The effects of SEBS-g-maleic anhydride reaction on the morphology and properties of polypropylene/PA6/SEBS ternary blends

Abstract Ternary blends, based on 70% by weight of polypropylene (PP) with 30% by weight of a dispersed phase, consisting of 15% polyamide-6 (PA6) and 15% of a mixture comprising varying ratios of an unreactive poly[styrene- b -(ethylene- co -butylene)- b -styrene] (SEBS) triblock copolymer and a reactive maleic anhydride-grafted SEBS- g -MA, were produced via melt blending in a co-rotating twin-screw extruder. TEM revealed the blend containing only non-reactive SEBS to exhibit individual PA6 and SEBS dispersed phases. However, the progressive replacement of SEBS with reactive SEBS- g -MA increased the degree of interfacial reaction between the SEBS and PA6 phases, thus reducing interfacial tension and providing a driving force for encapsulation of the PA6 by the SEBS. Consequently, the dispersed-phase morphology was observed to transform from two separate phases to acorn-type composite particles, then to individual core-shell particles and finally to agglomerates of the core-shell particles. The resultant blends exhibited significant morphology-induced variations in both thermal and mechanical properties. DSC showed that blends in which the diameter of the PA6 particles was reduced to ≤3 μm by the increasing interfacial reaction exhibited fractionated PA6 crystallisation. In general, mechanical testing showed the blends to exhibit inferior low-strain tensile properties (modulus and yield stress) compared to the matrix PP, but superior ultimate tensile properties (stress and strain at break) and impact strength. These changes are discussed with reference to composite models.

[1]  A. Müller,et al.  Fractionated crystallisation of polyethylene and ethylene/α-olefin copolymers dispersed in immiscible polystyrene matrices , 1999 .

[2]  B. Ohlsson,et al.  Improved compatibility between polyamide and polypropylene by the use of maleic anhydride grafted SEBS , 1998 .

[3]  V. H. Watkins,et al.  Effect of interfacial forces on polymer blend morphologies , 1988 .

[4]  Robert Jérôme,et al.  Strategies for compatibilization of polymer blends , 1998 .

[5]  A. Luciani,et al.  Interfacial tension in polymer blends , 1998 .

[6]  Peter Van Puyvelde,et al.  Rheology and morphology of compatibilized polymer blends , 2001 .

[7]  M. Narkis,et al.  Polymer encapsulation of glass filler in ternary PP/PA‐6/glass blends , 1996 .

[8]  S. Ali,et al.  Effect of silane-based filler surface treatment formulation on the interfacial properties of impact modified polypropylene/magnesium hydroxide composites , 1998 .

[9]  N. Platé,et al.  Reactions in polymer blends: interchain effects and theoretical problems , 2002 .

[10]  G. Michler,et al.  Micromechanical deformation processes in toughened and particle filled semicrystalline polymers: Part 2. model representation for micromechanical deformation processes , 1998 .

[11]  P. Hornsby,et al.  Microstructure and mechanical properties of ternary phase polypropylene/elastomer/magnesium hydroxide fire-retardant compositions , 1996 .

[12]  K. Dedecker,et al.  Reactive compatibilisation of A/(B/C) polymer blends. Part 2. Analysis of the phase inversion region and the co-continuous phase morphology , 1998 .

[13]  V. M. Harding,et al.  Phase structure in polypropylene/PA6/SEBS blends , 1999 .

[14]  B. Pukánszky,et al.  Polypropylene composites. II: Structure-property relationships in two- and three-component polypropylene composites , 1992 .

[15]  D. R. Paul,et al.  Impact-modified nylon 6/polypropylene blends: 1. Morphology-property relationships , 1995 .

[16]  R. Landel,et al.  Mechanical Properties of Polymers and Composites , 1993 .

[17]  J. Seppälä,et al.  Effects of compatibilization on fractionated crystallization of PA6/PP blends , 1993 .

[18]  B. D. Favis,et al.  Factors influencing encapsulation behavior in composite droplet-type polymer blends , 2003 .

[19]  C. Macosko,et al.  Kinetics of amine‐cyclic anhydride reactions in moderately polar solutions , 1995 .

[20]  J. Månson,et al.  Influence of hyperbranched polymers on the interfacial tension of polypropylene/polyamide‐6 blends , 1999 .

[21]  D. Meier,et al.  Prediction and manipulation of the phase morphologies of multiphase polymer blends: II. Quaternary systems , 1997 .

[22]  R. Mülhaupt,et al.  Influence of morphology on the toughening mechanisms of polypropylene modified with core-shell particles derived from thermoplastic elastomers. , 1998 .

[23]  J. Dam,et al.  Co-continuous morphologies in polymer blends with SEBS block copolymers , 1999 .

[24]  D. R. Paul,et al.  Property and morphology relationships for ternary blends of polycarbonate, brittle polymers and an impact modifier , 1992 .

[25]  The annealing and thermal analysis of poly(butylene terephthalate) , 1994 .

[26]  R. Mülhaupt,et al.  Comparison of maleic anhydride-grafted poly(propylene) with maleic anhydride-grafted polystyrene-block-poly(ethene-co-but-1-ene)-block-polystyrene as blend compatibilizers of poly(propylene)/polyamide-6 blends , 1993 .

[27]  Jung-Ki Park,et al.  Concurrent crystallization in polypropylene/nylon‐6 blends using maleic anhydride grafted polypropylene as a compatibilizing agent , 1994 .

[28]  J. Kressler,et al.  Surface Tension Measurements on Ethene−Butene Random Copolymers and Different Polypropenes , 2000 .

[29]  J. Rösch.  Modeling the mechanical properties in polypropylene/polyamide‐6 blends with core shell morphology , 1995 .

[30]  B. Hsiao,et al.  Time-resolved X-ray study of poly(aryl ether ether ketone) crystallization and melting behaviour: 2. Melting , 1993 .

[31]  J. Trent.  Ruthenium tetraoxide staining of polymers: new preparative methods for electron microscopy , 1984 .

[32]  R. Mülhaupt,et al.  Influence of thermoplastic elastomers on mechanical properties and morphologies of isotactic polypropene/glass bead Hybrid composites , 1996 .

[33]  Y. M. Lee,et al.  Compatibilizing effect of maleic anhydride functionalized SEBS triblock elastomer through a reaction induced phase formation in the blends of polyamide6 and polycarbonate: 2. Mechanical properties , 1997 .

[34]  G. Michler,et al.  Micromechanical deformation processes in toughened and particle-filled semicrystalline polymers: Part 1. Characterization of deformation processes in dependence on phase morphology , 1998 .

[35]  C. Macosko.  Morphology development and control in immiscible polymer blends , 2000 .

[36]  K. Yase,et al.  Morphology Development through an Interfacial Reaction in Ternary Immiscible Polymer Blends , 1997 .

[37]  J. Seppälä,et al.  Effects of compatibilizers on the properties of polyamide/polypropylene blends , 1992 .

[38]  A. Müller,et al.  Evaluation of the fractionated crystallization of dispersed polyolefins in a polystyrene matrix , 1998 .

[39]  J. Kolar̆ík,et al.  Ternary composites of polypropylene/elastomer/calcium carbonate: effect of functionalized components on phase structure and mechanical properties , 1992 .