Testing of the torsional stiffness of the passenger car frame and its validation by means of finite element analysis

The paper presents the results of the conducted tests of torsional stiffness of the VOSCO S106 passenger car, as well as the validation process of these tests by means of numerical analyses using the FEM finite element method. The most important element of the vehicle structure is the part of the spatial frame or the safety cage. Engine, brake system, fuel system and steering system, suspension as well as body and parts, their mounting nodes, hinges, locks, etc. are attached to the frame. The frame must therefore have adequate strength to protect the driver in the event of a tipover or impact. The frame is usually made of steel pipes with the prescribed dimensions and strength according to regulations. The torsional stiffness of the vehicle chassis has a significant influence on its driveability and therefore is an important parameter to measure. In this article, the torsional stiffness of the vehicle frame is calculated experimentally, which was then verified by finite element analysis (FEM) using the Altair HyperWorks program.

[1]  Ulrich Seiffert,et al.  Handbook of automotive engineering , 2005 .

[2]  Albert R. George,et al.  Design, Analysis and Testing of a Formula SAE Car Chassis , 2002 .

[3]  Ahmet E. Aktan,et al.  Damage Detection and Condition Assessment of Seymour Bridge , 1998 .

[4]  David Griffiths,et al.  A Technique for Relating Vehicle Structural Modes to Stiffness as Determined in Static Determinate Tests , 2003 .

[5]  R. C. Hibbeler.  Mechanics of Materials -7/E , 2014 .

[6]  A. Anand.  Torsional analysis of the chassis and its validation through Finite Element Analysis , 2017 .

[7]  Jason C. Brown,et al.  Motor Vehicle Structures: Concepts and Fundamentals , 2001 .

[8]  Zbigniew Kacprzyk,et al.  Metoda Elementów Skończonych w mechanice konstrukcji , 2016 .

[9]  Steven Tebby.  Methods to Determine Torsion Stiffness in an Automotive Chassis , 2011 .

[10]  Karen Margaret Holford,et al.  Measuring the Torsional Stiffness of a Space Frame Chassis Using 3D Motion Capture Techniques , 2005 .

[11]  Jerzy Czmochowski,et al.  Numerical and experimental analysis of a mine's loader boom crack , 2008 .

[12]  E. Harry Law,et al.  The Effects of Chassis Flexibility on Roll Stiffness of a Winston Cup Race Car , 1998 .

[13]  Francky Demeester.  Experimental compliance breakdown and real-time optical deformation measruement of flexible manipulatiors , 1992 .

[14]  Annalisa Fregolent,et al.  IDENTIFICATION OF RIGID BODY INERTIA PROPERTIES FROM EXPERIMENTAL DATA , 1996 .

[15]  E. Harry Law,et al.  Design of a Twist Fixture to Measure the Torsional Stiffness of a Winston Cup Chassis , 1998 .

[16]  Nancy L. Johnson,et al.  Development of a Cost Competitive, Composite Intensive, Body-in-White , 2002 .

[17]  Paul Sas,et al.  Modal Analysis Theory and Testing , 2005 .

[18]  Den Hartog.  Advanced Strength of Materials , 1952 .

[19]  Paul Sas,et al.  Global static and dynamic car body stiffness based on a single experimental modal analysis test , 2010 .

[20]  Krzysztof Podkowski,et al.  FEM (Finite Element Method) Numeric Analyses of the Syrenka S201 Car Model , 2016 .

[21]  Luc Cremers,et al.  Extraction of Static Car Body Stiffness from Dynamic Measurements , 2010 .

[22]  O. C. Zienkiewicz,et al.  The finite element method, fourth edition; volume 2: solid and fluid mechanics, dynamics and non-linearity , 1991 .

[23]  Paul Sas,et al.  Evaluation of the FRF based substructuring and modal synthesis technique applied to vehicle FE data , 2000 .

[24]  E. Harry Law,et al.  Design of a Winston Cup Chassis for Torsional Stiffness , 1998 .

[25]  Peter Mas,et al.  Estimation and use of residual modes in modal coupling calculations : A case study , 2000 .

[26]  M. Lenett,et al.  Modal Analysis of Multi-reference Impact Test Data for Steel Stringer Bridges , 1997 .

[27]  Aldo Sorniotti,et al.  Chassis Torsional Stiffness: Analysis of the Influence on Vehicle Dynamics , 2010 .

[28]  E. Rusiński,et al.  Tests of thin-walled beams joined by spot welding , 2004 .

[29]  B. Rediers,et al.  Static and Dynamic Stiffness: One Test, Both Results , 1998 .