Collapse load of composite laminates: Lower bound evaluation by stress field analytical approximation

Abstract The paper proposes a limit analysis approach to define the ultimate load capacity of orthotropic composite laminates under biaxial loading and plane stress conditions. A lower bound to the collapse load multiplier is computed by solving a maximization nonlinear problem, according to the static theorem of limit analysis. To set up the optimization problem a stress field distribution is hypothesized at lamina level, moreover inter-lamina stresses are also considered. The effectiveness and validity of the proposed approach is shown by comparing the obtained numerical predictions both with available experimental data and with other numerical results carried out by means of a different numerical lower bound approach.

[1]  Haofeng Chen,et al.  Shakedown and limit analyses for 3-D structures using the linear matching method , 2001 .

[2]  Antonio Capsoni.  Limit analysis of anisotropic structures based on the kinematic theorem , 2001 .

[3]  Paolo Fuschi,et al.  Failure modes prediction of multi-pin joints FRP laminates by limit analysis , 2013 .

[4]  A. A. Pisano,et al.  Mechanically fastened joints in composite laminates: Evaluation of load bearing capacity , 2011 .

[5]  P. D. Soden,et al.  A COMPARISON OF THE PREDICTIVE CAPABILITIES OF CURRENT FAILURE THEORIES FOR COMPOSITE LAMINATES, JUDGED AGAINST EXPERIMENTAL EVIDENCE , 2002 .

[6]  P. Fuschi,et al.  A layered limit analysis of pinned-joints composite laminates: Numerical versus experimental findings , 2012 .

[7]  P. D. Soden,et al.  Biaxial test results for strength and deformation of a range of E-glass and carbon fibre reinforced composite laminates: failure exercise benchmark data , 2002 .

[8]  Donald Mackenzie,et al.  A method of estimating limit loads by iterative elastic analysis. I—Simple examples , 1992 .

[9]  Ultimate strength of pin-loaded composite laminates: A limit analysis approach , 2011 .

[10]  Pasquale Vena,et al.  Limit analysis of orthotropic plates ? ? Partial results were presented at the Plasticity '00 Sympos , 2003 .

[11]  A. Ehrlacher,et al.  Ultimate strength of free-edge composite laminates under tensile loading : A limit analysis approach , 2006 .

[12]  P. D. Soden,et al.  Failure of ±55 Degree Filament Wound Glass/Epoxy Composite Tubes under Biaxial Compression , 1998 .

[13]  X. Zhu,et al.  Development Research of Failure Theories for Thick Composite Laminates , 2011 .

[14]  Peak load prediction of multi-pin joints FRP laminates by limit analysis , 2013 .

[15]  Ugo Icardi,et al.  Assessment of Recent Theories for Predicting Failure of Composite Laminates , 2007 .

[16]  P. Fuschi,et al.  A numerical approach for limit analysis of orthotropic composite laminates , 2007 .

[17]  J. Pastor,et al.  Lower and upper numerical bounds to the off-axis strength of unidirectional fiber-reinforced composites by limit analysis methods , 1997 .

[18]  P. D. Soden,et al.  Lamina properties, lay-up configurations and loading conditions for a range of fibre-reinforced composite laminates , 1998 .

[19]  D. Weichert,et al.  Direct Methods for Limit and Shakedown Analysis of Structures: Advanced Computational Algorithms and Material Modelling , 2015 .

[20]  P. Fuschi,et al.  A FE-based limit analysis approach for concrete elements reinforced with FRP bars , 2014 .

[21]  P. D. Soden,et al.  Influence of winding angle on the strength and deformation of filament-wound composite tubes subjected to uniaxial and biaxial loads , 1993 .

[22]  K. Spiliopoulos,et al.  Direct Methods for Limit States in Structures and Materials , 2013 .

[23]  P. Soden,et al.  The effects of radial stresses on the strength of thin-walled filament wound GRP composite pressure cylinders , 1995 .

[24]  P. D. Soden,et al.  Experimental failure stresses for +55° filament wound glass fibre reinforced plastic tubes under biaxial loads , 1989 .

[25]  Paolo Fuschi,et al.  Peak loads and failure modes of steel-reinforced concrete beams: Predictions by limit analysis☆☆☆ , 2013 .

[26]  Stephen W. Tsai,et al.  A General Theory of Strength for Anisotropic Materials , 1971 .

[27]  Peter Soden.  Predicting the strength of composite laminates , 2005 .