Estimation of rotor position in a three-phase SRM at standstill and low speeds

Switched reluctance motors (SRMs) are widely employed as industrial drives because they are inexpensive, simple, and sturdy, and further, they deliver a robust and reliable performance. SRMs are controlled with a rotor position sensor attached to the motor shaft. Normally, encoders, resolvers, or Hall sensors are used as position sensors. The use of these sensors, however, increases the size and cost of the machine and degrades its performance. Therefore, to overcome these difficulties, several sensorless drive techniques have been reported. This paper presents a method for estimating the position of a rotor in an SRM, based on calculation of the space vector of the phase inductance at standstill and low speeds. The position at standstill is obtained simply without making use of the magnetic characteristics of the motor or any additional hardware. Assuming the inductance waveform to be a sine wave, the position of the rotor at standstill is obtained from the phase inductance vectors of all phases. At low speeds, position estimation is carried out by applying a DC link voltage to the unenergized phases. The validity of the proposed method is experimentally verified. © 2011 Wiley Periodicals, Inc. Electr Eng Jpn, 178(2): 55–63, 2012; Published online in Wiley Online Library (wileyonlinelibrary.com). DOI 10.1002/eej.21205

[1]  Nobuyuki Matsui,et al.  Position Sensorless Drive of SRM Mounted on Hydraulic Pump Unit. , 2003 .

[2]  S.R. MacMinn,et al.  Flux-current methods for SRM rotor position estimation , 1991, Conference Record of the 1991 IEEE Industry Applications Society Annual Meeting.

[3]  J.H. Lang,et al.  A simple motion estimator for variable-reluctance motors , 1988, Conference Record of the 1988 IEEE Industry Applications Society Annual Meeting.

[4]  R. D. Lorenz,et al.  Sensorless control of a SRM at low speeds and standstill based on signal power evaluation , 1998, IECON '98. Proceedings of the 24th Annual Conference of the IEEE Industrial Electronics Society (Cat. No.98CH36200).

[5]  B. Fahimi,et al.  Prediction of rotor position at standstill and rotating shaft conditions in switched reluctance machines , 2006, IEEE Transactions on Power Electronics.

[6]  F. R. Salmasi,et al.  Sensorless control of SRM at standstill , 2001, APEC 2001. Sixteenth Annual IEEE Applied Power Electronics Conference and Exposition (Cat. No.01CH37181).

[7]  Longya Xu,et al.  Eliminating starting hesitation for reliable sensorless control of switched reluctance motors , 1998, Conference Record of 1998 IEEE Industry Applications Conference. Thirty-Third IAS Annual Meeting (Cat. No.98CH36242).

[8]  M. Ehsani,et al.  Inductance model-based sensorless control of the switched reluctance motor drive at low speed , 2004, IEEE Transactions on Power Electronics.

[9]  R. Krishnan,et al.  Switched reluctance motor drives : modeling, simulation, analysis, design, and applications , 2001 .

[10]  Nobuyuki Matsui,et al.  Developing a sensorless approach for switched reluctance motors from a new analytical model , 1999, Conference Record of the 1999 IEEE Industry Applications Conference. Thirty-Forth IAS Annual Meeting (Cat. No.99CH36370).

[11]  I. Miki,et al.  Estimation of Rotor Position for Switched Reluctance Motor at Standstill , 2007, 2007 Power Conversion Conference - Nagoya.

[12]  Longya Xu,et al.  Accurate rotor position detection and sensorless control of SRM for super-high speed operation , 2002 .

[13]  Ichiro Miki,et al.  A Position Sensorless Control Method for SRM Based on Variation of Phase Inductance , 2007 .

[14]  G. Gallegos-Lopez,et al.  High-grade position estimation for SRM drives using flux linkage/current correction model , 1998, Conference Record of 1998 IEEE Industry Applications Conference. Thirty-Third IAS Annual Meeting (Cat. No.98CH36242).