The effect of applied load and sliding speed on the tribological properties of Nylon 6 and ultra-high-molecular-weight polyethylene

Purpose – The purpose of the study was to find the best performance polymer material to be used in railway car bogies. Design/methodology/approach – Wear tests and optical and scanning electron microscopy were used. Findings – The friction coefficients of ultra-high-molecular-weight polyethylene (UHMWPE) and Nylon 6 polymers, as opposed to AISI 4140 steel, reduced with the increment of applied loads. With the increment of sliding speed, the friction coefficient increased in both UHMWPE and Nylon 6 polymers. The specific wear rate of the UHMWPE polymer was determined to be about 10-14 m2/N, whereas the rate of Nylon 6 was determined to be 10-13 m2/N. Practical implications – The aim of the study was to find the best performance polymer material to be used in railway car bogies. Originality/value – The friction and wear performance of UHMWPE and Nylon 6 engineering polymers were studied and compared to their AISI 4140 steel counterparts. It is an original work and it is not published in any media.

[1]  A. Mimaroglu,et al.  Friction and wear behaviour of unfilled engineering thermoplastics , 2003 .

[2]  Yunhai Ma,et al.  Effects of the wollastonite fiber modification on the sliding wear behavior of the UHMWPE composites , 2003 .

[3]  Alois K. Schlarb,et al.  Morphologies of the wear debris of polyetheretherketone produced under dry sliding conditions: Correlation with wear mechanisms , 2009 .

[4]  S. E. Franklin.  Wear experiments with selected engineering polymers and polymer composites under dry reciprocating sliding conditions , 2001 .

[5]  Jayashree Bijwe,et al.  Abrasive wear performance of various polyamides , 2002 .

[6]  Yang Huayong,et al.  Tribological properties of kaolin filled UHMWPE composites in unlubricated sliding , 2004 .

[7]  A. Mimaroğlu,et al.  Evaluation of tribological behaviour of PEEK and glass fibre reinforced PEEK composite under dry sliding and water lubricated conditions , 2008 .

[8]  Li-xin Zhao,et al.  Tribological performance of nano-Al2O3 reinforced polyamide 6 composites , 2006 .

[9]  S. Bahadur.  The development of transfer layers and their role in polymer tribology , 2000 .

[10]  A. Baptista,et al.  Tribological behaviour of food grade polymers against stainless steel in dry sliding and with sugar , 2002 .

[11]  Huseyin Unal,et al.  Dry sliding wear characteristics of some industrial polymers against steel counterface , 2004 .

[12]  J. Arinez,et al.  Tribology of polyethylene homocomposites , 1998 .

[13]  A. Sarkar.  Friction and wear , 1980 .

[14]  Zhongya Zhang,et al.  Effects of various fillers on the sliding wear of polymer composites , 2005 .

[15]  Gao Jintang,et al.  Tribochemical effects in formation of polymer transfer film , 2000 .

[16]  J. Li,et al.  Sliding wear behavior and mechanism of ultra-high molecular weight polyethylene , 1999 .

[17]  B. F. Yousif,et al.  Wear and friction characteristics of CGRP composite under wet contact condition using two different test techniques , 2008 .

[18]  Tongsheng Li,et al.  Tribological behaviors of several polymer–polymer sliding combinations under dry friction and oil-lubricated conditions , 2007 .

[19]  Tribology of ultra-high molecular weight polyethylene disks molded at different temperatures , 2007 .

[20]  N. Chand,et al.  Sliding wear of PP/UHMWPE blends: effect of blend composition , 2001 .

[21]  Carlo Poggi,et al.  Influence of counterface roughness on friction properties of engineering plastics for bearing applications , 2009 .

[22]  R. Gnanamoorthy,et al.  Sliding wear performance of polyamide 6–clay nanocomposites in water , 2007 .

[23]  Taner Yilmaz,et al.  Thermal aging effects on mechanical and tribological performance of PEEK and short fiber reinforced PEEK composites , 2007 .

[24]  A. Mimaroğlu,et al.  Friction and wear performance of pure and glass fibre reinforced poly-ether-imide on polymer and steel counterface materials , 2007 .

[25]  Tongsheng Li,et al.  Morphology and microstructure of polyamide 46 wear debris and transfer film: In relation to wear mechanisms , 2008 .

[26]  Enver Atik,et al.  Tribological properties of polymer-based journal bearings , 2009 .

[27]  E. Feyzullahoğlu,et al.  The tribological behaviour of different engineering plastics under dry friction conditions , 2008 .