Gear finishing by abrasive processes

Abstract Based on the position of hard finishing in the process chain of gear manufacturing, the dominant processes with a geometrically non-defined cutting edge are analysed. While processes like continuous profile grinding and discontinuous generating grinding with double cone discs became less important in the last couple of years, the processes continuous generating gear grinding, discontinuous profile grinding and honing of tooth flanks gain rising importance. The analyses of the processes include functionality, the development status, respectively, maturity as well as identifiable trends. Process superior aspects like dressing of the grinding wheel and honing rings and the problem of grinding burn will be considered and evaluated separately.

[1]  W. Liu.  Einfluss verschiedener Fertigungsverfahren auf die Graufleckentragfähigkeit von Zahnradgetrieben , 2003 .

[2]  Eckart Uhlmann,et al.  Development of a technology orientated programming system for industrial robots , 2008, Prod. Eng..

[3]  Hans Richter.  Barkhausenrauschanalyse: Erfahrungen im Laboreinsatz , 2002 .

[4]  Berend Denkena,et al.  Hard Fine Machining of Gears through Continuous Generating Grinding , 2004 .

[5]  Jian Lu,et al.  Handbook on Residual Stress , 2005 .

[6]  Bogdan Kruszyński,et al.  Forces in Generating Gear Grinding-Theoretical and Experimental Approach , 1998 .

[7]  Peter Langenstein.  Verbesserung der Bearbeitungsqualität beim Zahnradhonen durch Optimierung der Hauptspindelantriebsdynamik , 2005 .

[8]  A. M. Hoogstrate,et al.  J. J. Saurwalt: A method for synchronizing grinding wheel and form roll speed in point crush profiling of grinding wheels, Advances in abrasive technology X, Proceedings of ISAAT 2007 conference, Dearborn, USA , 2008 .

[9]  Bernhard Schmitz,et al.  Review of non-destructive measuring methods for the assessment of surface integrity : a survey of new measuring methods for coatings, layered structures and processed surfaces , 1999 .

[10]  B. Karpuschewski,et al.  Zahnflankenschleifen bogenverzahnter Kegelradsätze mit CBN-Schleifscheiben , 1997 .

[11]  J. Volkmuth,et al.  Einfluss ungleichmäßiger Eigenspannungen in Wälzlagerringen vor dem Härten auf Formabweichungen nach dem Härten∗ , 2005 .

[12]  Hans Kurt Tönshoff,et al.  Process Monitoring in Grinding Using Micromagnetic Techniques , 1999 .

[13]  Stephen P. Radzevich.  Computation of Parameters of a Form Grinding Wheel for Grinding of Shaving Cutter for Plunge Shaving of Topologically Modified Involute Pinion , 2005 .

[14]  E. Brinksmeler,et al.  Chip Formation Mechanisms in Grinding at Low Speeds , 2003 .

[15]  Hans Kurt Tönshoff,et al.  Sensors in manufacturing , 2002 .

[16]  Satoru Ezoe,et al.  Minimization of effect of CBN wheel wear on ground gear errors , 1999 .

[17]  Ekkard Brinksmeier,et al.  Grinding at very Low Speeds , 1997 .

[18]  S. Malkin,et al.  Thermal Analysis of Grinding , 2007 .

[19]  I. Inasaki,et al.  Grinding Chatter – Origin and Suppression , 2001 .

[20]  Piotr Kula,et al.  Synergistic effects of thermo-chemical treatment and super abrasive grinding in gears’ manufacturing , 2005 .

[21]  F. Rehsteiner,et al.  High Efficiency Abrasive Tool for Honing , 2002 .

[22]  A. M. Hoogstrate,et al.  Form crush dressing of diamond grinding wheels , 2008 .

[23]  Zongde Fang,et al.  Study on ultrasonic-assisted lapping of gears , 2007 .

[24]  H. J. Stadtfeld.  LEISTUNGSSPRUNG BEIM LAPPEN VON KEGEL- UND HYPOIDZAHNRADERN , 1999 .

[25]  T. Lierse,et al.  Dressing of grinding wheels for gearwheels , 2002 .

[26]  Ekkard Brinksmeier,et al.  Development and Application of a Wheel Based Process Monitoring System in Grinding , 2005 .

[27]  Wilfried Saxler.  Erkennung von Schleifbrand durch Schallemissionsanalyse , 1997 .

[28]  Ichiro Inasaki,et al.  Grinding Process Achievements and their Consequences on Machine Tools Challenges and Opportunities , 1998 .

[29]  K. Irie,et al.  Water-accelerated chemical reaction for producing gear teeth with high form accuracy and fine surface finish , 2005 .

[30]  H. K. Tönshoff,et al.  Tooth profile grinding of precision forged gears , 1999 .

[31]  Berend Denkena,et al.  Dressing of Vitreous Bonded Wheels for Continuous Generating Grinding of Gears , 2005 .

[32]  徐健,et al.  OKT , 1993 .

[33]  Jinsong Wang,et al.  Design and application of CBN shape grinding wheel for gears , 2003 .

[34]  Ekkard Brinksmeier,et al.  Advances in Modeling and Simulation of Grinding Processes , 2006 .

[35]  Berend Denkena,et al.  Characterization of Vitreous Bonded Grinding Wheels for CNC Crushing , 2004 .

[36]  M. Reichstein,et al.  Grinding of Gears with Vitreous Bonded CBN-Worms , 2006 .

[37]  Alexander Giwerzew,et al.  Spanbildungsmechanismen und tribologisches Prozeßverhalten beim Schleifen mit niedrigen Schnittgeschwindigkeiten , 2003 .

[38]  H.‐W. Zoch,et al.  From Single Production Step to Entire Process Chain – the Global Approach of Distortion Engineering , 2006 .

[39]  Ekkard Brinksmeier,et al.  Hard gear finishing viewed as a process of abrasive wear , 2005 .

[40]  G. Sulzer.  Combined cBN generating grinding and form grinding , 2003 .

[41]  C. Marzenell.  VERZAHNUNGSHONEN ERSETZT PROFILSCHLEIFEN , 1999 .