Recent Advancement for Green and Sustainable Manufacturing Grinding Process: A Review

Article history: Received 04 November 2019 Accepted 18 November 2019 Available online 16 December 2019 Lubrication is prime requirement of metal cutting industries to assure high quality performance. A lot of heat developed because of high friction during an abrasive material removal process. The conventional method of cooling consumes high amount of coolant but still insufficient to control thermal related problems. The proper penetration of coolant is not possible and most of the fluid goes in waste form. This method is uneconomical and eco-friendly less. The alternative is minimum quantity lubrication technique, in which a minute amount of lubricant with high air velocity delivers directly to cutting zone for effective penetration. The nanofluids have excellent convection heat transfer and thermal conductivity properties. To reduce the excess usage of grinding fluid, nanofluid has recently applied to grinding process using minimum quantity lubrication technique. The MQL based nanofluid technique (nanofluid MQL) gives better cooling and lubricating effects which improves overall grinding performance compared to conventional flooded, MQL and pure nanofluid machining. This literature study provides a review on results obtained for grinding process in different grinding environments. It helps to find the research gap for the researchers to develop green and sustainable grinding process for better results.

[1]  T. D. Lavanya,et al.  Design of an eco-friendly coolant for grinding using anti-bacterial additive , 2010 .

[2]  Dongzhou Jia,et al.  Experimental Evaluation of the Lubrication Performance of MoS2/CNT Nanofluid for Minimal Quantity Lubrication in Ni-based Alloy Grinding , 2015 .

[3]  K. M. Kumar,et al.  Analysis of Nanofluids as Cutting Fluid in Grinding EN-31 Steel , 2011 .

[4]  Tsuyoshi Murata,et al.  {m , 1934, ACML.

[5]  Mohammadjafar Hadad,et al.  Performance improvement of eco-friendly MQL technique by using hybrid nanofluid and ultrasonic-assisted grinding , 2017 .

[6]  Barbara Linke,et al.  Effect of Manual Grinding Operations on Surface Integrity , 2016 .

[7]  Fereydoun Aghazadeh,et al.  Health Risks From Exposure to Metal-Working Fluids in Machining and Grinding Operations , 2003, International journal of occupational safety and ergonomics : JOSE.

[8]  B. Shen,et al.  PERFORMANCE OF NOVEL MoS2 NANOPARTICLES BASED GRINDING FLUIDS IN MINIMUM QUANTITY LUBRICATION GRINDING , 2008 .

[9]  nbspSuresh P. Thakor,et al.  An Experimental Investigation on Cylindrical Grinding Process Parameters for En 8 Using Regression Analysis , 2014 .

[10]  Eduardo Carlos Bianchi,et al.  Analysis of the different forms of application and types of cutting fluid used in plunge cylindrical grinding using conventional and superabrasive CBN grinding wheels , 2006 .

[11]  Ibrahim Ciftci,et al.  An Investigation into the Influences of Grain Size and Grinding Parameters on Surface Roughness and Grinding Forces when Grinding , 2010 .

[12]  Zhixiong Zhou,et al.  The influence of spraying parameters on grinding performance for nanofluid minimum quantity lubrication , 2013 .

[13]  Dongzhou Jia,et al.  Specific grinding energy and surface roughness of nanoparticle jet minimum quantity lubrication in grinding , 2015 .

[14]  C. Sobhan,et al.  MOLECULAR DYNAMICS MODELING OF THERMAL CONDUCTIVITY ENHANCEMENT IN METAL NANOPARTICLE SUSPENSIONS , 2008 .

[15]  João Fernando Gomes de Oliveira,et al.  Development of new cutting fluid for grinding process adjusting mechanical performance and environmental impact , 2006 .

[16]  Huaqing Xie,et al.  Discussion on the thermal conductivity enhancement of nanofluids , 2011, Nanoscale research letters.

[17]  N. H. Woolley,et al.  Useful coolant flowrate in grinding , 2004 .

[18]  Manoj Kumar Sinha,et al.  Application of eco-friendly nanofluids during grinding of Inconel 718 through small quantity lubrication , 2017 .

[19]  Y. Yoon,et al.  Analysis of oxide (Al2O3, CuO, and ZnO) and CNT nanoparticles disaggregation effect on the thermal conductivity and the viscosity of nanofluids , 2014 .

[20]  A. Vinod,et al.  The Effective Thermal Conductivity of Water Based Nanofluids at Different Temperatures , 2016 .

[21]  K. Wasewar,et al.  Effect of sonication time on enhancement of effective thermal conductivity of nano TiO2–water, ethylene glycol, and paraffin oil nanofluids and models comparisons , 2015 .

[22]  Zhixiong Zhou,et al.  Analysis of suspension stability for nanofluid applied in minimum quantity lubricant grinding , 2014 .

[23]  B. K. Vinayagam,et al.  Nano surface generation of grinding process using carbon nano tubes , 2010 .

[24]  Taghi Tawakoli,et al.  Influence of oil mist parameters on minimum quantity lubrication – MQL grinding process , 2010 .

[25]  Eduardo Carlos Bianchi,et al.  Analysis of surface integrity for minimum quantity lubricant—MQL in grinding , 2007 .

[26]  B. K. Vinayagam,et al.  AFM investigation in grinding process with nanofluids using Taguchi analysis , 2012 .

[27]  Yang Li,et al.  Experimental investigation on the heat transfer properties of Al2O3 nanofluids using the mixture of ethylene glycol and water as base fluid , 2012 .

[28]  Amitava Ghosh,et al.  Grinding of Ti-6Al-4V Under Small Quantity Cooling Lubrication Environment Using Alumina and MWCNT Nanofluids , 2017 .

[29]  Taghi Tawakoli,et al.  Minimal quantity lubrication-MQL in grinding of Ti–6Al–4V titanium alloy , 2009 .

[30]  Mirko Soković,et al.  Ecological aspects of the cutting fluids and its influence on quantifiable parameters of the cutting processes , 2001 .

[31]  Zhixiong Zhou,et al.  Investigation of grinding characteristic using nanofluid minimum quantity lubrication , 2012 .

[32]  Sharad S. Chaudhari,et al.  Evaluation of the effects of machining parameters on MQL based surface grinding process using response surface methodology , 2017 .

[33]  Albert J. Shih,et al.  Application of Nanofluids in Minimum Quantity Lubrication Grinding , 2008 .

[34]  Robert Bauer,et al.  A review of cutting fluid application in the grinding process , 2005 .

[35]  Dae-Eun Kim,et al.  Nano-lubrication: A review , 2016 .

[36]  P. Venkateswara Rao,et al.  Application of Nano Cutting Fluid under Minimum Quantity Lubrication (MQL) Technique to Improve Grinding of Ti – 6Al – 4V Alloy , 2012 .

[37]  Barbara Linke,et al.  Sustainability of abrasive processes , 2013 .

[38]  Y. Shokoohi,et al.  Application of Nanofluids in Machining Processes - A Review , 2015 .

[39]  M. Sadeghi,et al.  An experimental investigation of the effects of workpiece and grinding parameters on minimum quantity lubrication—MQL grinding , 2009 .

[40]  M. Shabgard,et al.  Investigation into the performance of eco-friendly graphite nanofluid as lubricant in MQL grinding , 2019, Machining Science and Technology.

[41]  N. H. Woolley,et al.  The effects of cutting fluid application methods on the grinding process , 2000 .

[42]  Arun S. Mujumdar,et al.  A review on nanofluids - part II: experiments and applications , 2008 .

[43]  A. Rahimi,et al.  Performance improvement of minimum quantity lubrication (MQL) technique in surface grinding by modeling and optimization , 2015 .

[44]  K. Kadirgama,et al.  Performance of Water-Based Zinc Oxide Nanoparticle Coolant during Abrasive Grinding of Ductile Cast Iron , 2014 .

[45]  Naiqing Zhang,et al.  Experimental evaluation on tribological performance of the wheel/workpiece interface in minimum quantity lubrication grinding with different concentrations of Al2O3 nanofluids , 2017 .

[46]  Dongzhou Jia,et al.  Experimental research on the energy ratio coefficient and specific grinding energy in nanoparticle jet MQL grinding , 2015 .

[47]  Zhixiong Zhou,et al.  Experimental investigation of surface quality for minimum quantity oil–water lubrication grinding , 2012 .

[48]  Valan Arasu Amirtham,et al.  A review on preparation, characterization, properties and applications of nanofluids , 2016 .

[49]  Yulong Ding,et al.  Particle migration in a flow of nanoparticle suspensions , 2005 .

[50]  Mohammadjafar Hadad,et al.  An experimental investigation of the effects of machining parameters on environmentally friendly grinding process , 2015 .

[51]  Wenhua Yu,et al.  Review and Comparison of Nanofluid Thermal Conductivity and Heat Transfer Enhancements , 2008 .

[52]  C. Patil,et al.  Analysis of process parameters in surface grinding using single objective Taguchi and multi-objective grey relational grade , 2016 .

[53]  E. Brinksmeier,et al.  Friction, Cooling and Lubrication in Grinding , 1999 .

[54]  Mahmudur Rahman,et al.  Environmental impacts and hazards associated with metal working fluids and recent advances in the sustainable systems: A review , 2016 .

[55]  Danna Zhou,et al.  d. , 1934, Microbial pathogenesis.

[56]  Ling Yin,et al.  Analytical and experimental investigation of coolant velocity in high speed grinding , 2004 .

[57]  Amitava Ghosh,et al.  Synthesis of MWCNT nanofluid and evaluation of its potential besides soluble oil as micro cooling-lubrication medium in SQL grinding , 2015 .

[58]  Somchai Wongwises,et al.  Enhancement of heat transfer using nanofluids—An overview , 2010 .

[59]  Manoj Kumar Sinha,et al.  Performance evaluation of Ti–6Al–4V grinding using chip formation and coefficient of friction under the influence of nanofluids , 2015 .

[60]  Z. Deng,et al.  Investigation on grind-hardening annealed AISI5140 steel with minimal quantity lubrication , 2017 .

[61]  Yang Min,et al.  Experimental evaluation of the lubrication properties of the wheel/workpiece interface in MQL grinding with different nanofluids , 2016 .

[62]  Ajay P. Malshe,et al.  Bio-inspired surface engineering and tribology of MoS2 overcoated cBN–TiN composite coating , 2006 .

[63]  V. Radhakrishnan,et al.  Analysis of process parameters in surface grinding with graphite as lubricant based on the Taguchi method , 2003 .

[64]  Bijoy Mandal,et al.  Development of a Grinding Fluid Delivery Technique and Its Performance Evaluation , 2012 .

[65]  Thermal Conductivity and Viscosity of Vegetable Oil–Based Cu, Zn, and Cu–Zn Hybrid Nanofluids , 2016 .