Stiffness tailoring of elliptical composite cylinders for axial buckling performance

Abstract Automated fiber placement (AFP) machines have made it possible to tailor the material stiffness properties in a laminated composite structure by fiber steering. The so-called variable stiffness (VS) laminate can be designed to improve the structural performance of a composite component. Herein, using a metamodeling based design optimization (MBDO) method, elliptical composite cylinders with VS laminate are designed and optimized for maximum axial buckling capacity. The effect of cross-sectional aspect ratio of the elliptical cylinders on the potential improvement of the buckling capacity is also investigated. As the baseline for comparison, for each cross-sectional aspect ratio, the buckling capacity of elliptical cylinders with quasi-isotropic (QI) and optimum constant stiffness (CS) laminates are also calculated. It is found that the buckling capacity of an elliptical composite cylinder can be improved by fiber steering up to 118% compared with its best CS counterpart.

[1]  Rakesh K. Kapania,et al.  Buckling and Static Analysis of Curvilinearly Stiffened Plates Using Mesh-Free Method , 2009 .

[2]  K. Potter,et al.  The engineering aspects of automated prepreg layup: History, present and future , 2012 .

[3]  Zafer Gürdal,et al.  Circumferential stiffness tailoring of general cross section cylinders for maximum buckling load with strength constraints , 2012 .

[4]  Paul M. Weaver,et al.  Continuous tow shearing for manufacturing variable angle tow composites , 2012 .

[5]  Mohammad Rouhi,et al.  Multi-objective design optimization of variable stiffness composite cylinders , 2015 .

[6]  Paul M. Weaver,et al.  Limitations of fibre placement techniques for variable angle tow composites and their process-induced defects , 2011 .

[7]  Suong V. Hoa,et al.  Effect of structural parameters on design of variable-stiffness composite cylinders made by fiber steering , 2014 .

[8]  Paul M. Weaver,et al.  Bend-free shells under uniform pressure with variable-angle tow derived anisotropy , 2012 .

[9]  Zafer Gürdal,et al.  Optimization of a composite cylinder under bending by tailoring stiffness properties in circumferential direction , 2010 .

[10]  B. Tatting,et al.  Analysis and design of variable stiffness composite cylinders , 1998 .

[11]  Paul M. Weaver,et al.  Initial post-buckling of variable-stiffness curved panels , 2014 .

[12]  Raphael T. Haftka,et al.  Surrogate-based Analysis and Optimization , 2005 .

[13]  Zafer Gürdal,et al.  Optimum tailoring of fibre-steered longitudinally stiffened cylinders , 2015 .

[14]  Maurizio Paschero,et al.  Improvement of Axial Buckling Capacity of Elliptical Lattice Cylinders , 2010 .

[15]  Michael W. Hyer,et al.  Use of Material Tailoring to Improve Buckling Capacity of Elliptical Composite Cylinders , 2007 .

[16]  M. Hyer,et al.  Improvement of Axial Load Capacity of Elliptical Cylindrical Shells , 2009 .

[17]  Mohammad Rouhi,et al.  The effect of the percentage of steered plies on the bending-induced buckling performance of a variable stiffness composite cylinder , 2015 .

[18]  Zafer Gurdal,et al.  A Theoretical Model to Study the Influence of Tow-drop Areas on the Stiffness and Strength of Variable-stiffness Laminates , 2009 .

[19]  Paul M. Weaver,et al.  Anisotropy-Induced Spiral Buckling in Compression-Loaded Cylindrical Shells , 2002 .

[20]  K. Wu,et al.  Post-buckling analyses of variable-stiffness composite cylinders in axial compression , 2015 .

[21]  M. Hyer,et al.  Fundamental Frequencies of Elliptical Composite Cylinders with Circumferentially Varying Fiber Orientation , 2012 .

[22]  G. Gary Wang,et al.  Review of Metamodeling Techniques in Support of Engineering Design Optimization , 2007, DAC 2006.

[23]  Paul M. Weaver,et al.  Postbuckling analysis of variable angle tow composite plates under shear load , 2013 .