A New Hybrid Sensitive PANI/SWCNT/Ferrocene-Based Layer for a Wearable CO Sensor

Developing a sensing layer with high electroactive properties is an important aspect for proper functionality of a wearable sensor. The polymeric nanocomposite material obtained by a simple electropolymerization on gold interdigitated electrodes (IDEs) can be optimized to have suitable conductive properties to be used with direct current (DC) measurements. A new layer based on polyaniline:poly(4-styrenesulfonate) (PANI:PSS)/single-walled carbon nanotubes (SWCNT)/ferrocene (Fc) was electrosynthesized and deposed on interdigital transducers (IDT) and was characterized in detail using electrochemical impedance spectroscopy (EIS), cyclic voltammetry (CV), scanning electron microscopy (SEM), Raman spectroscopy, X-ray photoemission spectroscopy (XPS), and X-ray diffraction (XRD). The sensor characteristics of the material towards carbon monoxide (CO) in the concentration range of 10–300 ppm were examined, showing a minimal relative humidity interference of only 1% and an increase of sensitivity with the increase of CO concentration. Humidity interference could be controlled by the number of CV cycles when a compact layer was formed and the addition of Fc played an important role in the decrease of humidity. The results for CO detection can be substantially improved by optimizing the number of deposition cycles and enhancing the Fc concentration. The material was developed for selective detection of CO in real environmental conditions and shows good potential for use in a wearable sensor.

[1]  Ulrich S Schubert,et al.  Inkjet printing as a deposition and patterning tool for polymers and inorganic particles. , 2008, Soft matter.

[2]  Ting Zhang,et al.  A gas nanosensor unaffected by humidity , 2009, Nanotechnology.

[3]  Bharat B. Kale,et al.  Ink-jet printed conducting polyaniline based flexible humidity sensor , 2013 .

[4]  Bogdan Firtat,et al.  Polyaniline Working Electrodes For Glucose Sensing , 2019, 2019 International Semiconductor Conference (CAS).

[5]  Xueyi Guo,et al.  Bifacial quasi-solid-state dye-sensitized solar cells with Poly (vinyl pyrrolidone)/polyaniline transparent counter electrode , 2016 .

[6]  H. Kataura,et al.  XRD and TEM study of high pressure treated single-walled carbon nanotubes and C60-peapods , 2005 .

[7]  Antonella Macagnano,et al.  A high sensitive NO2 gas sensor based on PEDOT–PSS/TiO2 nanofibres , 2013 .

[8]  Li-Zhen Fan,et al.  High-performance polypyrrole electrode materials for redox supercapacitors , 2006 .

[9]  S. Xiong,et al.  Performance of polymer solar cells fabricated by dip coating process , 2012 .

[10]  Sudha V. Bhoraskar,et al.  Humidity sensing with weak acid-doped polyaniline and its composites , 2003 .

[11]  Eunji Lee,et al.  Enhanced thermoelectric performance of PEDOT:PSS/PANI–CSA polymer multilayer structures , 2016 .

[12]  Shuang Li,et al.  Alternating Stacked Graphene‐Conducting Polymer Compact Films with Ultrahigh Areal and Volumetric Capacitances for High‐Energy Micro‐Supercapacitors , 2015, Advanced materials.

[13]  M. Khakani,et al.  The nanostructure and electrical properties of SWNT bundle networks grown by an ‘all-laser’ growth process for nanoelectronic device applications , 2004 .

[14]  Tai Hyun Park,et al.  Human Dopamine Receptor-Conjugated Multidimensional Conducting Polymer Nanofiber Membrane for Dopamine Detection. , 2016, ACS applied materials & interfaces.

[15]  S. Ramakrishna,et al.  Nanocomposites for electronic applications that can be embedded for textiles and wearables , 2019, Science China Technological Sciences.

[16]  Priyabrata Sadhukhan,et al.  Polyaniline-multiwalled carbon nanotube (PANI-MWCNT): Room temperature resistive carbon monoxide (CO) sensor , 2018, Synthetic Metals.

[17]  Y. Shimizu,et al.  A thick-film impedancemetric carbon monoxide sensor using layered perovskite-type cuprate , 2017 .

[18]  Vinod Kumar,et al.  Polyaniline–Carbon Nanotube Composites: Preparation Methods, Properties, and Applications , 2018 .

[19]  Tara Betts.  Humidity , 1912, Buffalo medical journal.

[20]  J. Jang,et al.  Efficient and moisture-resistant hole transport layer for inverted perovskite solar cells using solution-processed polyaniline , 2018 .

[21]  Sergey A. Piletsky,et al.  Ammonia sensors based on sensitive polyaniline films , 1996 .

[22]  Iole Venditti,et al.  Chemiresistive polyaniline-based gas sensors: A mini review , 2015 .

[23]  D. E. Aston,et al.  X-ray photoelectron spectroscopy analysis for the chemical impact of solvent addition rate on electromagnetic shielding effectiveness of HCl-doped polyaniline nanopowders , 2015 .

[24]  Mauro C. Santos,et al.  Self-assembled films based on polyaniline/multiwalled carbon nanotubes composites and sulphonated polystyrene deposited onto ITO substrates , 2015 .

[25]  J. Nagy,et al.  Ball milling effect on the structure of single-wall carbon nanotubes , 2004 .

[26]  Mary M. Rodgers,et al.  Wearable technologies for active living and rehabilitation: Current research challenges and future opportunities , 2019, Journal of rehabilitation and assistive technologies engineering.

[27]  J. Jang,et al.  A highly sensitive wireless nitrogen dioxide gas sensor based on an organic conductive nanocomposite paste , 2019, Journal of Materials Chemistry A.

[28]  Jihuai Wu,et al.  Preparation of PAA‐g‐PEG/PANI polymer gel electrolyte and its application in quasi solid state dye‐sensitized solar cells , 2015 .

[29]  B. Kharisov,et al.  Methods for dispersion of carbon nanotubes in water and common solvents , 2014 .

[30]  Jung Hwan Park,et al.  Flash‐Induced Stretchable Cu Conductor via Multiscale‐Interfacial Couplings , 2018, Advanced science.

[31]  Jae Young Lee,et al.  Electrochemical deposition of conductive and adhesive polypyrrole-dopamine films , 2016, Scientific Reports.

[32]  Partha Pratim Sengupta,et al.  Polyaniline as a Gas-Sensor Material , 2006 .

[33]  P. Kováčik,et al.  Effect of side groups on the vacuum thermal evaporation of polythiophenes for organic electronics , 2012 .

[34]  Huy L. Nguyen,et al.  Development of interdigitated arrays coated with functional polyaniline/MWCNT for electrochemical biodetection: application for human papilloma virus. , 2011, Talanta.

[35]  Sunghun Cho,et al.  Fabrication of water-dispersible and highly conductive PSS-doped PANI/graphene nanocomposites using a high-molecular weight PSS dopant and their application in H2S detection. , 2014, Nanoscale.

[36]  Sunghun Cho,et al.  Screen-Printable and Flexible RuO2 Nanoparticle-Decorated PEDOT:PSS/Graphene Nanocomposite with Enhanced Electrical and Electrochemical Performances for High-Capacity Supercapacitor. , 2015, ACS applied materials & interfaces.

[37]  K. Hata,et al.  Macroscopic wall number analysis of single-walled, double-walled, and few-walled carbon nanotubes by X-ray diffraction. , 2011, Journal of the American Chemical Society.

[38]  R. Advíncula,et al.  Nanostructuring polymers, colloids, and nanomaterials at the air–water interface through Langmuir and Langmuir–Blodgett techniques , 2011 .

[39]  D. Tasis,et al.  Carbon nanotube–polymer composites: Chemistry, processing, mechanical and electrical properties , 2010 .

[40]  Sunghun Cho,et al.  Comparative Studies on Two-Electrode Symmetric Supercapacitors Based on Polypyrrole:Poly(4-styrenesulfonate) with Different Molecular Weights of Poly(4-styrenesulfonate) , 2019, Polymers.

[41]  J. Jang,et al.  Highly porous structured polyaniline nanocomposites for scalable and flexible high-performance supercapacitors. , 2019, Nanoscale.

[42]  Fei Wei,et al.  Fabrication and characterization of multi-walled carbon nanotubes-based ink , 2005 .

[43]  T. Pichler,et al.  The growth of new extended carbon nanophases from ferrocene inside single‐walled carbon nanotubes , 2017, 1901.08324.

[44]  Rohit Kumar,et al.  Study of vortex glass-liquid transition in superconducting Fe(Te, Se) thin films on LaAlO3 substrates , 2019, Journal of Applied Physics.

[45]  J. Jang,et al.  Low-cost and efficient perovskite solar cells using a surfactant-modified polyaniline:poly(styrenesulfonate) hole transport material , 2017 .

[46]  Reza Ansari,et al.  Polypyrrole Conducting Electroactive Polymers: Synthesis and Stability Studies , 2006 .

[47]  Dermot Diamond,et al.  Humidity sensors based on polyaniline nanofibres , 2010 .

[48]  C. M. Bates,et al.  Rapid and Selective Deposition of Patterned Thin Films on Heterogeneous Substrates via Spin Coating. , 2019, ACS applied materials & interfaces.

[49]  Mohd Nizar Hamidon,et al.  Humidity Sensors Principle, Mechanism, and Fabrication Technologies: A Comprehensive Review , 2014, Sensors.

[50]  Yongsheng Chen,et al.  Noncovalent nanohybrid of ferrocene with single-walled carbon nanotubes and its enhanced electrochemical property , 2006 .

[51]  M. Prato,et al.  Single-wall carbon nanotube-ferrocene nanohybrids: observing intramolecular electron transfer in functionalized SWNTs. , 2003, Angewandte Chemie.

[52]  Liang Li,et al.  Facile preparation of halloysite/polyaniline nanocomposites via in situ polymerization and layer-by-layer assembly with good supercapacitor performance , 2016, Journal of Materials Science.

[53]  Donald W. Brenner,et al.  Mechanical and Electrical Properties of Nanotubes , 2002 .

[54]  K. Hayashi,et al.  Electrochemical deposition of nanostructured polyaniline on an insulating substrate , 2010 .

[55]  D. N. Borisenko,et al.  Thermally stable hydrogen compounds obtained under high pressure on the basis of carbon nanotubes and nanofibers , 2004 .

[56]  U. Sundararaj,et al.  Electrical Permittivity and Electrical Conductivity of Multiwall Carbon Nanotube‐Polyaniline (MWCNT‐PANi) Core‐Shell Nanofibers and MWCNT‐PANi/polystyrene Composites , 2014 .