An Architecture for On-Line Measurement of the Tip Clearance and Time of Arrival of a Bladed Disk of an Aircraft Engine

Safety and performance of the turbo-engine in an aircraft is directly affected by the health of its blades. In recent years, several improvements to the sensors have taken place to monitor the blades in a non-intrusive way. The parameters that are usually measured are the distance between the blade tip and the casing, and the passing time at a given point. Simultaneously, several techniques have been developed that allow for the inference—from those parameters and under certain conditions—of the amplitude and frequency of the blade vibration. These measurements are carried out on engines set on a rig, before being installed in an airplane. In order to incorporate these methods during the regular operation of the engine, signal processing that allows for the monitoring of those parameters at all times should be developed. This article introduces an architecture, based on a trifurcated optic sensor and a hardware processor, that fulfills this need. The proposed architecture is scalable and allows several sensors to be simultaneously monitored at different points around a bladed disk. Furthermore, the results obtained by the electronic system will be compared with the results obtained by the validation of the optic sensor.

[1]  Fajie Duan,et al.  Analysis of the Tip-Timing Precision of Double-Shielded Capacitive Pulse Sensor , 2009, 2009 International Conference on Measuring Technology and Mechatronics Automation.

[2]  Grigorios Dimitriadis,et al.  A comparison of blade tip timing data analysis methods , 2001 .

[3]  P. Russhard.  The Rise and Fall of the Rotor Blade Strain Gauge , 2015 .

[4]  Jan R. Wright,et al.  A class of methods for the analysis of blade tip timing data from bladed assemblies undergoing simultaneous resonances - Part II: Experimental validation , 2007 .

[5]  Zhang Yong-kui,et al.  Tip clearance optical measurement for rotating blades , 2011, MSIE 2011.

[6]  Antonios Pezouvanis,et al.  Turbine Blade Vibration Measurement Methods for Turbocharges , 2014 .

[7]  N. Mrad,et al.  Aircraft Engine Blade Tip Monitoring Using Pulsed Eddy Current Technology , 2012 .

[8]  A. G. Sheard.  Blade by Blade Tip Clearance Measurement , 2011 .

[9]  Bryan Will Hayes.  Design, Implementation, and Analysis of a Time of Arrival Measurement System for Rotating Machinery , 2012 .

[10]  Georg Schröbel Weg.  Techniques for blade tip clearance measurements with capacitive probes , 2000 .

[11]  R. Rzadkowski,et al.  Tip-Timing and Tip-Clearance for Measuring Rotor Turbine Blade Vibrations , 2014 .

[12]  Romuald Rzadkowski,et al.  Analysis of middle bearing failure in rotor jet engine using tip-timing and tip-clearance techniques , 2016 .

[13]  Mark R. Woike,et al.  Testing of a Microwave Blade Tip Clearance Sensor at the NASA Glenn Research Center , 2013 .

[14]  Gotzon Aldabaldetreku,et al.  An Optical Fiber Bundle Sensor for Tip Clearance and Tip Timing Measurements in a Turbine Rig , 2013, Sensors.

[15]  V. P. Mahadevan Pillai,et al.  Fibre optic displacement sensor for the measurement of amplitude and frequency of vibration , 2007 .

[16]  Lars Büttner,et al.  Turbo machine tip clearance and vibration measurements using a fibre optic laser Doppler position sensor , 2006 .

[17]  Lim Meng Hee,et al.  Condition Monitoring of Blade in Turbomachinery: A Review , 2014 .

[18]  P. S. Heyns,et al.  A Comparison Between Three Blade Tip Timing Algorithms for Estimating Synchronous Turbomachine Blade Vibration , 2015 .

[19]  Craig Lawson,et al.  Tubomachinery blade vibration amplitude measurement through tip timing with capacitance tip clearanc , 2005 .

[20]  S. R. Turner,et al.  Electromechanical Measurement of Turbomachinery Blade Tip-to-Casing Running Clearance , 1992 .

[21]  Vítězslav Bula,et al.  Contactless Measuring Method of Blade Vibration During Turbine Speed-Up , 2010 .

[22]  Bruce M. Steinetz,et al.  Turbine Engine Clearance Control Systems: Current Practices and Future Directions , 2002 .

[23]  K. S. Chana,et al.  The Use of Eddy Current Sensors for the Measurement of Rotor Blade Tip Timing: Sensor Development and Engine Testing , 2008 .

[24]  M. Zielinski,et al.  Noncontact vibration measurements on compressor rotor blades , 2000 .

[25]  Todd Michael Pickering.  Methods for Validation of a Turbomachinery Rotor Blade Tip Timing System , 2014 .

[26]  G. Rossi,et al.  Blade Tip Clearance and Blade Vibration Measurements using a Magnetoresistive Sensor , 2015 .

[27]  W. C. Haase,et al.  Advances in through-the-case eddy current sensors , 2013, 2013 IEEE Aerospace Conference.

[28]  P. Tappert,et al.  Health monitoring and prognostics of blades and disks with blade tip sensors , 2000, 2000 IEEE Aerospace Conference. Proceedings (Cat. No.00TH8484).

[29]  Vjaceslav Georgiev,et al.  The blade flutter measurement based on the blade tip timing method , 2011 .