Relative performance of a vibratory energy harvester in mono- and bi-stable potentials

Motivated by the need for broadband vibratory energy harvesting, many research studies have recently proposed energy harvesters with nonlinear characteristics. Based on the shape of their potential function, such devices are classified as either mono- or bi-stable energy harvesters. This paper aims to investigate the relative performance of these two classes under similar excitations and electric loading conditions. To achieve this goal, an energy harvester consisting of a clamped–clamped piezoelectric beam bi-morph is considered. The shape of the harvester's potential function is altered by applying a static compressive axial load at one end of the beam. This permits operation in the mono-stable (pre-buckling) and bi-stable (post-buckling) configurations. For the purpose of performance comparison, the axial load is used to tune the harvester's oscillation frequencies around the static equilibria such that they have equal values in the mono- and bi-stable configurations. The harvester is subjected to harmonic base excitations of different magnitudes and a slowly varying frequency spanning a wide band around the tuned oscillation frequency. The output voltage measured across a purely resistive load is compared over the frequency range considered. Two cases are discussed; the first compares the performance when the bi-stable harvester has deep potential wells, while the second treats a bi-stable harvester with shallow wells. Both numerical and experimental results demonstrate the essential role that the potential shape plays in conjunction with the base acceleration to determine whether the bi-stable harvester can outperform the mono-stable one and for what range of frequencies. Results also illustrate that, for a bi-stable harvester with shallow potential wells, super-harmonic resonances can activate the inter-well dynamics even for a small base acceleration, thereby producing large voltages in the low frequency range.

[1]  Mohammed F. Daqaq,et al.  Electromechanical Modeling and Nonlinear Analysis of Axially Loaded Energy Harvesters , 2011 .

[2]  N. G. Stephen,et al.  On energy harvesting from ambient vibration , 2006 .

[3]  Jan M. Rabaey,et al.  A study of low level vibrations as a power source for wireless sensor nodes , 2003, Comput. Commun..

[4]  B. Mann,et al.  Nonlinear dynamics for broadband energy harvesting: Investigation of a bistable piezoelectric inertial generator , 2010 .

[5]  Wen-Jong Wu,et al.  Tunable resonant frequency power harvesting devices , 2006, SPIE Smart Structures and Materials + Nondestructive Evaluation and Health Monitoring.

[6]  Mohammed F. Daqaq,et al.  Response of uni-modal duffing-type harvesters to random forced excitations , 2010 .

[7]  Brian P. Mann,et al.  Investigations of a nonlinear energy harvester with a bistable potential well , 2010 .

[8]  L. Gammaitoni,et al.  Nonlinear energy harvesting. , 2008, Physical review letters.

[9]  Daniel J. Inman,et al.  Towards autonomous sensing , 2006, SPIE Smart Structures and Materials + Nondestructive Evaluation and Health Monitoring.

[10]  Lawrence N. Virgin,et al.  Vibration of Axially-Loaded Structures , 2007 .

[11]  Daniel J. Inman,et al.  A Distributed Parameter Electromechanical Model for Cantilevered Piezoelectric Energy Harvesters , 2008 .

[12]  Colin R. McInnes,et al.  Enhanced Vibrational Energy Harvesting Using Non-linear Stochastic Resonance , 2008 .

[13]  D. Inman,et al.  A Review of Power Harvesting from Vibration using Piezoelectric Materials , 2004 .

[14]  Shadrach Roundy,et al.  On the Effectiveness of Vibration-based Energy Harvesting , 2005 .

[15]  Massimo Ruzzene,et al.  . Proceedings of IDETC/CIE 2007, ASME 2007 International Design Engineering Technical Conferences & Computers and Information in Engineering Conference, Las Vegas NV, USA , 2007 .

[16]  Wouter Bracke.  Generic Architectures and Design Methods for Autonomous Sensors (Generische architecturen en ontwerpmethodes voor autonome sensoren) , 2006 .

[17]  David A W Barton,et al.  Energy harvesting from vibrations with a nonlinear oscillator , 2010 .

[18]  B. Mann,et al.  Reversible hysteresis for broadband magnetopiezoelastic energy harvesting , 2009 .

[19]  S. Shahruz.  Design of mechanical band-pass filters for energy scavenging , 2006 .

[20]  Noël E. Dutoit,et al.  Experimental Verification of Models for Microfabricated Piezoelectric Vibration Energy Harvesters , 2007 .

[21]  Jin Liu,et al.  2.45 GHz power and data transmission for a low-power autonomous sensors platform , 2004, Proceedings of the 2004 International Symposium on Low Power Electronics and Design (IEEE Cat. No.04TH8758).

[22]  Refet Firat Yazicioglu,et al.  Technologies for highly miniaturized autonomous sensor networks , 2006, Microelectron. J..

[23]  Daniel J. Inman,et al.  Generation and Storage of Electricity from Power Harvesting Devices , 2005 .

[24]  Joseph A. Paradiso,et al.  Energy scavenging for mobile and wireless electronics , 2005, IEEE Pervasive Computing.

[25]  Makoto Ishida,et al.  Integrated Inductors for RF Transmitters in CMOS/MEMS Smart Microsensor Systems , 2007, Sensors (Basel, Switzerland).

[26]  Paul K. Wright,et al.  A piezoelectric vibration based generator for wireless electronics , 2004 .

[27]  M. G. Prasad,et al.  A vibration energy harvesting device with bidirectional resonance frequency tunability , 2008 .

[28]  Yang Zhang,et al.  Toward self-tuning adaptive vibration-based microgenerators , 2005, SPIE Micro + Nano Materials, Devices, and Applications.

[29]  P. Wright,et al.  Resonance tuning of piezoelectric vibration energy scavenging generators using compressive axial preload , 2006 .