A Numerical Study of the Stress-Strain Behavior of Additively Manufactured Aluminum-Silicon Alloy at the Scale of Dendritic Structure

[1]  F. Berto,et al.  Porosity Inducing Process Parameters in Selective Laser Melted AlSi10Mg Aluminium Alloy , 2020 .

[2]  V. Romanova,et al.  Formation of Bulk Tensile Regions in Metal Matrix Composites and Coatings under Uniaxial and Multiaxial Compression , 2020 .

[3]  Rui Huang,et al.  Effect of In-Situ Laser Remelting on the Microstructure of SS316L Fabricated by Micro Selective Laser Melting , 2019, Lecture Notes in Mechanical Engineering.

[4]  V. Romanova,et al.  ON THE PROBLEM OF STRAIN LOCALIZATION AND FRACTURE SITE PREDICTION IN MATERIALS WITH IRREGULAR GEOMETRY OF INTERFACES , 2019, Facta Universitatis, Series: Mechanical Engineering.

[5]  S. Schmauder,et al.  A numerical study of plastic strain localization and fracture across multiple spatial scales in materials with metal-matrix composite coatings , 2019, Theoretical and Applied Fracture Mechanics.

[6]  T. Maeshima,et al.  Solute clustering and supersaturated solid solution of AlSi10Mg alloy fabricated by selective laser melting , 2019, Heliyon.

[7]  Annalisa Pola,et al.  Study of heat treatment parameters for additively manufactured AlSi10Mg in comparison with corresponding cast alloy , 2019 .

[8]  M. Khimich,et al.  Selection of Technological Parameters of Selective Laser Melting of Mechanocomposite Ti–Nb Powder , 2019, Inorganic Materials: Applied Research.

[9]  Jian Li,et al.  Columnar to equiaxed transition during direct metal laser sintering of AlSi10Mg alloy: Effect of building direction , 2018, Additive Manufacturing.

[10]  V. Egorushkin,et al.  Lattice Curvature, Shear Bands, and Electroplastic Effect , 2018, Physical Mesomechanics.

[11]  V. Panin,et al.  Lattice Curvature and Mesoscopic Strain-Induced Defects as the Basis of Plastic Deformation in Ultrafine-Grained Metals , 2018, Physical Mesomechanics.

[12]  J. S. Zuback,et al.  Additive manufacturing of metallic components – Process, structure and properties , 2018 .

[13]  J. Eckert,et al.  Microstructure and mechanical properties of a heat-treatable Al-3.5Cu-1.5Mg-1Si alloy produced by selective laser melting , 2018 .

[14]  W. Woo,et al.  Evaluation of the stress-strain relationship of constituent phases in AlSi10Mg alloy produced by selective laser melting using crystal plasticity FEM , 2017 .

[15]  Francesco Trevisan,et al.  On the Selective Laser Melting (SLM) of the AlSi10Mg Alloy: Process, Microstructure, and Mechanical Properties , 2017, Materials.

[16]  J. Kruth,et al.  Fine-structured aluminium products with controllable texture by selective laser melting of pre-alloyed AlSi10Mg powder , 2013 .

[17]  E. Brandl,et al.  Additive manufactured AlSi10Mg samples using Selective Laser Melting (SLM): Microstructure, high cycle fatigue, and fracture behavior , 2012 .

[18]  Jyoti Mazumder,et al.  Evolution of microstructure in laser deposited Al-11.28%Si alloy , 2012 .

[19]  Z. Zhang,et al.  Tensile properties and fracture mechanism of Al–Mg alloy subjected to equal channel angular pressing , 2007 .

[20]  P. Turchi,et al.  Simulations of the mechanical properties of crystalline, nanocrystalline, and amorphous SiC and Si , 2007 .

[21]  E. Werner,et al.  Additive Manufacturing: A Review of the Influence of Building Orientation and Post Heat Treatment on the Mechanical Properties of Aluminium Alloys , 2019, Advanced Structured Materials.

[22]  Mengyun Liu.  Quench sensitivity of high pressure vacuum die castings and permanent mold castings of Aural-3/5 alloys , 2018 .

[23]  Brian A. Nosek,et al.  Mechanical properties and microstructure of AlSi10Mg alloy obtained by casting and SLM technique , 2018 .