Optimization of Unilateral Molar Rotation Correction by a Trans-palatal Bar: A Three-dimensional Analysis using the Finite Element Method

Objective The main goal of this study was to optimize unilateral molar rotation correction by modifying a trans-palatal arch (TPA) design using the finite element method. Design Three-dimensional analysis of different TPA designs was carried out using the finite element method. Setting Department of Orthodontics, Tehran University of Medical Sciences, Iran. Material and methods For this investigation, 13 three-dimensional finite element models were produced for different TPA designs without pre-activation bends. Each model contained a palatal bar and two tubes. Optimizing unilateral molar rotations was achieved by five separate different paths: incorporating U-loop(s), ‘R’ loop(s) or helix/helices, a reverse action of the helix/helices and adding a straight wire to the design. The mesial part of the left side tube was displaced 0·1, 0·25, 0·5 and 1 mm, successively towards the midline, simulating palatal bar tab engagement in a mesio-palatal rotated maxillary left molar. The mesio-distal force, moment and energy produced in the normal side (right) molar were recorded for each of the models. Results Findings showed that in all designs, the associated mesializing force was lower than that seen in the traditional design and the moment showed an increasing pattern when compared with a simple palatal bar. Regarding energy levels, the same increasing pattern was observed in the designs between activations of 0·1 and 1·0 mm. Conclusion According to our optimized system, the TPA design with the highest energy and moment, but the lowest mesializing force associated with derotating a maxillary molar tooth was a parallel wire II design (i.e. adding a straight wire).

[1]  J. McNamara,et al.  Effect of the transpalatal arch during extraction treatment. , 2008, American journal of orthodontics and dentofacial orthopedics : official publication of the American Association of Orthodontists, its constituent societies, and the American Board of Orthodontics.

[2]  C. Stephens.  Bioengineering analysis of orthodontic mechanics , 1986 .

[3]  Stephen J. Wright,et al.  Numerical Optimization , 2018, Fundamental Statistical Inference.

[4]  Yukio Kojima,et al.  Effects of transpalatal arch on molar movement produced by mesial force: a finite element simulation. , 2008, American journal of orthodontics and dentofacial orthopedics : official publication of the American Association of Orthodontists, its constituent societies, and the American Board of Orthodontics.

[5]  Bodily labializing lateral incisors: 3D analysis using finite element method , 2013, Acta odontologica Scandinavica.

[6]  H P Bantleon,et al.  An improved transpalatal bar design. Part I. Comparison of moments and forces delivered by two bar designs for symmetrical molar derotation. , 2009, The Angle orthodontist.

[7]  B. Ingervall,et al.  The effect of a transpalatal arch for the correction of first molar rotation. , 1996, European journal of orthodontics.

[8]  H. Luder,et al.  Influence of arch shape on the transverse effects of transpalatal arches of the Goshgarian type during application of buccal root torque. , 1982, American journal of orthodontics.

[9]  B. Ingervall,et al.  Moments and forces delivered by transpalatal arches for symmetrical first molar rotation. , 1996, European journal of orthodontics.

[10]  Allahyar Geramy,et al.  Abfraction: 3D analysis by means of the finite element method. , 2003, Quintessence international.

[11]  J. Powers,et al.  Maxillary molar vertical control with the use of transpalatal arches. , 1994, American journal of orthodontics and dentofacial orthopedics : official publication of the American Association of Orthodontists, its constituent societies, and the American Board of Orthodontics.

[12]  Yuki Chiba,et al.  Tongue pressure on loop of transpalatal arch during deglutition. , 2003, American journal of orthodontics and dentofacial orthopedics : official publication of the American Association of Orthodontists, its constituent societies, and the American Board of Orthodontics.

[13]  Robert J. Nikolai,et al.  Bioengineering Analysis of Orthodontic Mechanics , 1985 .

[14]  Franz Günter Sander,et al.  Development and Biomechanical Investigation of a New Compound Palatal Arch , 2004, Journal of Orofacial Orthopedics / Fortschritte der Kieferorthopädie.

[15]  A Geramy,et al.  Alveolar bone resorption and the center of resistance modification (3-D analysis by means of the finite element method). , 2000, American journal of orthodontics and dentofacial orthopedics : official publication of the American Association of Orthodontists, its constituent societies, and the American Board of Orthodontics.

[16]  D H Kohn,et al.  Stress-related molar responses to the transpalatal arch: a finite element analysis. , 1997, American journal of orthodontics and dentofacial orthopedics : official publication of the American Association of Orthodontists, its constituent societies, and the American Board of Orthodontics.

[17]  A. Kupietzky,et al.  The transpalatal arch: an alternative to the Nance appliance for space maintenance. , 2007, Pediatric dentistry.

[18]  Differences between Two Transpalatal Arch Systems upon First-, Second-, and Third-Order Bending Activation , 2001, Journal of Orofacial Orthopedics / Fortschritte der Kieferorthopädie.

[19]  C. Muralidharan,et al.  Multi-criteria decision making approach and experimental design as chemometric tools to optimize HPLC separation of domperidone and pantoprazole. , 2007, Journal of pharmaceutical and biomedical analysis.

[20]  Allahyar Geramy,et al.  Optimization of unilateral overjet management: three-dimensional analysis by the finite element method. , 2009, The Angle orthodontist.

[21]  C J Burstone,et al.  Precision adjustment of the transpalatal lingual arch: computer arch form predetermination. , 1981, American Journal of Orthodontics.

[22]  B. Zachrisson,et al.  An improved transpalatal bar design. Part II. Clinical upper molar derotation--case report. , 2009, The Angle orthodontist.

[23]  R. W. Bench.  The quad helix appliance. , 1998, Seminars in orthodontics.