Surface Treatment of Carbon Nanotubes Using Modified Tapioca Starch for Improved Force Detection Consistency in Smart Cementitious Materials

The remarkable mechanical properties and piezo-responses of carbon nanotubes (CNT) makes this group of nanomaterials an ideal candidate for use in smart cementitious materials to monitor forces and the corresponding structural health conditions of civil structures. However, the inconsistency in measurements is the major challenge of CNT-enabled smart cementitious materials to be widely applied for force detection. In this study, the modified tapioca starch co-polymer is introduced to surface treat the CNTs for a better dispersion of CNTs; thus, to reduce the inconsistency of force measurements of the CNTs modified smart cementitious materials. Cement mortar with bare (unmodified) CNTs (direct mixing method) and surfactant surface treated CNTs using sodium dodecyl benzenesulfonate (NaDDBS) were used as the control. The experimental results showed that when compared with samples made from bare CNTs, the samples made by modified tapioca starch co-polymer coated CNTs (CCNTs) showed higher dynamic load induced piezo-responses with significantly improved consistency and less hysteresis in the cementitious materials. When compared with the samples prepared with the surfactant method, the samples made by the developed CCNTs showed slightly increased force detection sensitivity with significantly improved consistency in piezo-response and only minor hysteresis, indicating enhanced dispersion effectiveness. The new CNT surface coating method can be scaled up easily to cater the potential industry needs for future wide application of smart cementitious materials.

[1]  S. Iijima.  Helical microtubules of graphitic carbon , 1991, Nature.

[2]  M. Sinica,et al.  The influence of carbon nanotubes on the properties of water solutions and fresh cement pastes , 2017 .

[3]  S. Yellampalli.  Carbon Nanotubes - Polymer Nanocomposites , 2011 .

[4]  Maria S. Konsta-Gdoutos,et al.  Mechanical Properties and Nanostructure of Cement-Based Materials Reinforced with Carbon Nanofibers and Polyvinyl Alcohol (PVA) Microfibers , 2010, SP-270: Advances in the Material Science of Concrete.

[5]  S. Kanel,et al.  Modified tapioca starch for iron nanoparticle dispersion in aqueous media: potential uses for environmental remediation , 2019, SN Applied Sciences.

[6]  W. D. de Heer,et al.  Carbon Nanotubes--the Route Toward Applications , 2002, Science.

[7]  Vesa Penttala,et al.  Surface decoration of carbon nanotubes and mechanical properties of cement/carbon nanotube composites , 2008 .

[8]  Leonard W. Bell,et al.  CHEMICAL ADMIXTURES FOR CONCRETE , 1999 .

[9]  Eil Kwon,et al.  Effects of CNT concentration level and water/cement ratio on the piezoresistivity of CNT/cement composites , 2012 .

[10]  Roberto Horowitz,et al.  Piezoresistive and piezoelectric MEMS strain sensors for vibration detection , 2007, SPIE Smart Structures and Materials + Nondestructive Evaluation and Health Monitoring.

[11]  Jung-Ah Han,et al.  Preparation and physical characteristics of slowly digesting modified food starches , 2007 .

[12]  Maria S. Konsta-Gdoutos,et al.  Self sensing carbon nanotube (CNT) and nanofiber (CNF) cementitious composites for real time damage assessment in smart structures , 2014 .

[13]  B. Chisholm,et al.  Iron nanoparticles coated with amphiphilic polysiloxane graft copolymers: dispersibility and contaminant treatability. , 2012, Environmental science & technology.

[14]  Sungryul Yun,et al.  Mechanical, electrical, piezoelectric and electro-active behavior of aligned multi-walled carbon nanotube/cellulose composites , 2011 .

[15]  F. Witzmann,et al.  Effects of polymer wrapping and covalent functionalization on the stability of MWCNT in aqueous dispersions. , 2011, Journal of colloid and interface science.

[16]  Arjun G. Yodh,et al.  High Weight Fraction Surfactant Solubilization of Single-Wall Carbon Nanotubes in Water , 2003 .

[17]  Heng Liang,et al.  Comparison of Hydrophilicity and Mechanical Properties of Nanocomposite Membranes with Cellulose Nanocrystals and Carbon Nanotubes. , 2017, Environmental science & technology.

[18]  R. A. Lauten,et al.  On the effect of calcium lignosulfonate on the rheology and setting time of cement paste , 2017 .

[19]  Christopher R. Bowen,et al.  Full factorial design analysis of carbon nanotube polymer-cement composites , 2012 .

[20]  Shuji Hashimoto,et al.  Accurate extraction and measurement of fine cracks from concrete block surface image , 2002, IEEE 2002 28th Annual Conference of the Industrial Electronics Society. IECON 02.

[21]  Timothy J. Fowler,et al.  Identification of Fiber-reinforced Plastic Failure Mechanisms from Acoustic Emission Data using Neural Networks , 2006 .

[22]  Xiaohua Zhao,et al.  Pressure-sensitive properties and microstructure of carbon nanotube reinforced cement composites , 2007 .

[23]  Lei Chen,et al.  The Electrical Properties and Conducting Mechanisms of Carbon Nanotube/Polymer Nanocomposites: A Review , 2010 .

[24]  Francis Gerard Collins,et al.  The influences of admixtures on the dispersion, workability, and strength of carbon nanotube-OPC paste mixtures , 2012 .

[25]  A. Eliasson,et al.  Gel formation in mixtures of hydrophobically modified potato and high amylopectin potato starch , 2005 .

[26]  S.E. Lyshevski,et al.  MEMS and NEMS - systems, devices, and structures , 2004, IEEE Electrical Insulation Magazine.

[27]  Yong‐Cheng Shi,et al.  Study of octenyl succinic anhydride-modified waxy maize starch by nuclear magnetic resonance spectroscopy , 2011 .

[28]  Raúl Fangueiro,et al.  A review on nanomaterial dispersion, microstructure, and mechanical properties of carbon nanotube and nanofiber reinforced cementitious composites , 2013 .

[29]  Rashid K. Abu Al-Rub,et al.  Distribution of Carbon Nanofibers and Nanotubes in Cementitious Composites , 2010 .

[30]  Eil Kwon,et al.  A carbon nanotube/cement composite with piezoresistive properties , 2009 .

[31]  Ardavan Yazdanbakhsh,et al.  Carbon Nano Filaments in Cementitious Materials: Some Issues on Dispersion and Interfacial Bond , 2009, SP-267: Nanotechnology of Concrete: The Next Big Thing is Small.

[32]  Xiaohua Zhao,et al.  Mechanical behavior and microstructure of cement composites incorporating surface-treated multi-walled carbon nanotubes , 2005 .

[33]  R. D. T. Filho,et al.  A review on the chemical, mechanical and microstructural characterization of carbon nanotubes-cement based composites , 2017 .

[34]  N. Ahmed,et al.  Surfactant-aided dispersion of carbon nanomaterials in aqueous solution , 2019, Physics of Fluids.

[35]  Faezeh Azhari,et al.  Cement-based sensors for structural health monitoring , 2008 .

[36]  Habeom Lee,et al.  Improved piezoresistive sensitivity and stability of CNT/cement mortar composites with low water–binder ratio , 2014 .

[37]  E. Mäder,et al.  Health monitoring in continuous glass fibre reinforced thermoplastics: Manufacturing and application of interphase sensors based on carbon nanotubes , 2010 .

[38]  P. Ajayan,et al.  Applications of Carbon Nanotubes , 2001 .

[39]  Hui Li,et al.  The influence of surfactants on the processing of multi‐walled carbon nanotubes in reinforced cement matrix composites , 2009 .

[40]  Yuris A. Dzenis,et al.  On the Possibility of Discrimination of Mixed Mode Fatigue Fracture Mechanisms in Adhesive Composite Joints by Advanced Acoustic Emission Analysis , 2002 .