Optimization of the non-axisymmetric stator casing of a 1.5 stage axial turbine

Abstract The interaction of secondary flows with the main passage flow in turbomachines results in entropy generation and in aerodynamic loss. This loss source is most relevant to low aspect ratio blades. One approach for reducing this flow energy loss is by endwall contouring. However, limited work has been reported on using non-axisymmetric endwalls at the stator casing and on its interaction with the tip leakage flow. In this paper, a non-axisymmetric endwall design method for the stator casing is implemented through a novel surface definition, towards mitigating secondary flow losses. This design is tested on a three-dimensional axial turbine RANS model built in OpenFOAM 3.2 Extend, with k−ω SST turbulence closure. The flow analysis confirms the foundations of the new surface definition approach, which is implemented using Alstom Process and Optimization Workbench (APOW) software. Computer-based optimization of the surface topology is demonstrated towards automating the design process of axial turbines in an industrial design workflow. The design is optimized using the total pressure loss across the first stator and across the full stage, as the target function. Numerical predictions of the 1.5 stage axial turbine show the positive impact of the optimized casing design on the efficiency that increases by 0.69% against the benchmark axisymmetric stage from RWTH Aachen, which is validated against experiment. The new non-axisymmetric casing is also beneficial at off-design condition. The effective mitigation of the secondary flows is predicted to give a 0.73% efficiency gain off-design.

[1]  Martin G. Rose,et al.  Improving the Efficiency of the Trent 500-HP Turbine Using Nonaxisymmetric End Walls—Part I: Turbine Design , 2003 .

[2]  Vincenzo Dossena,et al.  The Influence of Endwall Contouring on the Performance of a Turbine Nozzle Guide Vane , 1998 .

[3]  Florian Menter,et al.  The SST Turbulence Model with Improved Wall Treatment for Heat Transfer Predictions in Gas Turbines , 2003 .

[4]  C. H. Sieverding,et al.  Recent Progress in the Understanding of Basic Aspects of Secondary Flows in Turbine Blade Passages , 1985 .

[5]  Giacomo Bruno Azzurro Persico,et al.  Evolutionary Optimization of Centrifugal Nozzles for Organic Vapours , 2017 .

[6]  Ayad Al Jubori,et al.  Performance enhancement of a small-scale organic Rankine cycle radial-inflow turbine through multi-objective optimization algorithm , 2017 .

[7]  Franz Joos,et al.  Experimental and Numerical Investigations of Flowpath Profiling on Secondary Flow Losses in a Turbine Control Stage , 2013 .

[8]  Guillermo Paniagua,et al.  Design and analysis of pioneering high supersonic axial turbines , 2014 .

[9]  Aldo Rona,et al.  Numerical Study of the Flow Past an Axial Turbine Stator Casing and Perspectives for its Management , 2017 .

[10]  Martin G. Rose,et al.  Improving Turbine Efficiency Using Non-Axisymmetric End Walls: Validation in the Multi-Row Environment and With Low Aspect Ratio Blading , 2002 .

[11]  Andrea Lazzaretto,et al.  Predicting the optimum design of single stage axial expanders in ORC systems: Is there a single efficiency map for different working fluids? , 2016 .

[12]  Huimin Tang,et al.  Design Optimization of Profiled Endwall in a High Work Turbine , 2014 .

[13]  L. Langston,et al.  Secondary Flows in Axial Turbines—A Review , 2001, Annals of the New York Academy of Sciences.

[14]  Martin G. Rose.  NON-AXISYMMETRIC ENDWALL PROFILING IN THE HP NGV's OF AN AXIAL FLOW GAS TURBINE , 1994 .

[15]  Xiaojing Sun,et al.  Preliminary design and performance analysis of a centrifugal turbine for Organic Rankine Cycle (ORC) applications , 2017 .

[16]  John D. Denton,et al.  The 1993 IGTI Scholar Lecture: Loss Mechanisms in Turbomachines , 1993 .

[17]  Farzad Taremi.  Endwall Flows in Transonic Turbine Cascades , 2013 .

[18]  J. H. Horlock,et al.  Review: Secondary flows and losses in cascades and axial-flow turbomachines , 1963 .

[19]  Jay L. Devore,et al.  Probability and statistics for engineering and the sciences , 1982 .

[20]  T. J. Praisner,et al.  Application of Nonaxisymmetric Endwall Contouring to Conventional and High-Lift Turbine Airfoils , 2013 .

[21]  Richard J Goldstein,et al.  Flow visualization in a linear turbine cascade of high performance turbine blades , 1995 .

[22]  P. Roache.  Perspective: A Method for Uniform Reporting of Grid Refinement Studies , 1994 .

[23]  David Gregory-Smith,et al.  Non-Axisymmetric Turbine End Wall Design: Part II — Experimental Validation , 1999 .

[24]  Eberhard Nicke,et al.  AUTOMATED OPTIMIZATION OF THE NON-AXISYMMETRIC HUB ENDWALL OF THE ROTOR OF AN AXIAL COMPRESSOR , 2013 .

[25]  Ayad Al Jubori,et al.  Development of micro-scale axial and radial turbines for low-temperature heat source driven organic Rankine cycle , 2016 .

[26]  David Gregory-Smith,et al.  Nonaxisymmetric Turbine End Wall Design: Part I— Three-Dimensional Linear Design System , 2000 .

[27]  Les A. Piegl,et al.  The NURBS Book , 1995, Monographs in Visual Communication.

[28]  Grant Ingram,et al.  The Effect of End-Wall Profiling on Secondary Flow and Loss Development in a Turbine Cascade , 2002 .

[29]  D. Wilcox.  Turbulence modeling for CFD , 1993 .

[30]  Giacomo Bruno Azzurro Persico,et al.  Optimization of organic Rankine cycle power systems considering multistage axial turbine design , 2018 .

[31]  Reza S. Abhari,et al.  Improving Efficiency of a High Work Turbine Using Nonaxisymmetric Endwalls— Part I: Endwall Design and Performance , 2010 .

[32]  Reza S. Abhari,et al.  Improving Efficiency of a High Work Turbine Using Nonaxisymmetric Endwalls—Part II: Time-Resolved Flow Physics , 2010 .

[33]  Mukka Govardhan,et al.  Secondary Flow Loss Reduction in a Turbine Cascade with a Linearly Varied Height Streamwise Endwall Fence , 2011 .

[34]  Zhenping Feng,et al.  Non-Axisymmetric Turbine Endwall Aerodynamic Optimization Design: Part I — Turbine Cascade Design and Experimental Validations , 2014 .