Molecular conformation and disjoining pressure of polymeric liquid films

Atomic force microscopy, angle resolved x‐ray photoelectron spectroscopy, and ellipsometry are applied to study the conformation of fluorocarbon polymers in molecularly thin liquid films, 5–130 A thick, on solid surfaces. The combination of these techniques shows that the physisorbed polymers at the solid surface have an extended, flat conformation. In addition, the disjoining pressure of these liquid films is determined from atomic force microscopy measurements of the distance needed to break the liquid meniscus that forms between solid surface and force microscope tip. For a monolayer thickness of ∼7 A, the disjoining pressure is ∼5 MPa, indicating strong attractive interaction between the polymer molecules and the solid surface. The disjoining pressure decreases with increasing film thickness in a manner consistent with a strong attractive van der Waals interaction between the liquid molecules and the solid surface.

[1]  V. Novotny.  Migration of liquid polymers on solid surfaces , 1990 .

[2]  D. Theodorou.  Structure and thermodynamics of bulk homopolymer/solid interfaces: a site lattice model approach , 1988 .

[3]  G. J. Fleer,et al.  Statistical theory of the adsorption of interacting chain molecules. II. Train, loop, and tail size distribution , 1980 .

[4]  W. A. Dench,et al.  Quantitative electron spectroscopy of surfaces: A standard data base for electron inelastic mean free paths in solids , 1979 .

[5]  Georges Hadziioannou,et al.  Molecular dynamics simulations of the structure and dynamics of confined polymer melts , 1990 .

[6]  J. E. Stern,et al.  Force microscope using a fiber‐optic displacement sensor , 1988 .

[7]  Jacob N. Israelachvili,et al.  Intermolecular and surface forces : with applications to colloidal and biological systems , 1985 .

[8]  T. King,et al.  Neutron scattering, nuclear magnetic resonance and photon correlation studies of polymers adsorbed at the solid-solution interface , 1981 .

[9]  P. Mee,et al.  ESCA determination of fluorocarbon lubricant film thickness on magnetic disk media , 1982 .

[10]  C. Mate,et al.  Overcoats and Lubrication for Thin Film Disks , 1990 .

[11]  D. Y. Yoon,et al.  Off‐lattice Monte Carlo simulations of polymer melts confined between two plates , 1988 .

[12]  C. Mathew Mate,et al.  Atomic force microscopy of polymeric liquid films , 1989 .

[13]  Blackman,et al.  Interaction forces of a sharp tungsten tip with molecular films on silicon surfaces. , 1990, Physical review letters.

[14]  K. L. Smith,et al.  Using angle resolved ESCA to characterize Winchester disks , 1986 .

[15]  D. Sianesi,et al.  Perfluoropolyethers: Their physical properties and behaviour at high and low temperatures , 1971 .

[16]  Michael F. Toney,et al.  X‐ray reflectivity on perfluoropolyether polymer molecules on amorphous carbon , 1990 .

[17]  D. Rugar,et al.  Improved fiber‐optic interferometer for atomic force microscopy , 1989 .

[18]  Michael R. Philpott,et al.  Liquid polymer conformation on solid surfaces , 1989 .

[19]  B. Derjaguin,et al.  Structural component of disjoining pressure , 1974 .

[20]  W. G. Madden,et al.  Monte Carlo studies of the melt–vacuum interface of a lattice polymer , 1987 .

[21]  Akira Terada,et al.  Uniformity quantification of lubricant layer on magnetic recording media , 1987 .

[22]  M. Lorenz,et al.  Determination of lubricant film thickness on a particulate disk surface by atomic force microscopy , 1990 .

[23]  F. T. Wall,et al.  Self‐avoiding walks subject to boundary constraints , 1977 .