Microstructure and mechanical properties of laser welded S960 high strength steel

Abstract S960 steel is an advanced low carbon and low alloy ultra-high strength steel (with a minimum yield strength of 960 MPa) developed by Tata Steel. At present, there is a scarcity of data for laser welding of such a material. In this study, 8 mm thick hot rolled and quenched S960 high strength low alloy (HSLA) steel plates were welded using a 16 kW fibre laser system. The microstructure, microhardness, and tensile properties were characterised, Charpy impact testing and three-point bending testing were carried out, and fracture surfaces were investigated. Preliminary results suggest that the laser welding process can produce single-pass welds which are free of macroscopic defects. The microstructures in the fusion zone and heat affected zone were predominately martensite and some self-tempered martensite, with grain size variation in different sub-zones. The tensile properties of the laser welded joint matched those obtained for the base material, with failure occurring in the base material away from the weld. While the welded joint performed well when subjected to bending, the impact toughness was reduced when compared with that of the base material.

[1]  Fang Peng,et al.  Experimental investigation on electroplastic effect of DP980 advanced high strength steel , 2015 .

[2]  M. L. Hamilton,et al.  Effect of specimen size on the impact properties of neutron irradiated A533B steel , 1995 .

[3]  R. Mishra,et al.  Analysis of microstructural evolution during friction stir welding of ultrahigh-strength steel , 2010 .

[4]  Yican Wu,et al.  Microstructure and mechanical properties of the TIG welded joints of fusion CLAM steel , 2010 .

[5]  K. Bang,et al.  Estimation and prediction of HAZ softening in thermomechanically controlled-rolled and accelerated-cooled steel , 2002 .

[6]  V. Balasubramanian,et al.  An assessment of microstructure, hardness, tensile and impact strength of friction stir welded ferritic stainless steel joints , 2010 .

[7]  P. Harrison,et al.  A study concerning intercritical HAZ microstructure and toughness in HSLA steels , 1991 .

[8]  Sangho Kim,et al.  Correlation of the microstructure and fracture toughness of the heat-affected zones of an SA 508 steel , 2000 .

[9]  M. Eroglu,et al.  Effect of chromium on microstructure and toughness of intercritical heat affected zone of low carbon steel , 2002 .

[10]  Wei Yan,et al.  Change of tensile behavior of a high-strength low-alloy steel with tempering temperature , 2009 .

[11]  Xiaozhi Hu,et al.  Effect of buffer layer and notch location on fatigue behavior in welded high-strength low-alloy , 2012 .

[12]  S. H. Seyedein,et al.  Modern fiber laser beam welding of the newly-designed precipitation-strengthened nickel-base superalloys , 2014 .

[13]  M. Sugiyama,et al.  Abnormal α to γ Transformation Behavior of Steels with a Martensite and Bainite Microstructure at a Slow Reheating Rate , 2009 .

[14]  J. Coupland,et al.  Numerical simulation of alloy composition in dissimilar laser welding , 2015 .

[15]  B. Bezenšek,et al.  The toughness of laser welded joints in the ductile–brittle transition , 2007 .

[16]  B. M. Patchett,et al.  Estimation of cooling rate in the welding of plates with intermediate thickness , 2005 .

[17]  Jeong Hun Lee,et al.  Laser, tungsten inert gas, and metal active gas welding of DP780 steel: Comparison of hardness, tensile properties and fatigue resistance , 2014 .

[18]  F. Minami,et al.  Evaluation method for Charpy impact toughness of laser welds based on lateral contraction analysis , 2011, Welding in the World.

[19]  Şükrü Talaş,et al.  The assessment of carbon equivalent formulas in predicting the properties of steel weld metals , 2010 .

[20]  S. Nemecek,et al.  Differences between Laser and Arc Welding of HSS Steels , 2012 .

[21]  J. Onõro,et al.  Fatigue behaviour of laser welds of high-strength low-alloy steels , 1997 .

[22]  Lin Li,et al.  Gap-free fibre laser welding of Zn-coated steel on Al alloy for light-weight automotive applications , 2011 .

[23]  D. Viano,et al.  Influence of heat input and travel speed on microstructure and mechanical properties of double tandem submerged arc high strength low alloy steel weldments , 2000 .

[24]  L. Du,et al.  Analysis of microstructural variation and mechanical behaviors in submerged arc welded joint of high strength low carbon bainitic steel , 2012 .

[25]  Priti Wanjara,et al.  Hybrid fiber laser – Arc welding of thick section high strength low alloy steel , 2011 .

[26]  Guodong Zhang,et al.  Enhancement of mechanical properties and failure mechanism of electron beam welded 300M ultrahigh strength steel joints , 2013 .

[27]  W. R. Corwin,et al.  The use of small scale specimens for testing irradiated materials , 1986 .

[28]  B. M. Patchett,et al.  Transformation twins in the weld HAZ of a low-carbon high-strength microalloyed steel , 2006 .

[29]  M. Naderi,et al.  A comparative study of the microstructure and mechanical properties of HTLA steel welds obtained by the tungsten arc welding and resistance spot welding , 2012 .

[30]  K. Wallin.  Upper shelf energy normalisation for sub-sized Charpy-V specimens , 2001 .

[31]  J. Yoon,et al.  Characterization of high strength and high toughness Ni―Mo―Cr low alloy steels for nuclear application , 2010 .

[32]  C. Bayley,et al.  Influence of Weld Heat Input on the Fracture and Metallurgy of HSLA-65 , 2009 .

[33]  G. Madhusudhan Reddy,et al.  Microstructure and residual stress distribution of similar and dissimilar electron beam welds ― Maraging steel to medium alloy medium carbon steel , 2010 .

[34]  S. Elliott.  ELECTRON BEAM WELDING OF C/MN STEELS -- TOUGHNESS AND FATIGUE PROPERTIES , 1984 .

[35]  F. Minami,et al.  Fracture Toughness Evaluation of Laser Beam-Welded Joints of 780 MPa-Strength Class Steel , 2009 .

[36]  M. L. Hamilton,et al.  The influence of specimen size on charpy impact testing of unirradiated HT-9 , 1988 .

[37]  Ming Gao,et al.  Weld formation mechanism of fiber laser oscillating welding of austenitic stainless steel , 2015 .

[38]  J. Kömi,et al.  Laser and laser gas-metal-arc hybrid welding of 960 MPa direct-quenched structural steel in a butt joint configuration , 2015 .

[39]  Yuh J. Chao,et al.  Charpy impact energy, fracture toughness and ductile–brittle transition temperature of dual-phase 590 Steel , 2007 .