An Innovative Two-Stage Reheating Process for Wrought Aluminum Alloy During Thixoforming

An innovative two-stage reheating process has been developed to improve the thixotropic behavior of semi-solid wrought aluminum alloy during thixoforming. The variation of the microstructural evolution mechanisms with temperature and holding time during a traditional process and two-stage reheating process are presented in this paper. A preferred semi-solid microstructure with spherical-like grains surrounded by a uniform liquid film was obtained in the two-stage reheating process. The semi-solid microstructure obtained via this two-stage reheating process had a number of features beneficial for semi-solid metal processing, including smaller equivalent diameters, a higher degree of sphericity, a lower coarsening rate constant of solid grains and a reduced amount of entrapped liquid compared with that produced by the traditional reheating process. These results indicate that the two-stage reheating process is a promising method for manufacturing wrought aluminum alloy during thixoforming.

[1]  E. Tzimas,et al.  Evolution of near-equiaxed microstructure in the semisolid state , 2000 .

[2]  G. G. Stokes.  "J." , 1890, The New Yale Book of Quotations.

[3]  C. Kang,et al.  Coarsening of equiaxed microstructure in the semisolid state of aluminum 7075 alloy through SIMA processing , 2012, Journal of Materials Science.

[4]  M. Flemings,et al.  Characterization of the microstructure evolution of a semi-solid metal slurry during the early stages , 2012 .

[5]  D. Brabazon,et al.  Injection Tests and Effect on Microstructure and Properties of Aluminium 7075 Direct Thermal Method Feedstock Billets , 2014 .

[6]  S. Annavarapu,et al.  Inhibited coarsening of solid-liquid microstructures in spray casting at high volume fractions of solid , 1995 .

[7]  N. Haghdadi,et al.  The semisolid microstructural evolution of a severely deformed A356 aluminum alloy , 2013 .

[8]  H. Atkinson,et al.  Microstructural coarsening of 7005 aluminum alloy semisolid billets with high solid fraction , 2014 .

[9]  R. Pesci,et al.  Microstructure observation and quantification of the liquid fraction of M2 steel grade in the semi-solid state, combining confocal laser scanning microscopy and X-ray microtomography , 2014 .

[10]  Régis Bigot,et al.  Microstructure and flow behaviour during backward extrusion of semi-solid 7075 aluminium alloy , 2012 .

[11]  Z. Ji,et al.  Evolution of the semi-solid microstructure of ADC12 alloy in a modified SIMA process , 2011 .

[12]  H. Atkinson,et al.  Microstructural Coarsening of Semi-Solid Aluminium Alloys , 2008 .

[13]  Z. Fan,et al.  Semi-solid processing of engineering alloys by a twin-screw rheomoulding process , 2001 .

[14]  Qiang Chen,et al.  An investigation of microstructure evolution of RAP processed ZK60 magnesium alloy , 2009 .

[15]  A. Bolouri,et al.  Microstructural evolution during semisolid state strain induced melt activation process of aluminum 7075 alloy , 2010 .

[16]  Yi Sun,et al.  Microstructure evolution of AM60 magnesium alloy semisolid slurry prepared by new SIMA , 2010 .

[17]  H. Atkinson,et al.  Recrystallisation in the Semi-Solid State in 7075 Aluminium Alloy , 2008 .

[18]  M. Nili-Ahmadabadi,et al.  Recrystallization behavior of ECAPed A356 alloy at semi-solid reheating temperature , 2010 .

[19]  C. Kang,et al.  The effect of raw material fabrication process on microstructural characteristics in reheating process for semi-solid forming , 2005 .

[20]  H. Atkinson,et al.  Thixoforming 7075 aluminium alloys , 2005 .