Mechanical and microstructural properties of heat cured alkali-activated slag mortars

The effects of steam and autoclave curing on the mechanical properties and microstructure of alkali activated slag mortars (AAS) were investigated within the scope of this study. Slag was activated by the mixtures of sodium hydroxide and sodium silicate, in different Na2O and Ms (SiO2/Na2O) ratios. Test results showed that high strength mortars can be produced with very low alkali content under autoclave curing as a result of better pore size distribution, higher rate of hydrated parts of slag grains which leads to a better microstructure formation. A compressive strength value of 70 MPa has been reached by incorporation of 2% Na2O under autoclave curing. Nevertheless, steam curing presents similar mechanical performance with autoclave curing for AAS mortar activated by the solutions with high Ms values. Both curing methods were significantly effective in terms of reducing drying shrinkage of AAS mortars.

[1]  Jay G. Sanjayan,et al.  Resistance of alkali-activated slag concrete to acid attack , 2003 .

[2]  Francisca Puertas,et al.  Pore solution in alkali-activated slag cement pastes. Relation to the composition and structure of calcium silicate hydrate , 2004 .

[3]  P. L. Pratt,et al.  Factors affecting the strength of alkali-activated slag , 1994 .

[4]  Jay G. Sanjayan,et al.  Effect of admixtures on properties of alkali-activated slag concrete , 2000 .

[5]  C. Shi,et al.  Alkali-Activated Cements and Concretes , 2003 .

[6]  J. Davidovits.  Geopolymers : inorganic polymeric new materials , 1991 .

[7]  Fernando Pacheco-Torgal,et al.  Alkali-activated binders: A review. Part 2. About materials and binders manufacture , 2008 .

[8]  A. Ramezanianpour,et al.  Effect of type, form, and dosage of activators on strength of alkali-activated natural pozzolans , 2011 .

[9]  Jay G. Sanjayan,et al.  Resistance of alkali-activated slag concrete to alkali–aggregate reaction , 2001 .

[10]  Cengiz Duran Atiş,et al.  Influence of Activator on the Strength and Drying Shrinkage of Alkali-Activated Slag Mortar , 2009 .

[11]  J. Sanjayan,et al.  Workability and mechanical properties of alkali activated slag concrete , 1999 .

[12]  Francisca Puertas,et al.  MECHANICAL AND DURABLE BEHAVIOUR OF ALKALINE CEMENT MORTARS REINFORCED WITH POLYPROPYLENE FIBRES , 2003 .

[13]  J. Sanjayan,et al.  Effect of elevated temperature curing on properties of alkali-activated slag concrete , 1999 .

[14]  Caijun Shi,et al.  Interface between cement paste and quartz sand in alkali-activated slag mortars , 1998 .

[15]  Jay G. Sanjayan,et al.  Sulfate attack on alkali-activated slag concrete , 2002 .

[16]  F. Glasser,et al.  Thermal treatment of C–S–H gel at 1 bar H2O pressure up to 200 °C , 2003 .

[17]  C. Shi,et al.  Hydration of alkali-slag cements at 150°C , 1991 .

[18]  V. Zivica,et al.  Effects of type and dosage of alkaline activator and temperature on the properties of alkali-activated slag mixtures , 2007 .

[19]  C. Shi,et al.  CEMENTITIOUS PROPERTIES OF LADLE SLAG FINES UNDER AUTOCLAVE CURING CONDITIONS , 2003 .

[20]  Jay G. Sanjayan,et al.  Resistance of alkali-activated slag concrete to carbonation , 2001 .

[21]  Wellington Longuini Repette,et al.  Drying and autogenous shrinkage of pastes and mortars with activated slag cement , 2008 .

[22]  Francisca Puertas,et al.  The alkali–silica reaction in alkali-activated granulated slag mortars with reactive aggregate , 2002 .

[23]  Jay G. Sanjayan,et al.  Alkali activation of Australian slag cements , 1999 .

[24]  Francisca Puertas,et al.  Alkali-activated slag mortars: Mechanical strength behaviour , 1999 .

[25]  L. Turanli,et al.  Pozzolanic activity of clinoptilolite: A comparative study with silica fume, fly ash and a non-zeolitic natural pozzolan , 2010 .

[26]  Shuqing Zhang,et al.  Effect of ground quartz sand on properties of high-strength concrete in the steam-autoclaved curing , 2000 .

[27]  Surendra P. Shah,et al.  Effects of curing conditions on properties of concrete using slag replacement , 2000 .

[28]  A. Neville.  Properties of Concrete , 1968 .

[29]  P. Chindaprasirt,et al.  Compressive strength, modulus of elasticity, and water permeability of inorganic polymer concrete , 2010 .