Numerical prediction of heat affected layer in the EDM of aeronautical alloys

Abstract Electrical discharge machining is a popular non-traditional machining process, optimum for accurate machining of complex geometries in hard materials. EDM has been used for decades for machining pieces for the aeronautical industry, but surface integrity, and consequently the reliability of the machined parts have been questioned for long time due to the thermal nature of this machining process. In recent years, efforts have been put on modeling of the EDM process, being thermal modeling of the process one promising alternative. In a previous publication an original model of the EDM process was presented and it was used to predict material removal rate and surface finish for the EDM of steel. In the present article the capability of that modeling tool to characterize discharge properties and to predict recast layer distribution when EDMing an aeronautical alloy will be analyzed. EDM process of Inconel 718 has been studied and discharge properties have been obtained for four different EDM regimes. The capability of the model to reflect the behavior of more energetic regimes is discussed. Gathered information has been used to simulate the evolution of the recast layer generation process. Obtained results have been validated comparing them with experimental measurements, revealing a good correlation between predictions and experimental data. Finally, energetic efficiency of the discharge process has been simulated for the adjusted EDM regimes.

[1]  Naotake Mohri,et al.  A Study on Single Discharge Machining with Low Melting Temperature Alloy , 2004 .

[2]  R. Flükiger,et al.  Properties of the plasma channel in liquid discharges inferred from cathode local temperature measurements , 2005 .

[3]  Keith Ridgway,et al.  Workpiece Surface Integrity and Tool Life Issues When Turning Inconel 718™ Nickel Based Superalloy , 2004 .

[4]  A. Erden.  Effect of Materials on the Mechanism of Electric Discharge Machining (E.D.M.) , 1983 .

[5]  F. Klocke,et al.  EDM simulation: finite element-based calculation of deformation, microstructure and residual stresses , 2003 .

[6]  Stephen T. Newman,et al.  State of the art electrical discharge machining (EDM) , 2003 .

[7]  S. Yeo,et al.  Modelling of overlapping craters in micro-electrical discharge machining , 2008 .

[8]  Shreyes N. Melkote,et al.  Investigation of the effect of process parameters on the formation and characteristics of recast layer in wire-EDM of Inconel 718 , 2009 .

[9]  Masanori Kunieda,et al.  Simulation of Die-Sinking EDM by Discharge Location Searching Algorithm , 1998 .

[10]  Werner Theisen,et al.  Electro discharge machining of nickel–titanium shape memory alloys , 2004 .

[11]  Biing-Hwa Yan,et al.  EDM performance of Cr/Cu-based composite electrodes , 2003 .

[12]  Che-Chung Wang,et al.  Recast layer removal after electrical discharge machining via Taguchi analysis: A feasibility study , 2009 .

[13]  R. Ramakrishnan,et al.  Modeling and multi-response optimization of Inconel 718 on machining of CNC WEDM process , 2008 .

[14]  Song Huat Yeo,et al.  Electro-thermal modelling of anode and cathode in micro-EDM , 2007 .

[15]  David K. Aspinwall,et al.  Workpiece surface roughness and integrity after WEDM of Ti–6Al–4V and Inconel 718 using minimum damage generator technology , 2008 .

[16]  Itziar Cabanes,et al.  Computer simulation of performance of electrical discharge machining operations , 2009, Int. J. Comput. Integr. Manuf..

[17]  Baoping Cai,et al.  Study of the recast layer of a surface machined by sinking electrical discharge machining using water-in-oil emulsion as dielectric , 2011 .

[18]  José Antonio Sánchez,et al.  A numerical model of the EDM process considering the effect of multiple discharges , 2009 .

[19]  Bülent Ekmekci,et al.  Residual stresses and white layer in electric discharge machining (EDM) , 2007 .

[20]  P. C. Pandey,et al.  Analysis and modelling of edm parameters , 1982 .

[21]  O. A. Abu Zeid,et al.  On the effect of electrodischarge machining parameters on the fatigue life of AISI D6 tool steel , 1997 .

[22]  L. I. Sharakhovsky,et al.  Model of workpiece erosion for electrical discharge machining process , 2006 .