Approaching Mixed Elastohydrodynamic Lubrication of Smooth Journal-Bearing Systems with Low Rotating Speed

When a conformal interface is under low velocity and heavy load conditions, solid contact (or dry contact) may occur even in a system with smooth surfaces. This paper presents two approaches for solving steady-state and transient mixed elastohydrodynamic lubrication problems of journal bearings with smooth surfaces under low rotating speed. The first approach uses the reduced Reynolds equation with a combined finite element–backward finite difference scheme and the second applies a zero film thickness equation to describe the mechanical behavior of mating surfaces at solid contact points. The major advantages of these two approaches are (1) no division of the solution domain into a lubricated area and a solid contact area is necessary and (2) the solid contact pressure, lubricant pressure, and eccentricity ratio can be solved simultaneously. Numerical examples are presented for the application of these approaches. For the steady-state cases under low velocity studied in this work, pressure distributions approach those found in a dry contact state. This comparison confirms that the contact treatments are proper. Moreover, a transient case under sinusoidal loading was analyzed with these two approaches, and the results showed good agreement. This comparison further supports the use of these approaches. Presented at the STLE Annual Meeting in Las Vegas, Nevada May 15-19, 2005 Review led by Alan Lebeck

[1]  R. F. Salant,et al.  Numerical Study of a Rotary Lip Seal With a Quasi-Random Sealing Surface , 2001 .

[2]  J. J. Kalker,et al.  Variational principles of contact elastostatics , 1977 .

[3]  Warren Bower.  New directions , 1937 .

[4]  Shangwu Xiong,et al.  Finite element method for mixed elastohydrodynamic lubrication of journal‐bearing systems , 2004 .

[5]  Farshid Sadeghi,et al.  Analysis of EHL Circular Contact Shut Down , 2003 .

[6]  Chih Lin,et al.  Mixed Lubrication of Coupled Journal-Thrust Bearing Systems , 2002 .

[7]  H. Cheng,et al.  An Average Flow Model for Determining Effects of Three-Dimensional Roughness on Partial Hydrodynamic Lubrication , 1978 .

[8]  K. P. Oh.  The Numerical Solution of Dynamically Loaded Elastohydrodynamic Contact as a Nonlinear Complementarity Problem , 1984 .

[9]  Dong Zhu,et al.  A Full Numerical Solution to the Mixed Lubrication in Point Contacts , 2000 .

[10]  Richard F. Salant,et al.  A mixed soft elastohydrodynamic lubrication model with interasperity cavitation and surface shear deformation , 2000 .

[11]  D. Dowson.  Boundary and mixed lubrication : science and applications : proceedings of the 28th Leeds-Lyon Symposium on Tribology held in the Messe Congress Center, Vienna,Austria, 4th-7th September, 2001 , 2002 .

[12]  Chih Lin,et al.  A mixed-TEHD analysis and experiment of journal bearings under severe operating conditions , 2002 .

[13]  K. Johnson.  Contact Mechanics: Frontmatter , 1985 .

[14]  Qian Wang,et al.  A Mixed-TEHD Model for Journal-Bearing Conformal Contacts—Part I: Model Formulation and Approximation of Heat Transfer Considering Asperity Contact , 1997 .

[15]  Chih Lin,et al.  Mixed Lubrication of Coupled Journal-Thrust-Bearing Systems Including Mass Conserving Cavitation , 2003 .

[16]  Farshid Sadeghi,et al.  Analysis of EHL Circular Contact Start Up: Part I—Mixed Contact Model With Pressure and Film Thickness Results , 2001 .

[17]  Qian Wang,et al.  A Mixed-TEHD Model for Journal-Bearing Conformal Contact—Part II: Contact, Film Thickness, and Performance Analyses , 1997 .

[18]  J. F. Archard,et al.  Lubrication at point contacts , 1961, Proceedings of the Royal Society of London. Series A. Mathematical and Physical Sciences.

[19]  Qian Wang,et al.  A Mixed-Lubrication Study of Journal Bearing Conformal Contacts , 1996 .

[20]  J. Barbera,et al.  Contact mechanics , 1999 .