In-plane laser forming for high precision alignment

Abstract. Laser microforming is extensively used to align components with submicrometer accuracy, often after assembly. While laser-bending sheet metal is the most common laser-forming mechanism, the in-plane upsetting mechanism is preferred when a high actuator stiffness is required. A three-bridge planar actuator made out of Invar 36 sheet was used to characterize this mechanism by experiments, finite element method modeling, and a fast-reduced model. The predictions of the thermal models agree well with the temperature measurements, while the final simulated displacement after 15 pulses deviates up to a factor of 2 from the measurement, using standard isotropic hardening models. Furthermore, it was found from the experiments and models that a small bridge width and a large bridge thickness are beneficial to decrease the sensitivity to disturbances in the process. The experiments have shown a step size as small as 0.1  μm, but with a spread of 20%. This spread is attributed to scattering in surface morphology, which affects the absorbed laser power. To decrease the spread and increase the positioning accuracy, an adapted closed-loop learning algorithm is proposed. Simulations using the reduced model showed that 78% of the alignment trials were within the required accuracy of ±0.1  μm.

[1]  Th.B. Kermanidis,et al.  An analytical model for the prediction of distortions caused by the laser forming process , 2000 .

[2]  T. Kermanidis,et al.  Numerical and experimental investigation of the laser forming process , 1999 .

[3]  X. Richard Zhang,et al.  Microscale bending using pulsed and cw laser , 2001, SPIE LASE.

[4]  Hong Shen,et al.  Numerical and experimental investigation of cooling time in laser micro-adjustment of two-bridge actuators , 2011 .

[5]  Hong Shen,et al.  Study on the mechanical behavior of laser micro-adjustment of two-bridge actuators , 2010 .

[6]  Gerd Esser,et al.  Laser-based microalignment for fabrication of highly precise 2D fiber collimator arrays , 2004, SPIE LASE.

[7]  Alexander Olowinsky,et al.  Laser beam micro forming as a new adjustment technology using dedicated actuator structures , 2003, SPIE Microtechnologies.

[8]  Gareth Thomson,et al.  Improvements to laser forming through process control refinements , 1998 .

[9]  Y. Lawrence Yao,et al.  Laser Bending of Tubes: Mechanism, Analysis, and Prediction , 2001 .

[10]  F. Vollertsen,et al.  The laser bending of steel foils for microparts by the buckling mechanism-a model , 1995 .

[11]  Lin Li,et al.  The Effect of Nonconventional Laser Beam Geometries on Stress Distribution and Distortions in Laser Bending of Tubes , 2007 .

[12]  Lin Li,et al.  An analytical model for laser tube bending , 2003 .

[13]  T. Hung,et al.  Laser Hammering Technique in Butterfly Laser Diode Module , 2007, 2007 9th Electronics Packaging Technology Conference.

[14]  Willem Hoving,et al.  Accurate manipulation using laser technology , 1997, Other Conferences.

[15]  Lin Li,et al.  Finite element simulation of laser tube bending: Effect of scanning schemes on bending angle, distortions and stress distribution , 2007 .

[16]  Matthias Rank,et al.  Laser micro adjustment—from new basic process knowledge to the application , 2007 .

[17]  Hong Shen.  Mechanism of laser micro-adjustment , 2008 .

[18]  F. Vollertsen,et al.  On the working accuracy of laser bending , 1997 .

[19]  F. Vollertsen,et al.  Modelling of laser forming – An review , 2009 .

[20]  Xianfan Xu.  Laser-based microscale bending for microelectronics fabrication , 2000, LASE.

[21]  Lin Li,et al.  Finite element analysis of laser tube bending process , 2003 .

[22]  Michael Schmidt,et al.  Laser adjustable actuators for high-accuracy positioning of micro components , 2003, International Symposium on Laser Precision Microfabrication.

[23]  A. J. Huis in 't Veld,et al.  High precision laser forming for microactuation , 2014, Photonics West - Lasers and Applications in Science and Engineering.

[24]  Andrew G. Glen,et al.  APPL , 2001 .