Effect of Pre-deformation on Decomposition and Spheroidization of M2C Carbide in High-Speed Steel

[1]  Jianqing Jiang,et al.  Deformation-Induced Carbide Transformation in M2 High-Speed Steel , 2019, Metallurgical and Materials Transactions A.

[2]  D. Schryvers,et al.  Characterization of (Ti,Mo,Cr)C nanoprecipitates in an austenitic stainless steel on the atomic scale , 2019, Acta Materialia.

[3]  S. Zhang,et al.  Deformation-Induced Dynamic Ferrite Transformation During Hot-Rolling in Oxide Dispersion-Strengthened Ferritic Steel with 9 Wt Pct Cr Content , 2018, Metallurgical and Materials Transactions A.

[4]  B. Avishan.  Transformation induced plasticity effect under tensile and compression stresses in nanostructured bainite , 2018, Materials Science and Engineering: A.

[5]  Xia Li,et al.  Influence of original austenite grain size on tensile properties of a high-manganese transformation-induced plasticity (TRIP) steel , 2018 .

[6]  R. Misra,et al.  On the strain rate sensitivity of aluminum-containing transformation-induced plasticity steels: Interplay between TRIP and TWIP effects , 2018 .

[7]  Yang Ren,et al.  Temperature-dependent micromechanical behavior of medium-Mn transformation-induced-plasticity steel studied by in situ synchrotron X-ray diffraction , 2017 .

[8]  J. Takahashi,et al.  Direct observation of niobium segregation to dislocations in steel , 2016 .

[9]  P. Bristowe,et al.  Segregation of alloying elements to intrinsic and extrinsic stacking faults in γ′-Ni3Al via first principles calculations , 2015 .

[10]  R. Misra,et al.  Austenite stability and deformation behavior in a cold-rolled transformation-induced plasticity steel with medium manganese content , 2015 .

[11]  C. Weinberger,et al.  Elevated-temperature Deformation Mechanisms in Ta2C: An Experimental Study , 2013 .

[12]  F. Fang,et al.  Study on decomposition behaviour of M2C eutectic carbide in high speed steel , 2012 .

[13]  Tingting Liu,et al.  Phase transformation refinement of coarse primary carbides in M2 high speed steel , 2011 .

[14]  Ming Han,et al.  Variant selection and the strengthening effect of S precipitates at dislocations in Al–Cu–Mg alloy , 2011 .

[15]  Y. Chang,et al.  Kinetics of deformation induced martensitic transformation in a 304 stainless steel , 2001 .

[16]  H. Goldenstein,et al.  Solidification of high speed steels , 2001 .

[17]  Takeshi Iwamoto,et al.  Computational simulation of the dependence of the austenitic grain size on the deformation behavior of TRIP steels , 2000 .

[18]  K. Baik,et al.  Different carbide types and their effect on bend properties of a spray-formed high speed steel , 1998 .

[19]  S. Ahn,et al.  Solidification microstructure and M2C carbide decomposition in a spray-formed high-speed steel , 1998 .

[20]  R. G. Stringfellow,et al.  A constitutive model for transformation plasticity accompanying strain-induced martensitic transformations in metastable austenitic steels , 1992 .

[21]  J. Bolton,et al.  Plastic deformation mechanisms in tungsten carbide , 1980 .

[22]  Gregory B Olson,et al.  Kinetics of strain-induced martensitic nucleation , 1975 .

[23]  W. Williams,et al.  Influence of Temperature, Strain Rate, Surface Condition, and Composition on the Plasticity of Transition‐Metal Carbide Crystals , 1964 .

[24]  A. Götte,et al.  Metall , 1897 .

[25]  Jianqing Jiang,et al.  Morphology, microstructure and decomposition behavior of M2C carbides in high speed steel , 2017 .

[26]  A. Borgenstam,et al.  Deformation Microstructure and Deformation-Induced Martensite in Austenitic Fe-Cr-Ni Alloys Depending on Stacking Fault Energy , 2016, Metallurgical and Materials Transactions A.