A Modular Fuel Cell, Modular DC–DC Converter Concept for High Performance and Enhanced Reliability

Fuel cell stacks produce a DC output with a 2:1 variation in output voltage from no-load to full-load. The output voltage of each fuel cell is about 0.4 V at full-load, and several of them are connected in series to construct a stack. An example 100 V fuel cell stack consists of 250 cells in series and to produce 300 V at full-load requires 750 cells stacked in series. Since fuel cells actively convert the supplied fuel to electricity, each cell requires proper distribution of fuel, humidification, coupled with water/thermal management needs. With this added complexity, stacking more cells in series decreases the reliability of the system. For example, in the presence of bad or malperforming cell/cells in a stack, uneven heating coupled with variations in cell voltages may occur. Continuous operation under these conditions may not be possible or the overall stack output power is severely limited. In this paper, a modular fuel cell powered by a modular DC-DC converter is proposed. The proposed concept electrically divides the fuel cell stack into various sections, each powered by a DC-DC converter. The proposed modular fuel cell powered by modular DC-DC converter eliminates many of these disadvantages, resulting in a fault tolerant system. A design example is presented for a 150-W, three-section fuel cell stack and DC-DC converter topology. Experimental results obtained on a 150-W, three-section proton exchange membrane (PEM) fuel cell stack powered by a modular DC-DC converter are discussed.

[1]  Leon M. Tolbert,et al.  Multilevel converters as a utility interface for renewable energy systems , 2000, 2000 Power Engineering Society Summer Meeting (Cat. No.00CH37134).

[2]  R. M. Button.  An advanced photovoltaic array regulator module , 1996, IECEC 96. Proceedings of the 31st Intersociety Energy Conversion Engineering Conference.

[3]  Rong-Jong Wai,et al.  High-efficiency power conversion for low power fuel cell generation system , 2005, IEEE Transactions on Power Electronics.

[4]  L.M. Tolbert,et al.  Optimum fuel cell utilization with multilevel DC-DC converters , 2004, Nineteenth Annual IEEE Applied Power Electronics Conference and Exposition, 2004. APEC '04..

[5]  J.R. McDonald,et al.  Grid connected inverter suitable for economic residential fuel cell operation , 2005, 2005 European Conference on Power Electronics and Applications.

[6]  Thierry Meynard,et al.  Switching faults and safe control of an ARCP multicell flying capacitor inverter , 2003 .

[7]  S. Rael,et al.  Mathematical model and characterization of the transient behavior of a PEM fuel cell , 2004, IEEE Transactions on Power Electronics.

[8]  Pierre R. Roberge,et al.  A practical PEM fuel cell model for simulating vehicle power sources , 1995, Proceedings of the Tenth Annual Battery Conference on Applications and Advances.

[9]  A. Khaligh,et al.  Power electronics intensive solutions for advanced electric, hybrid electric, and fuel cell vehicular power systems , 2006, IEEE Transactions on Power Electronics.

[10]  Thierry Meynard,et al.  Failures-tolerance and remedial strategies of a PWM multicell inverter , 2002 .

[11]  P. Enjeti,et al.  A new modular motor-modular inverter (MM-MI) concept for medium voltage adjustable speed drive systems , 1999, Conference Record of the 1999 IEEE Industry Applications Conference. Thirty-Forth IAS Annual Meeting (Cat. No.99CH36370).

[12]  Thierry Meynard,et al.  Switching frequency imposition and ripple reduction in DTC drives by using a multilevel converter , 2002 .

[13]  A.M. Khambadkone,et al.  Analysis and Implementation of a High Efficiency, Interleaved Current-Fed Full Bridge Converter for Fuel Cell System , 2007, IEEE Transactions on Power Electronics.

[14]  M.G. Simoes,et al.  Three-Port Bidirectional Converter for Hybrid Fuel Cell Systems , 2007, IEEE Transactions on Power Electronics.

[15]  M. Marchesoni,et al.  New DC–DC Converter for Energy Storage System Interfacing in Fuel Cell Hybrid Electric Vehicles , 2007, IEEE Transactions on Power Electronics.

[16]  Douglas J. Nelson,et al.  Fuel cell systems: efficient, flexible energy conversion for the 21st century , 2001, Proc. IEEE.

[17]  T. Meynard,et al.  Interactions Between Fuel Cells and Power Converters: Influence of Current Harmonics on a Fuel Cell Stack , 2007, IEEE Transactions on Power Electronics.

[18]  Hongwei Gao,et al.  Low cost high efficiency DC-DC converter for fuel cell powered auxiliary power unit of a heavy vehicle , 2006, IEEE Transactions on Power Electronics.

[19]  R. Ayyanar,et al.  Active input-voltage and load-current sharing in input-series and output-parallel connected modular DC-DC converters using dynamic input-voltage reference scheme , 2004, IEEE Transactions on Power Electronics.

[20]  H. Chiu,et al.  A Bidirectional DC/DC Converter for Fuel Cell Electric Vehicle Driving System , 2005 .

[21]  P.N. Enjeti,et al.  Development of a low cost fuel cell inverter system with DSP control , 2004, IEEE Transactions on Power Electronics.

[22]  P.L. Chapman,et al.  Mass-Optimal Design Methodology for DC-DC Converters in Low-Power Portable Fuel Cell Applications , 2008, IEEE Transactions on Power Electronics.

[23]  Jih-Sheng Lai,et al.  Low Frequency Current Ripple Reduction Technique With Active Control in a Fuel Cell Power System With Inverter Load , 2007, IEEE Transactions on Power Electronics.