavior of FRP and hybrid FRP sheets in freeze-thaw cycling environments , 2014 .

[25]  J. Mottram,et al.  Moisture uptake characteristics of a pultruded fibre reinforced polymer flat sheet subjected to hot/wet aging , 2015 .

[26]  Mark F. Green,et al.  Fire Endurance of Fiber-Reinforced Polymer-Confined Concrete Columns , 2005 .

[27]  João Custódio,et al.  Rehabilitation of timber structures – Preparation and environmental service condition effects on the bulk performance of epoxy adhesives , 2011 .

[28]  Amr I. I. Helmy,et al.  Effect of thermal exposure on the mechanical properties of polymer adhesives , 2017 .

[29]  Y. Mai,et al.  Surface treatments and adhesion bonding between concrete and a CFRP composite , 1998 .

[30]  Polycarpos Pissis,et al.  Water sorption and diffusion studies in an epoxy resin system , 1999 .

[31]  Venkatesh Kodur,et al.  Effect of high temperature on bond strength of near-surface mounted FRP reinforcement , 2014 .

[32]  Yifu Ding,et al.  Water Transportation in Epoxy Resin , 2005 .

[33]  Michael F. Petrou,et al.  The Effect of the Presence of Water on the Durability of Bond between CFRP and Concrete , 2006 .

[34]  J. Sena-Cruz,et al.  Effects of different environmental conditions on the mechanical characteristics of a structural epoxy , 2016 .

[35]  C. Czaderski,et al.  Effect of curing conditions on strength development in an epoxy resin for structural strengthening , 2012 .

[36]  Vistasp M. Karbhari,et al.  Materials Considerations in FRP Rehabilitation of Concrete Structures , 2001 .

[37]  Lisa Holliday,et al.  Interaction of environmental factors on fiber-reinforced polymer composites and their inspection and maintenance: A review , 2014 .

[38]  J. Myers.  Durability of external fiber-reinforced polymer strengthening systems , 2007 .

[39]  Maria Antonietta Aiello,et al.  Water effects on the bond strength of concrete/concrete adhesive joints , 2006 .

[40]  L. Carlsson,et al.  Evaluation of water degradation of vinylester and epoxy matrix composites by single fiber and composite tests , 2008, Journal of Materials Science.

[41]  Fernando A. Branco,et al.  Artificial Accelerated Ageing of GFRP Pultruded Profiles Made of Polyester and Vinylester Resins: Characterisation of Physical–Chemical and Mechanical Damage , 2012 .

[42]  Julio C. López-González,et al.  Effect of Adhesive Thickness and Concrete Strength on FRP-Concrete Bonds , 2012 .

[43]  Andrea Prota,et al.  Influence of surface roughness on the bond of FRP laminates to concrete , 2013 .

[44]  Amar Patnaik,et al.  A review on application of structural adhesives in concrete and steel–concrete composite and factors influencing the performance of composite connections , 2017 .

[45]  S. Cabral-Fonseca,et al.  Advanced fibre-reinforced polymer (FRP) composites for the rehabilitation of timber and concrete structures: assessing strength and durability , 2013 .

[46]  Ema Kato,et al.  Experimental Investigation of the Influence of Moisture on the Bond Behavior of FRP to Concrete Interfaces , 2010 .

[47]  John W. Gillespie,et al.  Moisture diffusion in epoxy systems , 1999 .

[48]  M. Fernández-García,et al.  Relation of swelling and Tg depression to the apparent free volume of a particle-filled, epoxy-based adhesive† , 2003 .

[49]  M. Green,et al.  Effects of elevated temperature on near surface mounted and externally bonded FRP strengthening systems for concrete , 2013 .

[50]  F. E. Karasz,et al.  Epoxy‐water interactions , 1980 .

[51]  R. Gravina,et al.  Durability of adhesively bonded FRP-to-concrete joints , 2016 .

[52]  V. Karbhari,et al.  Low‐temperature hygrothermal degradation of ambient cured E‐glass/vinylester composites , 2002 .

[53]  Yufei Wu,et al.  Durability of CFRP–concrete joints under freeze–thaw cycling , 2011 .

[54]  V. Kodur,et al.  Fire endurance of fiber-reinforced polymer strengthened concrete T-Beams , 2008 .

[55]  P. Lourenço,et al.  Effect of synergistic environmental conditions on thermal properties of a cold curing epoxy resin , 2017 .

[56]  João R. Correia,et al.  Fire behaviour of thermally insulated RC beams strengthened with NSM-CFRP strips: Experimental study , 2015 .

[57]  J. R. Correia,et al.  Bond Behavior between Near-Surface-Mounted CFRP Strips and Concrete at High Temperatures , 2015 .

[58]  José Luís Duarte Granja,et al.  Influence of temperature on the curing of an epoxy adhesive and its influence on bond behaviour of NSM-CFRP systems , 2016 .

[59]  A. Machida,et al.  Fiber-Reinforced Polymer Composites for Construction—State-of-the-Art Review , 2002 .

[60]  Abulgasem Mohamed Elarbi,et al.  Effect of hot temperature on pull-off strength of FRP bonded concrete , 2015 .

[61]  B. Benmokrane,et al.  Durability Gap Analysis for Fiber-Reinforced Polymer Composites in Civil Infrastructure , 2003 .

[62]  A. Mouritz,et al.  Fire Properties of Polymer Composite Materials , 2006 .

[63]  Hui Li,et al.  Freeze–thaw resistance of unidirectional-fiber-reinforced epoxy composites , 2012 .

[64]  Oded Rabinovitch,et al.  Mechanical behavior of concrete–resin/adhesive–FRP structural assemblies under low and high temperatures , 2016 .

[65]  Anastasios P. Vassilopoulos,et al.  Early-age tensile properties of structural epoxy adhesives subjected to low-temperature curing , 2012 .

[66]  Vistasp M. Karbhari,et al.  Investigation of durability and surface preparation associated defect criticality of composites bonded to concrete , 2008 .

[67]  Jiming Zhou,et al.  Hygrothermal effects of epoxy resin. Part I: the nature of water in epoxy , 1999 .

[68]  Brahim Benmokrane,et al.  Field study of glass-fibre-reinforced polymer durability in concrete , 2007 .

[69]  A. P. Vassilopoulos,et al.  Effects of aging in dry environment on physical and mechanical properties of a cold-curing structural epoxy adhesive for bridge construction , 2017 .

[70]  V. M. Karbhari,et al.  Effect of Environmental Exposure on the External Strengthening of Concrete with Composites-Short Term Bond Durability , 1996 .

[71]  J. R. Correia,et al.  Fire behaviour of thermally insulated RC beams strengthened with EBR-CFRP strips: Experimental study , 2015 .

[72]  M. Fernández-García,et al.  Effect of hygrothermal aging history on sorption process, swelling, and glass transition temperature in a particle‐filled epoxy‐based adhesive , 2002 .

[73]  Maria Antonietta Aiello,et al.  Effect of elevated service temperature on bond between FRP EBR systems and concrete , 2009 .

[74]  Mark F. Green,et al.  Fire insulation schemes for FRP-strengthened concrete slabs , 2006 .

[75]  I. McEwan,et al.  Influence of stoichiometric ratio on water absorption in epoxy resins , 1998 .

[76]  S. Choi,et al.  Durability of Concrete Beams Externally Reinforced with CFRP Composites Exposed to Various Environments , 2012 .

[77]  V. Karbhari,et al.  Issues of variability and durability under synergistic exposure conditions related to advanced polymer composites in the civil infrastructure , 2006 .

[78]  A. Apicella,et al.  Effect of water on the properties of epoxy matrix and composite , 1985 .

[79]  Bahram M. Shahrooz,et al.  Environmental durability of externally bonded FRP materials intended for repair of concrete structures , 2011 .

[80]  T. Kang,et al.  Independent environmental effects on durability of fiber-reinforced polymer wraps in civil applications: A review , 2013 .

[81]  Helena Cruz,et al.  A review of factors influencing the durability of structural bonded timber joints , 2009 .

[82]  C. Soles,et al.  A discussion of the molecular mechanisms of moisture transport in epoxy resins , 2000 .

[83]  L. Hollaway.  A review of the present and future utilisation of FRP composites in the civil infrastructure with reference to their important in-service properties , 2010 .

[84]  Maria Antonietta Aiello,et al.  Wet Lay-Up Manufactured FRPs for Concrete and Masonry Repair: Influence of Water on the Properties of Composites and on Their Epoxy Components , 2010 .

[85]  R. Pethrick,et al.  Dielectric studies of water in epoxy resins , 1983 .

[86]  Zhishen Wu,et al.  Durability of Wet Bond of Hybrid Laminates to Cast-in-Place Concrete , 2010 .

[87]  Luke Bisby,et al.  Fire behaviour of FRP-strengthened reinforced concrete structural elements: A state-of-the-art review , 2015 .

[88]  Guangming Chen,et al.  Fatigue behavior of FRP–concrete bond under hygrothermal environment , 2015 .

[90]  R. El-Hacha,et al.  Effect of Severe Environmental Exposures on CFRP Wrapped Concrete Columns , 2010 .

[91]  H. Hamilton,et al.  Comparison of laboratory and field environmental conditioning on FRP-concrete bond durability , 2016 .

[92]  L. Goglio,et al.  Variations in mechanical properties of an epoxy adhesive on exposure to warm moisture , 2014 .

[93]  M. Leeming,et al.  Strengthening of reinforced concrete structures : using externally-bonded FRP composites in structural and civil engineering , 1999 .

[94]  V. Karbhari,et al.  Interlaminar and intralaminar durability characterization of wet layup carbon/epoxy used in external strengthening , 2006 .

[95]  M. I. Kabir,et al.  Effects of applied environmental conditions on the pull-out strengths of CFRP-concrete bond , 2016 .

[96]  C. S. Poon,et al.  Effects of elevated water temperatures on interfacial delaminations, failure modes and shear strength in externally-bonded CFRP-concrete beams using infrared thermography, gray-scale images and direct shear test , 2009 .

[98]  Lixin Wu,et al.  Effects of water on the curing and properties of epoxy adhesive used for bonding FRP composite sheet to concrete , 2004 .

[99]  V. Karbhari,et al.  On the durability of composite rehabilitation schemes for concrete: use of a peel test , 1997 .

[100]  Michael J. Adamson,et al.  Thermal expansion and swelling of cured epoxy resin used in graphite/epoxy composite materials , 1980 .

[101]  Tinh Nguyen,et al.  Effects of water, salt solution and simulated concrete pore solution on the properties of composite matrix resins used in civil engineering applications , 2001 .

[102]  M. Quiertant,et al.  Accelerated ageing behaviour of the adhesive bond between concrete specimens and CFRP overlays , 2011 .

[103]  J. P. Lucas,et al.  Hygrothermal effects of epoxy resin. Part II : Variations of glass transition temperature , 1999 .

[104]  L. C. Hollaway,et al.  Advanced Polymer Composites and Polymers in the Civil Infrastructure , 2001 .

[105]  M. Boulfiza,et al.  Durability of GFRP Rebars in Simulated Concrete Solutions under Accelerated Aging Conditions , 2011 .

[106]  Yingfeng Yu,et al.  Effect of chemical structure on the water sorption of amine-cured epoxy resins , 2009 .

[107]  Vistasp M. Karbhari,et al.  Design factors, reliability, and durability prediction of wet layup carbon/epoxy used in external strengthening , 2007 .

[108]  Characteristics of concrete/CFRP bonding system under natural tropical climate , 2015 .

[109]  A. P. Vassilopoulos,et al.  Time-temperature dependence of thermomechanical recovery of cold-curing structural adhesives , 2012 .

[110]  Luc Taerwe,et al.  Experimental investigation on fire endurance of insulated concrete beams strengthened with near surface mounted FRP bar reinforcement , 2012 .

[111]  José Sena-Cruz,et al.  Durability of RC slabs strengthened with prestressed CFRP laminate strips under different environmental and loading conditions , 2017 .

[112]  G. Pritchard.  Reinforced Plastics Durability , 1999 .

[113]  Guijun Xian,et al.  Hygrothermal Ageing of an Epoxy Adhesive Used in FRP Strengthening of Concrete , 2008 .