Burrs—Analysis, control and removal

Increasing demands on function and performance call for burr-free workpiece edges after machining. Since deburring is a costly and non-value-added operation, the understanding and control of burr formation is a research topic with high relevance to industrial applications. Following a review of burr classifications along with the corresponding measurement technologies, burr formation mechanisms in machining are described. Deburring and burr control are two possible ways to deal with burrs. For both, an insight into current research results are presented. Finally, a number of case studies on burr formation, control and deburring along with their economic implications are presented.

[1]  S. Kawamura,et al.  Formation and growing up process of grinding burrs , 1989 .

[2]  S. W. Park,et al.  Development of an Effective Measurement System for Burr Geometry , 2006 .

[3]  Pedro J. Arrazola.  Assessment of Deburring Costs in Industrial Case Studies , 2010 .

[4]  S. Basavarajappa,et al.  Analysis of burr formation during drilling of hybrid metal matrix composites using design of experiments , 2006 .

[5]  Reinhard Nothnagel,et al.  DEVELOPMENT OF A HIGH-SPEED-DEBURRING TOOL , 2004 .

[6]  D. Dornfeld,et al.  Modeling of Inter-Layer Gap Formation in Drilling of a Multi-Layered Material , 2003 .

[7]  Y Nakao,et al.  Measurements and Evaluations of Drilling Burr Profile , 2006 .

[8]  David Dornfeld,et al.  Back Cutting and Tool Wear Influence on Burrs in Face Milling - Analysis and Solutions , 2004 .

[9]  Gwo-Lianq Chern,et al.  Study on mechanisms of burr formation and edge breakout near the exit of orthogonal cutting , 2006 .

[10]  David Dornfeld,et al.  Burr/Breakout Model Development and Experimental Verification , 1996 .

[11]  Sangkee Min,et al.  Finite Element Modeling of Burr Formation in Drilling of a Multi-Layered Material , 2004 .

[12]  Klaus Weinert,et al.  Analysis and Simulation of Cutting Technologies for Lightweight Frame Components , 2006 .

[13]  Seoung Hwan Lee,et al.  Precision Laser Deburring and Acoustic Emission Feedback , 2001 .

[14]  Sangkee Min,et al.  FINITE ELEMENT MODELING OF BURR FORMATION IN METAL CUTTING , 2001 .

[15]  Du-Ming Tsai,et al.  Detecting and locating burrs of industrial parts , 1996 .

[16]  Chih-Hsing Chu,et al.  Tool Path Planning for Avoiding Exit Burrs , 2000 .

[17]  David Dornfeld,et al.  Probabilistic Precision Process Planning- P4 , 2003 .

[18]  Jinsoo Kim,et al.  Cost estimation of drilling operations by a Drilling Burr Control Chart and Bayesian statistics , 2001 .

[19]  David Dornfeld,et al.  Effect of In-Plane Exit Angle and Rake Angles on Burr Height and Thickness in Face Milling Operation , 1999 .

[20]  David Dornfeld,et al.  Finite element analysis of drilling burr minimization with a backup material , 1998 .

[21]  Masahiro Anzai,et al.  Application for Deburring of Mechanical Parts Using Magnetic Abrasive Finishing , 1993 .

[22]  Kenji Toda,et al.  Automation of chamfering by an industrial robot; for the case of hole on free-curved surface , 2002 .

[23]  P. T. Blotter,et al.  The Formation and Properties of Machining Burrs , 1976 .

[24]  Álisson Rocha Machado,et al.  Application of factorial design for studying the burr behaviour during face milling of motor engine blocks , 2006 .

[25]  Manfred Schlatter.  Entgraten durch Hochdruckwasserstrahlen , 1986 .

[26]  Kazuo Nakayama,et al.  Burr Formation in Metal Cutting , 1987 .

[27]  Tsann-Rong Lin,et al.  Experimental study of burr formation and tool chipping in the face milling of stainless steel , 2000 .

[28]  T. I. El-Wardany,et al.  PHYSICS-BASED SIMULATION OF HIGH SPEED MACHINING , 2002 .

[29]  Kazuo Nakayama,et al.  Effects of Chip Splitting Nicks in Drilling , 1985 .

[30]  J. Bonney,et al.  Burr formation in face milling of cast iron with different milling cutter systems , 2003 .

[31]  I. Aoki,et al.  New deburring method of blanked products , 1983 .

[32]  Miguel C. Avila,et al.  On The Face Milling Burr Formation Mechanisms and Minimization Strategies at High Tool Engagement , 2004 .

[33]  Berend Denkena,et al.  Burr Formation in Microstructuring Processes , 2010 .

[34]  David Dornfeld,et al.  A Study of Burr Formation Processes Using the Finite Element Method: Part II—The Influences of Exit Angle, Rake Angle, and Backup Material on Burr Formation Processes , 2000 .

[35]  Gui Cheng Wang,et al.  Study on the Forming Mechanism of the Cutting-Direction Burr in Metal Cutting , 2003 .

[36]  David Dornfeld,et al.  Drilling Burr Formation in Titanium Alloy, Ti-6AI-4V , 1999 .

[37]  Gwo-Lianq Chern,et al.  Experimental observation and analysis of burr formation mechanisms in face milling of aluminum alloys , 2006 .

[38]  R Neugebauer,et al.  Influence of Coating-Substrate Systems on Chip and Burr Formation in Precision Manufacturing , 2006 .

[39]  Chih-Hsing Chu,et al.  Geometric Approaches for Reducing Burr Formation in Planar Milling by Avoiding Tool Exits , 2008 .

[40]  Haizhuang Kang,et al.  Development of a hand-held Burr measurement system for statistical process control of the trimming process , 2000, Proceedings of the 17th IEEE Instrumentation and Measurement Technology Conference [Cat. No. 00CH37066].

[41]  Yuebin Guo,et al.  Finite Element Modeling of Burr Formation Process in Drilling 304 Stainless Steel , 2000 .

[42]  David Dornfeld,et al.  Analysis of Burr Formation Mechanism in Orthogonal Cutting , 1999 .

[43]  Sung-Lim Ko.  Development of Effective Measurement Method for Burr Geometry , 2003 .

[44]  Andrey A. Toropov.  An Effective Visualization and Analysis Method for Edge Measurement , 2007, ICCSA.

[45]  David Dornfeld,et al.  The Effect of Dry Machining on Burr Size , 2004 .

[46]  David Dornfeld,et al.  Burr Formation in Drilling Miniature Holes , 1997 .

[47]  Miomir Vukobratović,et al.  Contribution to the controller design in tasks of robot deburring , 1995 .

[48]  Ekkard Brinksmeier,et al.  Burr and Cap Formation by Orbital Drilling of Aluminum , 2010 .

[49]  Seoung Hwan Lee.  BURR SIZE MEASUREMENT USING A CAPACITANCE SENSOR , 1999 .

[50]  Athulan Vijayaraghavan,et al.  Quantifying Edge Defects in Drilled FRP Composites , 2006 .

[51]  Jan C. Aurich,et al.  Burr Formation and Surface Characteristics in Micro-End Milling of Titanium Alloys , 2010 .

[52]  Gwo-Lianq Chern,et al.  Study on boring and drilling with vibration cutting , 2007 .

[53]  Jan C. Aurich,et al.  Burr Formation in Drilling Intersecting Holes , 2010 .

[54]  Klaus Weinert,et al.  Schleifen von Formgedächtnislegierungen , 2002 .

[55]  David Dornfeld,et al.  Challenges in modeling machining in multilayer materials - eScholarship , 2005 .

[56]  L. K. Gillespie.  Deburring: an annotated bibliography , 1973 .

[57]  Jinsoo Kim,et al.  Development of a drilling burr control chart for low alloy steel, AISI 4118 , 2001 .

[58]  Akihiro Yamamoto,et al.  Study of Burr Formation in Face Milling (1st Report) , 1987 .

[59]  Shigeki Okuyama,et al.  Effect of plastic zone near workpiece ends on grinding burrs (Model for calculating the stress distribution near work end and results) , 1989 .

[60]  Uwe Heisel,et al.  Burr formation in intersecting holes , 2008, Prod. Eng..

[61]  David Dornfeld,et al.  Deburring of Cross-Drilled Hole Intersections by Mechanized Cutting , 2004 .

[62]  David Dornfeld,et al.  Drilling and deburring in a single process , 2003 .

[63]  Jan C. Aurich,et al.  Characterisation of Burr Formation in Grinding and Prospects for Modelling , 2005 .

[64]  Sheng Liu,et al.  Programming deburring robots based on human demonstration with direct burr size measurement , 1994, Proceedings of the 1994 IEEE International Conference on Robotics and Automation.

[65]  Seoung Hwan Lee,et al.  Precision Laser Deburring , 2001 .

[66]  Chih-Hsing Chu,et al.  Prediction and Simulation of Milling Burr Formation for Edge-Precision Process Planning , 2002 .

[67]  Han-Pang Huang,et al.  Burr detection by using vision image , 1993 .

[68]  O. Olvera,et al.  An experimental study of burr formation in square shoulder face milling , 1996 .

[69]  Dirk Biermann,et al.  Burr Minimization Strategies in Machining Operations , 2010 .

[70]  Sung-Lim Ko,et al.  Micro Deburring Technology Using Ultrasonic Vibration with Abrasive - eScholarship , 2004 .

[71]  Sangkee Min,et al.  Optimization and control of drilling burr formation of AISI 304L and AISI 4118 based on drilling burr control charts , 2001 .

[72]  David Dornfeld,et al.  Influences on Burr Size During Face-Milling of Aluminum Alloys and Cast Iron , 2004 .

[73]  Gui Cheng Wang,et al.  Mechanism of Burr Formation in Milling , 2003 .

[74]  Hans Haller.  Wer Entgraten sagt, sollte auch Wasser sagen! , 2004 .

[75]  David Dornfeld,et al.  Influence of Exit Surface Angle on Drilling Burr Formation , 2003 .

[76]  Andrey Toropov,et al.  A model of burr formation in the feed direction in turning , 2006 .

[77]  J. Leopold,et al.  Modeling and Simulation of Burr Formation: State-of-the-Art and Future Trends , 2010 .

[78]  T. Asokan,et al.  Control of interaction impedance using an electrohydraulic servosystem: an application to robotic deburring , 1997 .

[79]  David Dornfeld,et al.  A Study of Burr Formation Processes Using the Finite Element Method: Part I , 2000 .

[80]  David Dornfeld,et al.  Development of an Analytical Model for Drilling Burr Formation in Ductile Materials , 2002 .

[81]  Y. Kato,et al.  The Standardization for the Edge Quality of the Precise Machining Products , 2007 .

[82]  David Dornfeld,et al.  A study on Burr formation mechanism , 1991 .

[83]  Jan C. Aurich,et al.  Burr Measurement: A Round Robin Test Comparing Different Methods , 2010 .

[84]  David Dornfeld,et al.  Burr Minimization in Face Milling: A Geometric Approach , 1997 .

[85]  Sung-Lim Ko,et al.  Burr formation and fracture in oblique cutting , 1996 .

[86]  David Dornfeld,et al.  Micro-Burr Formation and Minimization through Process Control , 2003 .

[87]  Uwe Heisel,et al.  Burr formation in short hole drilling with minimum quantity lubrication , 2009, Prod. Eng..