Precision fabrication techniques and analysis on high-Q evanescent-mode resonators and filters of different geometries

High-Q evanescent-mode resonators and filters are realized by both silicon micromachining and layer-by-layer polymer processing. Capacitively loaded cavities can be reduced to a size much smaller than a wavelength, but still have a much higher unloaded Q than lumped elements. The loaded resonators are utilized for reduced-size filters with a low insertion loss enabled by the relatively high-Q factor. The small fabrication tolerances of silicon micromachining and polymer stereolithography processing enable the realization of highly loaded evanescent-mode resonators and filters. A 14-GHz resonator micromachined in silicon has a volume of 5 mm /spl times/ 5 mm /spl times/ 0.45 mm, representing a resonant frequency reduction of 66.8% compared to an empty cavity of the same dimensions. The polymer-based fabrication is used to create resonators of different three-dimensional geometries with Q's up to 1940 and frequency reductions up to 49.9%. An insertion loss of 0.83 dB is measured in a 1.69% bandwidth filter created by polymer processing with a frequency reduction of 47% compared to an unloaded cavity. The frequency sensitivity to fabrication tolerances of these structures is also analyzed.

[1]  Xun Gong,et al.  Layer-by-layer polymer stereolithography fabrication for three-dimensional RF components , 2004, 2004 IEEE MTT-S International Microwave Symposium Digest (IEEE Cat. No.04CH37535).

[2]  H.-W. Yao,et al.  Quarter wavelength ceramic combline filters , 1996 .

[3]  Willy Sansen,et al.  Compensation structures for convex corner micromachining in silicon , 1990 .

[4]  Jr. R. Wyndrum.  Microwave filters, impedance-matching networks, and coupling structures , 1965 .

[5]  O. Tabata,et al.  Anisotropic etching of silicon in TMAH solutions , 1992 .

[6]  W. Ko,et al.  Compensating corner undercutting in anisotropic etching of (100) silicon , 1989 .

[7]  W.J. Chappell,et al.  Applications of layer-by-layer polymer stereolithography for three-dimensional high-frequency components , 2004, IEEE Transactions on Microwave Theory and Techniques.

[8]  L. Katehi,et al.  A vertically integrated micromachined filter , 2002 .

[9]  M. M. Abu‐Zeid,et al.  Corner Undercutting in Anisotropically Etched Isolation Contours , 1984 .

[10]  Andrew R. Brown,et al.  High-Q integrated micromachined components for a 28 GHz front-end transceiver. , 1999 .

[11]  L. Katehi,et al.  High-Q evanescent-mode filters using silicon micromachining and polymer stereolithography (SL) processing , 2004, 2004 IEEE MTT-S International Microwave Symposium Digest (IEEE Cat. No.04CH37535).

[12]  R.V. Snyder,et al.  Bandstop filter design using evanescent mode resonators , 2003, IEEE MTT-S International Microwave Symposium Digest, 2003.

[13]  A. Faes,et al.  Microstructures etched in doped TMAH solutions , 2000 .

[14]  Reinoud F. Wolffenbuttel,et al.  Effects of (110)-oriented corner compensation structures on membrane quality and convex corner integrity in (100)-silicon using aqueous KOH , 1995 .

[15]  H. Sandmaier,et al.  Fabrication of Non‐Underetched Convex Corners in Anisotropic Etching of (100)‐Silicon in Aqueous KOH with Respect to Novel Micromechanic Elements , 1990 .

[16]  Irena Zubel,et al.  Silicon anisotropic etching in alkaline solutions II on the influence of anisotropy on the smoothness of etched surfaces , 1998 .

[17]  Irena Zubel,et al.  Silicon anisotropic etching in alkaline solutions III: On the possibility of spatial structures forming in the course of Si(100) anisotropic etching in KOH and KOH+IPA solutions , 2000 .

[18]  John W. Gipprich,et al.  Low-temperature cofired ceramic (LTCC) ridge waveguide bandpass chip filters , 1999, IMS 1999.

[19]  A. A. Kirilenko,et al.  Evanescent-mode ridged waveguide bandpass filters with improved performance , 2002 .

[20]  G. Matthaei,et al.  Design of microwave filters , 2002 .

[21]  Irena Barycka,et al.  Silicon anisotropic etching in alkaline solutions IV The effect of organic and inorganic agents on silicon anisotropic etching process , 2001 .

[22]  W.J. Chappell,et al.  Multifunctional substrates for high-frequency applications , 2003, IEEE Microwave and Wireless Components Letters.

[23]  Osamu Tabata,et al.  pH-controlled TMAH Etchants For Silicon Micromachining , 1995, Proceedings of the International Solid-State Sensors and Actuators Conference - TRANSDUCERS '95.

[24]  Xun Gong,et al.  Reduced size capacitive defect EBG resonators , 2002, 2002 IEEE MTT-S International Microwave Symposium Digest (Cat. No.02CH37278).

[25]  Anders Hanneborg,et al.  Etch rates of (100), (111) and (110) single-crystal silicon in TMAH measured in situ by laser reflectance interferometry , 2000 .

[26]  Ernst Obermeier,et al.  Effect of the silicon content of aqueous KOH on the etching behaviour of convex corners in <100> single crystalline silicon , 1997, Proceedings of International Solid State Sensors and Actuators Conference (Transducers '97).

[27]  K. Bean,et al.  Anisotropic etching of silicon , 1978, IEEE Transactions on Electron Devices.

[28]  Tao Shen,et al.  Length reduction of evanescent-mode ridge waveguide bandpass filters , 2001, 2001 IEEE MTT-S International Microwave Sympsoium Digest (Cat. No.01CH37157).

[29]  Irena Barycka,et al.  Silicon anisotropic etching in alkaline solutions I. The geometric description of figures developed under etching Si(100) in various solutions , 1998 .

[30]  R. Brown,et al.  Analysis of Antipodal Ridge Waveguide Structure and Application on Extremely Wide Stopband Lowpass Filter , 1986, 1986 IEEE MTT-S International Microwave Symposium Digest.

[31]  Kawthar A. Zaki,et al.  Transitional combline/evanescent mode microwave filters , 1996, IMS 1996.

[32]  A.M.K. Saad,et al.  Novel Lowpass Harmonic Filters for Satellite Application , 1984 .

[33]  R. Brown,et al.  Evanescent Mode-Serrated Ridge Waveguide Bandpass Harmonic Filters , 1986, 1986 16th European Microwave Conference.