The influence of cell morphology on the compressive fatigue behavior of Ti-6Al-4V meshes fabricated by electron beam melting.

Additive manufacturing technique is a promising approach for fabricating cellular bone substitutes such as trabecular and cortical bones because of the ability to adjust process parameters to fabricate different shapes and inner structures. Considering the long term safe application in human body, the metallic cellular implants are expected to exhibit superior fatigue property. The objective of the study was to study the influence of cell shape on the compressive fatigue behavior of Ti-6Al-4V mesh arrays fabricated by electron beam melting. The results indicated that the underlying fatigue mechanism for the three kinds of meshes (cubic, G7 and rhombic dodecahedron) is the interaction of cyclic ratcheting and fatigue crack growth on the struts, which is closely related to cumulative effect of buckling and bending deformation of the strut. By increasing the buckling deformation on the struts through cell shape design, the cyclic ratcheting rate of the meshes during cyclic deformation was decreased and accordingly, the compressive fatigue strength was increased. With increasing bending deformation of struts, fatigue crack growth in struts contributed more to the fatigue damage of meshes. Rough surface and pores contained in the struts significantly deteriorated the compressive fatigue strength of the struts. By optimizing the buckling and bending deformation through cell shape design, Ti-6Al-4V alloy cellular solids with high fatigue strength and low modulus can be fabricated by the EBM technique.

[1]  E. Maire,et al.  Experimental study of porosity and its relation to fatigue mechanisms of model Al–Si7–Mg0.3 cast Al alloys , 2001 .

[2]  T. McMahon,et al.  Creep contributes to the fatigue behavior of bovine trabecular bone. , 1998, Journal of biomechanical engineering.

[3]  L. Murr,et al.  Influence of cell shape on mechanical properties of Ti-6Al-4V meshes fabricated by electron beam melting method. , 2014, Acta biomaterialia.

[4]  C. M. Sonsino,et al.  Fatigue strength and applications of cast aluminium alloys with different degrees of porosity , 1993 .

[5]  Hamid Nayeb-Hashemi,et al.  Mechanical properties of open-cell rhombic dodecahedron cellular structures , 2012 .

[6]  S. Suresh.  Fatigue of materials , 1991 .

[7]  Amir A. Zadpoor,et al.  Computational prediction of the fatigue behavior of additively manufactured porous metallic biomaterials , 2016 .

[8]  M. Ashby,et al.  Cellular solids: Structure & properties , 1988 .

[9]  Ryan B. Wicker,et al.  Characterization of Ti–6Al–4V open cellular foams fabricated by additive manufacturing using electron beam melting , 2010 .

[10]  S. Stanzl-Tschegg,et al.  Influence of porosity on the fatigue limit of die cast magnesium and aluminium alloys , 2003 .

[11]  Y. Murakami,et al.  Effects of defects, inclusions and inhomogeneities on fatigue strength , 1994 .

[12]  Denis J Marcellin-Little,et al.  In vitro biocompatibility of titanium alloy discs made using direct metal fabrication. , 2010, Medical engineering & physics.

[13]  L. Fedrizzi,et al.  Characterization of cellular solids in Ti6Al4V for orthopaedic implant applications: Trabecular titanium. , 2010, Journal of the mechanical behavior of biomedical materials.

[14]  H Van Oosterwyck,et al.  The effect of pore geometry on the in vitro biological behavior of human periosteum-derived cells seeded on selective laser-melted Ti6Al4V bone scaffolds. , 2012, Acta biomaterialia.

[15]  A. A. Zadpoor,et al.  Mechanical properties of open-cell metallic biomaterials manufactured using additive manufacturing , 2013 .

[16]  L. Gibson,et al.  Analysis of crack growth in a 3D Voronoi structure: a model for fatigue in low density trabecular bone. , 2002, Journal of biomechanical engineering.

[17]  Di Wang,et al.  Mechanical properties of a Ti6Al4V porous structure produced by selective laser melting , 2013 .

[18]  A. A. Zadpoor,et al.  Fatigue behavior of porous biomaterials manufactured using selective laser melting. , 2013, Materials science & engineering. C, Materials for biological applications.

[19]  Carolin Körner,et al.  Compression-compression fatigue of selective electron beam melted cellular titanium (Ti-6Al-4V). , 2011, Journal of biomedical materials research. Part B, Applied biomaterials.

[20]  Yi Li,et al.  Functionally Graded Ti‐6Al‐4V Meshes with High Strength and Energy Absorption , 2016 .

[21]  Yang Hao,et al.  Compression fatigue behavior of Ti-6Al-4V mesh arrays fabricated by electron beam melting , 2012 .

[22]  Shivakumar Raman,et al.  Mechanical evaluation of porous titanium (Ti6Al4V) structures with electron beam melting (EBM). , 2010, Journal of the mechanical behavior of biomedical materials.

[23]  M. von Walter,et al.  Structural, mechanical and in vitro characterization of individually structured Ti-6Al-4V produced by direct laser forming. , 2006, Biomaterials.

[24]  G. Welsch,et al.  Young's modulus and damping of Ti6Al4V alloy as a function of heat treatment and oxygen concentration , 1990 .

[25]  N. Fleck,et al.  Compression fatigue of a cellular Al alloy , 1999 .

[26]  L. Murr,et al.  Compression deformation behavior of Ti-6Al-4V alloy with cellular structures fabricated by electron beam melting. , 2012, Journal of the mechanical behavior of biomedical materials.

[27]  G. Welsch,et al.  Elastic moduli and tensile and physical properties of heat-treated and quenched powder metallurgical Ti-6Al-4V alloy , 1991 .

[28]  J Kadkhodapour,et al.  Numerical simulation of the fatigue behavior of additive manufactured titanium porous lattice structures. , 2016, Materials science & engineering. C, Materials for biological applications.

[29]  L. Murr,et al.  Microstructure and mechanical properties of open-cellular biomaterials prototypes for total knee replacement implants fabricated by electron beam melting. , 2011, Journal of the mechanical behavior of biomedical materials.

[30]  W. Soboyejo,et al.  Compression–compression fatigue of open cell aluminum foams: macro-/micro- mechanisms and the effects of heat treatment , 2004 .

[31]  Abhay Pandit,et al.  Fabrication methods of porous metals for use in orthopaedic applications. , 2006, Biomaterials.

[32]  Radovan Kovacevic,et al.  Fatigue properties of a dental implant produced by electron beam melting® (EBM) , 2015 .

[33]  André Luiz Jardini,et al.  Microstructure and mechanical behavior of porous Ti-6Al-4V parts obtained by selective laser melting. , 2013, Journal of the mechanical behavior of biomedical materials.

[34]  M. Ashby,et al.  Fatigue failure of an open cell and a closed cell aluminium alloy foam , 1999 .

[35]  Mccullough,et al.  The stress–life fatigue behaviour of aluminium alloy foams , 2000 .

[36]  Emeka Nkenke,et al.  Effects of topographical surface modifications of electron beam melted Ti-6Al-4V titanium on human fetal osteoblasts. , 2008, Journal of biomedical materials research. Part A.

[37]  Brent Stucker,et al.  Influence of Defects on Mechanical Properties of Ti-6Al-4V Components Produced by Selective Laser Melting and Electron Beam Melting , 2015 .

[38]  S. M. Ahmadi,et al.  Relationship between unit cell type and porosity and the fatigue behavior of selective laser melted meta-biomaterials. , 2015, Journal of the mechanical behavior of biomedical materials.

[39]  L. Murr,et al.  Next-generation biomedical implants using additive manufacturing of complex, cellular and functional mesh arrays , 2010, Philosophical Transactions of the Royal Society A: Mathematical, Physical and Engineering Sciences.

[40]  A. A. Zadpoor,et al.  Selective laser melting‐produced porous titanium scaffolds regenerate bone in critical size cortical bone defects , 2013, Journal of orthopaedic research : official publication of the Orthopaedic Research Society.

[41]  D. Hutmacher,et al.  Scaffolds in tissue engineering bone and cartilage. , 2000, Biomaterials.