An investigation of a TiAlO based refractory slurry face coat system for the investment casting of Ti–Al alloys

Abstract The investment casting process offers great freedom of design with the economic advantage of near net shape production and has been widely used to process TiAl alloys. An investigation was undertaken to develop stable and cheap refractory slurry systems, suitable for use as a face coat in the investment casting of titanium aluminides. A TiO2–Al2O3 (TiAlO) based face coat slurry was investigated and compared with a traditional yttria based face coat slurry. After sintering, the chemical inertness of the manufactured shells in contact with molten TiAl alloys was tested by simulating the casting process using a flash re-melting test, in which sample shells were in contact with titanium aluminides at given temperatures for varying time durations and subsequently re-solidified. Compared with yttria, the TiAlO face coat had relatively lower chemical inertness against molten alloys, forming a thick hardened layer at the metal/shell interface with massive interaction products along grain boundaries. The reaction also changed the wetting behaviour of the TiAl on the TiAlO face coat with the contact angle decreasing as a function of interaction time.

[1]  F. Froes,et al.  Solidification behavior of Ti5Si3 whiskers in TiAl alloys , 2003 .

[2]  J. Barbosa,et al.  Induction melting of γ-TiAl in CaO crucibles , 2008 .

[3]  A. Caetano Monteiro,et al.  Influence of superheating on casting of γ-TiAl , 2007 .

[4]  R. Yang,et al.  Intensified interfacial reactions between gamma titanium aluminide and CaO stabilised ZrO2 , 2004 .

[5]  R. Misra,et al.  On the evaluation of stability of rare earth oxides as face coats for investment casting of titanium , 1990 .

[6]  D. Chatain,et al.  Wetting and interfacial chemistry in liquid metal-ceramic systems , 1991 .

[7]  D. Bandyopadhyay.  The Ti-Si-C system (Titanium-Silicon-Carbon) , 2004 .

[8]  N. Eustathopoulos.  Dynamics of wetting in reactive metal/ ceramic systems , 1998 .

[9]  J. Bonnentien,et al.  Effects of interstitial oxygen on microstructure and mechanical properties of Ti-48Al-2Cr-2Nb with fully lamellar and duplex microstructures , 2006 .

[10]  R. A. Harding,et al.  Microstructures and properties of investment castings of γ-titanium aluminide , 2002 .

[11]  D. Zivkovic,et al.  Predicting thermodynamic properties in Ti–Al binary system by FactSage , 2006 .

[12]  M. Golovkova,et al.  Phase equilibria in the α-Ti-Al-Si region of the Ti-Si-Al system , 2004 .

[13]  Jingjie Guo,et al.  Wettability of TiAl alloy melt on ceramic moulds in electromagnetic field , 2008 .

[14]  H. Flower,et al.  Microstructure and phase relationships in Ti–Al–Si system , 1999 .

[15]  K. Prabhu,et al.  Review of non-reactive and reactive wetting of liquids on surfaces. , 2007, Advances in colloid and interface science.

[16]  J. Zollinger,et al.  Influence of oxygen on solidification behaviour of cast TiAl-based alloys , 2007 .

[17]  A. Kostov,et al.  Predicting thermodynamic stability of crucible oxides in molten titanium and titanium alloys , 2006 .

[18]  Qudong Wang,et al.  High strength extruded Mg–5Zn–2Nd–1.5Y–0.6Zr–0.4Ca alloy produced by electromagnetic casting , 2005 .

[19]  J. D. Hosson,et al.  Reactive wetting of liquid metals on ceramic substrates , 1996 .

[20]  Xinhua Wu.  Review of alloy and process development of TiAl alloys , 2006 .

[21]  R. Misra,et al.  Evaluation of the reactivity of titanium with mould materials during casting , 1989 .

[22]  Gao Ming,et al.  Interactions between TiAl alloys and yttria refractory material in casting process , 2010 .