Chatter suppression techniques in metal cutting

The self-excited vibration, called chatter, is one of the main limitations in metal removal processes. Chatter may spoil the surface of the part and can also cause large reduction in the life of the different components of the machine tool including the cutting tool itself. During the last 60 years, several techniques have been proposed to suppress chatter. This keynote paper presents a critical review of the different chatter suppression techniques. Process solutions with design and control approaches are compiled to provide a complete view of the available methods to stabilize the cutting process. The evolution of each technique is described remarking the most important milestones in research and the corresponding industrial application. The selection of the most appropriate technique for each specific chatter problem is also discussed considering various aspects of machining processes.

[1]  B. Balachandran,et al.  A Mechanics Based Model for Study of Dynamics of Milling Operations , 2000 .

[2]  Christian Brecher,et al.  Active compensation for portal machines , 2010, Prod. Eng..

[3]  Junz Jiunn-jyh Wang,et al.  Angle and frequency domain force models for a roughing end mill with a sinusoidal edge profile , 2003 .

[4]  Tomoki Hiramatsu,et al.  Simultaneous double-sided milling of flexible plates with high accuracy and high efficiency—Suppression of forced chatter vibration with synchronized single-tooth cutters , 2011 .

[5]  Jokin Munoa,et al.  Identification of cutting force characteristics based on chatter experiments , 2011 .

[6]  Tatsuya Mori,et al.  Suppression of regenerative chatter vibration in simultaneous double-sided milling of flexible plates by speed difference , 2010 .

[7]  S. Smith,et al.  Efficient simulation programs for chatter in milling , 1993 .

[8]  R. Sridhar,et al.  A Stability Algorithm for the General Milling Process: Contribution to Machine Tool Chatter Research—7 , 1968 .

[9]  Christian Brecher,et al.  Optimal process parameters for parallel turning operations on shared cutting surfaces , 2015 .

[10]  Yusuf Altintas,et al.  Magnetic actuator for active damping of boring bars , 2014 .

[11]  Keith A. Young,et al.  Theory of Torsional Chatter in Twist Drills: Model, Stability Analysis and Composition to Test , 2001 .

[12]  Fangyu Peng,et al.  A new approach to identifying the dynamic behavior of CNC machine tools with respect to different worktable feed speeds , 2013 .

[13]  Yusuf Altintas,et al.  Mechanics and dynamics of general milling cutters.: Part I: helical end mills , 2001 .

[14]  Jokin Munoa,et al.  Chatter suppression in ram type travelling column milling machines using a biaxial inertial actuator , 2013 .

[15]  Keith Ridgway,et al.  Modelling of the stability of variable helix end mills , 2007 .

[16]  Tamás Insperger,et al.  Full-discretization and semi-discretization for milling stability prediction: Some comments , 2010 .

[17]  Atsushi Matsubara,et al.  Vibration suppression of boring bar by piezoelectric actuators and LR circuit , 2014 .

[18]  Zoltan Dombovari,et al.  INTERACTION BETWEEN MULTIPLE MODES IN MILLING PROCESSES , 2013 .

[19]  Jon R. Pratt,et al.  Stability Prediction for Low Radial Immersion Milling , 2002 .

[20]  Lutfi Taner Tunc,et al.  Modeling and simulation of 5-axis milling processes , 2009 .

[21]  Christian Brecher,et al.  Materials in machine tool structures , 2015 .

[22]  Zichen Chen,et al.  Magnetorheological fluid-controlled boring bar for chatter suppression , 2009 .

[23]  Yusuf Altintas,et al.  Receptance coupling for end mills , 2003 .

[24]  Cornel Mihai Nicolescu,et al.  Suppressing tool chatter with novel multi-layered nanostructures of carbon based composite coatings , 2015 .

[25]  Erhan Budak,et al.  Analytical modeling of spindle-tool dynamics on machine tools using Timoshenko beam model and receptance coupling for the prediction of tool point FRF , 2006 .

[26]  Atsushi Matsubara,et al.  Design method of material removal process for minimizing workpiece displacement at cutting point , 2013 .

[27]  Jeong Hoon Ko,et al.  Chatter Stability of Plunge Milling , 2006 .

[28]  Erhan Budak,et al.  An Analytical Design Method for Milling Cutters With Nonconstant Pitch to Increase Stability, Part 2: Application , 2003 .

[29]  V. Vermel,et al.  Thin-Walled Part Machining Process Parameters Optimization based on Finite-Element Modeling of Workpiece Vibrations , 2013 .

[30]  Ryuta Sato,et al.  Spindle speed ramp-up test: A novel experimental approach for chatter stability detection , 2015 .

[31]  T. Schmitz,et al.  Enhanced damping in long slender end mills , 2006 .

[32]  John W. Sutherland,et al.  An Improved Method for Cutting Force and Surface Error Prediction in Flexible End Milling Systems , 1986 .

[33]  A. Lamikiz,et al.  Cutting force estimation in sculptured surface milling , 2004 .

[34]  Andreas Archenti,et al.  Design, Implementation and Analysis of Composite Material Dampers for Turning Operations , 2009 .

[35]  Zichen Chen,et al.  Parameter optimization of time-varying stiffness method for chatter suppression based on magnetorheological fluid-controlled boring bar , 2010 .

[36]  W. Kline,et al.  The Prediction of Surface Accuracy in End Milling , 1982 .

[37]  M. A. Mannan,et al.  Performance for End Mills Made of Different Tool Materials with Regards to Tool Life and Stability , 1986 .

[38]  I. E. Minis,et al.  A New Theoretical Approach for the Prediction of Machine Tool Chatter in Milling , 1993 .

[39]  Derek Yip-Hoi,et al.  Cutter-Workpiece Engagement Calculations by Parallel Slicing for Five-Axis Flank Milling of Jet Engine Impellers , 2008 .

[40]  Jifang Tian,et al.  Chatter Instability in Milling Systems with Flexible Rotating Spindles—A New Theoretical Approach , 2001 .

[41]  S. A. Tobias,et al.  Theory of finite amplitude machine tool instability , 1984 .

[42]  Ismail Lazoglu,et al.  Analysis of tool orientation for 5-axis ball-end milling of flexible parts , 2015 .

[43]  Gábor Stépán,et al.  Semi‐discretization method for delayed systems , 2002 .

[44]  Lin Gui,et al.  A Method for Identification of Machine-tool Dynamics under Machining☆ , 2015 .

[45]  Yusuf Altintas,et al.  Unified cutting force model for turning, boring, drilling and milling operations , 2012 .

[46]  A. Iglesias,et al.  Optimisation of face milling operations with structural chatter using a stability model based process planning methodology , 2014 .

[47]  Natarajan Shankar,et al.  Mitigation of chatter instabilities in milling by active structural control , 2001 .

[48]  L. Uriarte,et al.  Continuous workpiece speed variation (CWSV): Model based practical application to avoid chatter in grinding , 2009 .

[49]  Philip K. Chan,et al.  In-process detection and suppression of chatter in milling , 1992 .

[50]  Gábor Stépán,et al.  Stability of up-milling and down-milling, part 2: experimental verification , 2003 .

[51]  Erhan Budak,et al.  In-process tool point FRF identification under operational conditions using inverse stability solution , 2015 .

[52]  Tony L. Schmitz,et al.  Torsional and axial frequency response prediction by RCSA , 2010 .

[53]  Yusuf Altintas,et al.  End Milling Force Algorithms for CAD Systems , 1991 .

[54]  Soo Hun Lee,et al.  Programming spindle speed variation for machine tool chatter suppression , 2003 .

[55]  André Preumont,et al.  Regenerative chatter reduction by active damping control , 2007 .

[56]  Sanjiv G. Tewani,et al.  A study of cutting process stability of a boring bar with active dynamic absorber , 1995 .

[57]  Gábor Stépán,et al.  Stability Analysis of Turning With Periodic Spindle Speed Modulation Via Semidiscretization , 2004 .

[58]  Chi-Wei Lin,et al.  An integrated thermo-mechanical-dynamic model to characterize motorized machine tool spindles during very high speed rotation , 2003 .

[59]  Konrad Wegener,et al.  Optimal control for chatter mitigation in milling—Part 1: Modeling and control design , 2014 .

[60]  Carl R. Knospe,et al.  Active magnetic bearings for machining applications , 2004 .

[61]  Neil D. Sims,et al.  Analytical prediction of chatter stability for variable pitch and variable helix milling tools , 2008 .

[62]  Yasuhiro Kakinuma,et al.  Development of Fixture Devices for Thin and Compliant Workpieces , 2005 .

[63]  Mohammad R. Movahhedy,et al.  Prediction of chatter in high speed milling including gyroscopic effects , 2006 .

[64]  Brian S. Dutterer,et al.  Sacrificial Structure Preforms for Thin Part Machining , 2012 .

[65]  Tony L. Schmitz,et al.  ROTATING TOOL POINT FREQUENCY RESPONSE PREDICTION USING RCSA , 2007 .

[66]  T. Insperger,et al.  Analysis of the Influence of Mill Helix Angle on Chatter Stability , 2006 .

[67]  Nejat Olgac,et al.  Dynamics and Stability of Variable-pitch Milling , 2007 .

[68]  W. R. Winfough,et al.  Techniques for the Use of Long Slender End Mills in High-speed Milling , 1996 .

[69]  Yusuf Altintas,et al.  Analytical Stability Prediction and Design of Variable Pitch Cutters , 1998, Manufacturing Science and Engineering.

[70]  Berend Denkena,et al.  Process stabilization with an adaptronic spindle system , 2012, Prod. Eng..

[71]  Etsuo Marui,et al.  Suppression of chatter vibration of boring tools using impact dampers , 2000 .

[72]  Jiri Tlusty,et al.  Effect of low-friction guideways and lead-screw flexibility on dynamics of high-speed machines , 1995 .

[73]  Christian Brecher,et al.  Virtual machine tool , 2005 .

[74]  Philippe Lorong,et al.  Variable Compliance-related Aspects of Chatter in Turning Thin-walled Tubular Parts , 2015 .

[75]  D. Barrenetxea,et al.  Semi-discretization for stability analysis of in-feed cylindrical grinding with continuous workpiece speed variation , 2013 .

[76]  Erhan Budak,et al.  A closed-form approach for identification of dynamical contact parameters in spindle–holder–tool assemblies , 2009 .

[77]  Jacques Peters,et al.  Comparative assessment of harmonic, random, swept sine and shock excitation methods for the identification of machine tool structures with rotating spindles , 1975 .

[78]  Giacomo Bianchi,et al.  Active spindle system for a rotary planing machine , 2012 .

[79]  F. W. Taylor.  The Art of Cutting Metals , 1907 .

[80]  Yusuf Altintas,et al.  A novel magnetic actuator design for active damping of machining tools , 2014 .

[81]  Yunn-Shiuan Liao,et al.  A new on-line spindle speed regulation strategy for chatter control , 1996 .

[82]  Neil D. Sims,et al.  Optimisation of variable helix end millings tools by minimising self excited vibration , 2009 .

[83]  Berend Denkena,et al.  Stable islands in the stability chart of milling processes due to unequal tooth pitch , 2011 .

[84]  Yusuf Altintas,et al.  Chatter Stability of General Turning Operations With Process Damping , 2009 .

[85]  Erhan Budak,et al.  Optimization of Serrated End Mills for Reduced Cutting Energy and Higher Stability , 2013 .

[86]  Yasuhiro Kakinuma,et al.  Active chatter suppression in turning by band-limited force control , 2014 .

[87]  Yusuf Altintas,et al.  Virtual Five-Axis Flank Milling of Jet Engine Impellers—Part I: Mechanics of Five-Axis Flank Milling , 2008 .

[88]  Fathy Ismail,et al.  Analytical stability lobes including nonlinear process damping effect on machining chatter , 2011 .

[89]  Jokin Munoa,et al.  Coupled model for simulating active inertial actuators in milling processes , 2015 .

[90]  G. Stépán,et al.  Stability of the milling process , 2000 .

[91]  Zoltan Dombovari,et al.  On the bistable zone of milling processes , 2015, Philosophical Transactions of the Royal Society A: Mathematical, Physical and Engineering Sciences.

[92]  Fathy Ismail,et al.  A new method for the identification of stability lobes in machining , 1997 .

[93]  Toshio Sata,et al.  Stability Analysis of Cutting under Varying Spindle Speed , 1977 .

[94]  Fumio Obata,et al.  Active Chatter Suppression of Slender Boring Bar Using Piezoelectric Actuators , 1994 .

[95]  Erdem Ozturk,et al.  Stability and high performance machining conditions in simultaneous milling , 2013 .

[96]  Chris L. Pettit,et al.  Uncertainties and dynamic problems of bolted joints and other fasteners , 2005 .

[97]  S. Smith,et al.  Stabilizing chatter by automatic spindle speed regulation , 1992 .

[98]  Yusuf Altintas,et al.  Analytical Prediction of Stability Lobes in Milling , 1995 .

[99]  D. Barrenetxea,et al.  Effectiveness of continuous workpiece speed variation (CWSV) for chatter avoidance in throughfeed centerless grinding , 2011 .

[100]  Gábor Stépán,et al.  Stability of up-milling and down-milling, part 1: alternative analytical methods , 2003 .

[101]  Hongqi Li,et al.  Analysis of bearing configuration effects on high speed spindles using an integrated dynamic thermo-mechanical spindle model , 2004 .

[102]  Neil D. Sims,et al.  Vibration Control Strategies for Proof-mass Actuators , 2007 .

[103]  Alpay Yilmaz,et al.  Machine-Tool Chatter Suppression by Multi-Level Random Spindle Speed Variation , 1999, Manufacturing Science and Engineering.

[104]  Krzysztof J. Kaliński,et al.  Optimal spindle speed determination for vibration reduction during ball-end milling of flexible details , 2015 .

[105]  Andreas Otto,et al.  Frequency domain stability analysis of milling processes with variable helix tools , 2012 .

[106]  B. Mann,et al.  Stability of Interrupted Cutting by Temporal Finite Element Analysis , 2003 .

[107]  L. N. López de Lacalle Marcaide,et al.  Use of Magnetorheological Fluids for Vibration Reduction on the Milling of Thin Floor Parts , 2013 .

[108]  Jokin Munoa,et al.  Stability of milling processes with continuous spindle speed variation: Analysis in the frequency and time domains, and experimental correlation , 2008 .

[109]  Jon R. Pratt,et al.  The Stability of Low Radial Immersion Milling , 2000 .

[110]  Christian Brecher,et al.  Holistic modelling of process machine interactions in parallel milling , 2011 .

[111]  Neil D. Sims,et al.  Optimisation of variable helix tool geometry for regenerative chatter mitigation , 2011 .

[112]  Gábor Stépán,et al.  Stability of time-periodic and delayed systems - a route to act-and-wait control , 2006, Annu. Rev. Control..

[113]  Yusuf Altintas,et al.  Identification of Machining Process Damping Using Output-Only Modal Analysis , 2014 .

[114]  P. Vanherck,et al.  INCREASING MILLING MACHINE PRODUCTIVITY BY USE OF CUTTERS WITH NON-CONSTANT CUTTING-EDGE PITCH , 1968 .

[115]  Doruk Sūkrū Merdol,et al.  Virtual three-axis milling process simulation and optimization , 2008 .

[116]  Gilles Dessein,et al.  On the stability of high-speed milling with spindle speed variation , 2010 .

[117]  Krzysztof Jemielniak,et al.  Suppression of self-excited vibration by the spindle speed variation method , 1984 .

[118]  Tony L. Schmitz,et al.  Tool Point Frequency Response Prediction for High-Speed Machining by RCSA , 2001 .

[119]  Ma Yingchao,et al.  Generalized method for the analysis of bending, torsional and axial receptances of tool–holder–spindle assembly , 2015 .

[120]  Richard E. DeVor,et al.  Floquet Theory Based Approach for Stability Analysis of the Variable Speed Face-Milling Process , 2002 .

[121]  Erdem Ozturk,et al.  Dynamics and stability of parallel turning operations , 2011 .

[122]  A. Etxebarria,et al.  Hardware-in-the-loop simulator for stability study in orthogonal cutting , 2015 .

[123]  J. Tlusty,et al.  Active Damping of Structural Modes in High-Speed Machine Tools , 1997 .

[124]  Adib A. Becker,et al.  A solution for minimising vibrations in milling of thin walled casings by applying dampers to workpiece surface , 2013 .

[125]  M. Siddhpura,et al.  A review of chatter vibration research in turning , 2012 .

[126]  Ali H. Nayfeh,et al.  Chatter control and stability analysis of a cantilever boring bar under regenerative cutting conditions , 2001, Philosophical Transactions of the Royal Society of London. Series A: Mathematical, Physical and Engineering Sciences.

[127]  Sam Turner,et al.  The role of tool geometry in process damped milling , 2010 .

[128]  Yusuf Altintas,et al.  Dynamic peripheral milling of flexible structures , 1992 .

[129]  Eric A. Butcher,et al.  Analysis of Milling Stability by the Chebyshev Collocation Method: Algorithm and Optimal Stable Immersion Levels , 2009 .

[130]  Christian Brecher,et al.  Machine tool spindle units , 2010 .

[131]  A. Milecki,et al.  Investigation and control of magneto–rheological fluid dampers , 2001 .

[132]  Svetan Ratchev,et al.  Active fixturing: literature review and future research directions , 2013 .

[133]  Tibor Szalay,et al.  Real-Time Cutting Force Prediction and Cutting Force Coefficient Determination during Machining Processes , 2011 .

[134]  T. Insperger,et al.  Unstable Islands in the Stability Chart of Milling Processes Due to the Helix Angle , 2006 .

[135]  Brian P. Mann,et al.  Uncharted islands of chatter instability in milling , 2008 .

[136]  L. Taner Tunç,et al.  Prediction of workpiece dynamics and its effects on chatter stability in milling , 2012 .

[137]  S. Smith,et al.  Use of Audio Signals for Chatter Detection and Control , 1992 .

[138]  Tony L. Schmitz,et al.  Improving High-Speed Machining Material Removal Rates by Rapid Dynamic Analysis , 2001 .

[139]  Jokin Munoa,et al.  Receptance coupling for tool point dynamic prediction by fixed boundaries approach , 2014 .

[140]  Gábor Stépán,et al.  Lobes and Lenses in the Stability Chart of Interrupted Turning , 2006 .

[141]  Herbert Schulz,et al.  The history of high-speed machining , 1999 .

[142]  Francisco J. Campa,et al.  Chatter avoidance in the milling of thin floors with bull-nose end mills: Model and stability diagrams , 2011 .

[143]  Matti Rantatalo,et al.  Milling machine spindle analysis using FEM and non-contact spindle excitation and response measurement , 2007 .

[144]  Tamás Insperger,et al.  Analysis of directional factors in milling: importance of multi-frequency calculation and of the inclusion of the effect of the helix angle , 2010 .

[145]  W B Ferry,et al.  ジェット機関インペラの仮想5軸フランクミル加工‐1:5軸フランクミル加工の機械力学 , 2008 .

[146]  Zoltan Dombovari,et al.  The effect of serration on mechanics and stability of milling cutters , 2010 .

[147]  S. M. Pandit,et al.  A New Approach to the Analysis of Machine-Tool System Stability Under Working Conditions , 1977 .

[148]  Erhan Budak,et al.  Improving Productivity and Part Quality in Milling of Titanium Based Impellers by Chatter Suppression and Force Control , 2000 .

[149]  Yusuf Altintas,et al.  Multi frequency solution of chatter stability for low immersion milling , 2004 .

[150]  Charles R. Farrar,et al.  The use of active materials for machining processes : A review , 2007 .

[151]  Eberhard Abele,et al.  Creating Stability Lobe Diagrams during Milling , 2004 .

[152]  E.J.A. Armarego,et al.  Computer Based Modelling of Popular Machining Operations for Force and Power Prediction , 1985 .

[153]  Firas A. Khasawneh,et al.  A spectral element approach for the stability of delay systems , 2011 .

[154]  Gábor Stépán,et al.  On stability prediction for milling , 2005 .

[155]  Yangsheng Xu,et al.  Mapping a Space Manipulator to a Dynamically Equivalent Manipulator , 1998 .

[156]  Jiri Tlusty,et al.  Applying High-Speed Machining Techniques On Rotor Grip Configurations , 1999 .

[157]  Yiqing Yang,et al.  Milling vibration attenuation by eddy current damping , 2015 .

[158]  S. M. Pandit,et al.  A Stochastic Approach to Characterization of Machine Tool System Dynamics Under Actual Working Conditions , 1976 .

[159]  Arkadiusz Parus,et al.  Active vibration control in milling flexible workpieces , 2013 .

[160]  Yusuf Altintas,et al.  Generalized modeling of drilling vibrations. Part II: Chatter stability in frequency domain , 2007 .

[161]  Tojiro Aoyama,et al.  Application of Electrorheological Fluid Dampers to Machine Tool Elements , 1997 .

[162]  Yusuf Altintas,et al.  Identification of dynamic cutting force coefficients and chatter stability with process damping , 2008 .

[163]  Gilles Dessein,et al.  Integration of dynamic behaviour variations in the stability lobes method: 3D lobes construction and application to thin-walled structure milling , 2006 .

[164]  G. L. Xiong,et al.  Study of the gyroscopic effect of the spindle on the stability characteristics of the milling system , 2003 .

[165]  Kornel Ehmann,et al.  Machining Process Modeling: A Review , 1997 .

[166]  A. Galip Ulsoy,et al.  Nonlinear Feed Effect in Machining Chatter Analysis , 2008 .

[167]  Tony L. Schmitz,et al.  Shrink fit tool holder connection stiffness/damping modeling for frequency response prediction in milling , 2007 .

[168]  Cornel Mihai Nicolescu,et al.  Active vibration control in palletised workholding system for milling , 2006 .

[169]  Yusuf Altintas,et al.  Generalized dynamic model of metal cutting operations , 2013 .

[170]  Keith A. Young,et al.  Piezoelectric sensors and actuators for milling tool stability lobes , 2005 .

[171]  Erhan Budak,et al.  An analytical design method for milling cutters with nonconstant pitch to increase stability, Part I: Theory , 2003 .

[172]  Eugene I. Rivin,et al.  Stiffness and Damping in Mechanical Design , 1999 .

[173]  Zoltan Dombovari,et al.  Stability analysis of milling with irregular pitch tools by the implicit subspace iteration method , 2014 .

[174]  Berend Denkena,et al.  Experimental investigation and simulation of machining thin-walled workpieces , 2007, Prod. Eng..

[175]  Hisayoshi Sato,et al.  Behavior of Self-Excited Chatter Due to Multiple Regenerative Effect , 1981 .

[176]  Jacques Peters,et al.  Additive damping treatments for mechanical structures , 1981 .

[177]  S. M. Wu,et al.  Computer Design of a Vibration-Free Face-Milling Cutter , 1975 .

[178]  Guillem Quintana,et al.  Chatter in machining processes: A review , 2011 .

[179]  T.-R. Lin.  Cutting Behaviour Using Variable Feed and Variable Speed when Drilling Stainless Steel with TiN-Coated Carbide Drills , 2002 .

[180]  L. N. López de Lacalle,et al.  An automatic spindle speed selection strategy to obtain stability in high-speed milling , 2009 .

[181]  Y. S. Tarng,et al.  Design of a dynamic vibration absorber against vibrations in turning operations , 2001 .

[182]  K. Seto,et al.  Effect of a Variable Stiffness-Type Dynamic Absorber on Improving the Performance of Machine-Tools with a Long Overhung Ram , 1978 .

[183]  A. Preumont.  Vibration Control of Active Structures , 1997 .

[184]  Francisco J. Campa,et al.  An integrated process–machine approach for designing productive and lightweight milling machines , 2011 .

[185]  Rifat Sipahi,et al.  A Unique Methodology for Chatter Stability Mapping in Simultaneous Machining , 2005 .

[186]  I. Inasaki,et al.  Grinding Chatter – Origin and Suppression , 2001 .

[187]  Samir A. Nayfeh,et al.  The Two-Degree-of-Freedom Tuned-Mass Damper for Suppression of Single-Mode Vibration Under Random and Harmonic Excitation , 2006 .

[188]  Holger Hanselka,et al.  Development and design of an active work piece holder driven by piezo actuators , 2008, Prod. Eng..

[189]  S. Bolsunovsky,et al.  Reduction of Flexible Workpiece Vibrations with Dynamic Support Realized as Tuned Mass Damper , 2013 .

[190]  Peter Eberhard,et al.  Adaptronic Vibration Damping for Machine Tools , 2007 .

[191]  Tetsutaro Hoshi,et al.  Stabilization of high frequency chatter vibration in fine boring by friction damper , 2001 .

[192]  Yusuf Altintas,et al.  Modeling and avoidance of static form errors in peripheral milling of plates , 1995 .

[193]  Christian Brecher,et al.  Electrohydraulic Active Damping System , 2005 .

[194]  Pankaj Wahi,et al.  Galerkin Projections for Delay Differential Equations , 2003 .

[195]  Francisco J. Campa,et al.  Stability limits of milling considering the flexibility of the workpiece and the machine , 2005 .

[196]  T. Hoshi,et al.  Suppression of Machine-Tool Chatter by State Feedback Control , 1988 .

[197]  Berend Denkena,et al.  Virtual process systems for part machining operations , 2014 .

[198]  Manfred Weck,et al.  Chatter Stability of Metal Cutting and Grinding , 2004 .

[199]  J. Tlusty,et al.  Basic Non-Linearity in Machining Chatter , 1981 .

[200]  Nathan van de Wouw,et al.  Robust Active Chatter Control in the High-Speed Milling Process , 2012, IEEE Transactions on Control Systems Technology.

[201]  E.J.A. Armarego,et al.  Computerized Predictive Cutting Models for Forces in End-Milling Including Eccentricity Effects , 1989 .

[202]  H. Opitz,et al.  DETERMINATION OF THE TRANSFER FUNCTION BY MEANS OF SPECTRAL DENSITY MEASUREMENTS AND ITS APPLICATION TO THE DYNAMIC INVESTIGATION OF MACHINE TOOLS UNDER MACHINING CONDITIONS , 1970 .

[203]  Steven Y. Liang,et al.  Chatter stability of a slender cutting tool in turning with tool wear effect , 1998 .

[204]  Gábor Stépán,et al.  Modelling nonlinear regenerative effects in metal cutting , 2001, Philosophical Transactions of the Royal Society of London. Series A: Mathematical, Physical and Engineering Sciences.

[205]  Min Wang,et al.  On-line chatter detection and control in boring based on an electrorheological fluid , 2001 .

[206]  Lutfi Taner Tunc,et al.  Identification and modeling of process damping in turning and milling using a new approach , 2010 .

[207]  Christian Brecher,et al.  Damping models for machine tool components of linear axes , 2013 .

[208]  Jokin Munoa,et al.  Application of continuous spindle speed variation for chatter avoidance in roughing milling , 2011 .

[209]  Pascal Ray,et al.  Stability-based spindle speed control during flexible workpiece high-speed milling , 2008 .

[210]  H. K. Tönshoff,et al.  About Damping Mechanisms for Disk Shaped Tools , 1981 .

[211]  John C. Ziegert,et al.  Numerical analysis and parameter study of a mechanical damper for use in long slender endmills , 2006 .

[212]  Erhan Budak,et al.  Investigating Dynamics of Machine Tool Spindles under Operational Conditions , 2011 .

[213]  Zhengjia He,et al.  Chatter stability of milling with speed-varying dynamics of spindles , 2012 .

[214]  S. A. Tobias.  Machine-tool vibration , 1965 .

[215]  Bin Li,et al.  Estimation of FRFs of machine tools in output-only modal analysis , 2015 .

[216]  Yusuf Altintas,et al.  Optimization of multiple tuned mass dampers to suppress machine tool chatter , 2010 .

[217]  Alex Iglesias,et al.  FRF Estimation through Sweep Milling Force Excitation (SMFE) , 2016 .

[218]  Berend Denkena,et al.  Mechatronic Systems for Machine Tools , 2007 .

[219]  Youlun Xiong,et al.  A novel approach to fixture design on suppressing machining vibration of flexible workpiece , 2012 .

[220]  H. Benaroya,et al.  DYNAMICS OF TRANSVERSELY VIBRATING BEAMS USING FOUR ENGINEERING THEORIES , 1999 .

[221]  Yusuf Altintas,et al.  Modeling and identification of tool holder–spindle interface dynamics , 2007 .

[222]  Jokin Munoa,et al.  Chatter suppression in a high speed magnetic spindle by adding damping , 2014 .

[223]  D. Barrenetxea,et al.  Redesign of an active system of vibration control in a centerless grinding machine: Numerical simulation and practical implementation , 2013 .

[224]  Tobias Surmann,et al.  Simulation of milling tool vibration trajectories along changing engagement conditions , 2007 .

[225]  Christian Brecher,et al.  Machine tool feed drives , 2011 .

[226]  Z. Hadas,et al.  Using of simulation modelling for developing of active damping system , 2012, International Symposium on Power Electronics Power Electronics, Electrical Drives, Automation and Motion.

[227]  Tsu-Chin Tsao,et al.  Stability of Turning Processes with Actively Controlled Linear Motor Feed Drives , 1994 .

[228]  Yusuf Altintas,et al.  Prediction of Milling Force Coefficients From Orthogonal Cutting Data , 1996 .

[229]  Yii-Wen Hwang,et al.  Centrifugal force induced dynamics of a motorized high-speed spindle , 2006 .

[230]  Fukuo Hashimoto,et al.  Diagram for Selecting Chatter Free Conditions of Centerless Grinding , 1982 .

[231]  André Preumont,et al.  Active Damping of Chatter in Machine Tools - Demonstration with a ‘Hardware-in-the-Loop’ Simulator , 2005 .

[232]  Neil D. Sims,et al.  Milling workpiece chatter avoidance using piezoelectric active damping: a feasibility study , 2005 .

[233]  Gábor Stépán,et al.  Updated semi‐discretization method for periodic delay‐differential equations with discrete delay , 2004 .

[234]  Victor Songmene,et al.  Estimation of machine-tool dynamic parameters during machining operation through operational modal analysis , 2009 .

[235]  Gábor Stépán,et al.  Improved prediction of stability lobes with extended multi frequency solution , 2013 .

[236]  Dirk Biermann,et al.  The effect of tool vibrations on the flank surface created by peripheral milling , 2008 .

[237]  S. A. Jensen,et al.  Stability Analysis in Face Milling Operations, Part 1: Theory of Stability Lobe Prediction , 1999 .

[238]  Sébastien Seguy,et al.  Chatter milling modeling of active magnetic bearing spindle in high-speed domain , 2011 .

[239]  J. Slavíček,et al.  The Effect of Irregular Tooth Pitch on Stability of Milling , 1965 .

[240]  Aitor Olarra,et al.  Design of self-tuneable mass damper for modular fixturing systems , 2016 .

[241]  S. A. Jensen,et al.  Stability Analysis in Face Milling Operations, Part 2: Experimental Validation and Influencing Factors , 1999 .

[242]  Yusuf Altintas,et al.  Analytical Prediction of Chatter Stability in Milling—Part I: General Formulation , 1998 .

[243]  Yusuf Altintas,et al.  Mechanics and Dynamics of Serrated Cylindrical and Tapered End Mills , 2004 .

[244]  Eugene Rivin,et al.  Enhancement of dynamic stability of cantilever tooling structures , 1992 .

[245]  Alex Iglesias,et al.  Active suppression of structural chatter vibrations using machine drives and accelerometers , 2015 .

[246]  Deqing Mei,et al.  Chatter suppression by parametric excitation: Model and experiments , 2011 .

[247]  I. E. Minis,et al.  Improved Methods for the Prediction of Chatter in Turning , 1990 .

[248]  Eiji Shamoto,et al.  Analytical prediction of contact stiffness and friction damping in bolted connection , 2014 .

[249]  Han Ding,et al.  A full-discretization method for prediction of milling stability , 2010 .

[250]  Bin Li,et al.  Estimation of CNC machine–tool dynamic parameters based on random cutting excitation through operational modal analysis , 2013 .

[251]  Richard E. DeVor,et al.  Analytical Stability Analysis of Variable Spindle Speed Machining , 2000 .

[252]  L. T. Tunc,et al.  Identification and Modeling of Process Damping in Milling , 2013 .

[253]  Erhan Budak,et al.  Analytical Prediction of Part Dynamics for Machining Stability Analysis , 2010, Int. J. Autom. Technol..

[254]  Yue Wu,et al.  Model predictive control to mitigate chatters in milling processes with input constraints , 2015 .

[255]  Etsuo Marui,et al.  Plate insertion as a means to improve the damping capacity of a cutting tool system , 1998 .

[256]  Rainer Nordmann,et al.  Comparison of Control Strategies for Active Vibration Control of Flexible Structures , 2003 .

[257]  Dai Gil Lee,et al.  Manufacturing and Testing of Chatter Free Boring Bars , 1987 .

[258]  Martin Hosek,et al.  A new perspective and analysis for regenerative machine tool chatter , 1998 .

[259]  H. E. Merritt.  Theory of Self-Excited Machine-Tool Chatter: Contribution to Machine-Tool Chatter Research—1 , 1965 .

[260]  Eberhard Abele,et al.  Electromagnetic actuator for in process non-contact identification of spindle-tool frequency response functions , 2006 .

[261]  Erdem Ozturk,et al.  Tuning of tool dynamics for increased stability of parallel (simultaneous) turning processes , 2016 .

[262]  Bin Li,et al.  An approach for measuring the FRF of machine tool structure without knowing any input force , 2014 .

[263]  Jokin Munoa,et al.  Cylindrical milling tools: Comparative real case study for process stability , 2014 .

[264]  Min Wang,et al.  Chatter suppression based on nonlinear vibration characteristic of electrorheological fluids , 1999 .

[265]  Daisuke Kono,et al.  Evaluation of dynamic stiffness of machine tool spindle by non-contact excitation tests , 2015 .

[266]  C. P. Vyasarayani,et al.  Galerkin Approximations for Stability of Delay Differential Equations With Time Periodic Delays , 2015 .

[267]  F. Koenigsberger,et al.  Machine Tool Structures , 1969 .

[268]  Zoltan Dombovari,et al.  Chatter stability of milling in frequency and discrete time domain , 2008 .

[269]  Neil D. Sims,et al.  Vibration absorbers for chatter suppression: A new analytical tuning methodology , 2007 .

[270]  Berend Denkena,et al.  TOOL ADAPTOR FOR ACTIVE VIBRATION CONTROL IN TURNING OPERATIONS , 2004 .

[271]  Tony L. Schmitz,et al.  Predicting High-Speed Machining Dynamics by Substructure Analysis , 2000 .

[272]  Lutfi Taner Tunc,et al.  Effect of cutting conditions and tool geometry on process damping in machining , 2012 .

[273]  Keith Ridgway,et al.  Particle Dampers for Workpiece Chatter Mitigation , 2005 .

[274]  Cornel Mihai Nicolescu,et al.  Design and implementation of tuned viscoelastic dampers for vibration control in milling , 2008 .

[275]  Dirk Biermann,et al.  A general approach to simulating workpiece vibrations during five-axis milling of turbine blades , 2010 .

[276]  Christian Brecher,et al.  Chatter suppression with an active workpiece holder , 2010, Prod. Eng..

[277]  Hidehiko Takeyama,et al.  Improvement of Dynamic Rigidity of Tool Holder by Applying High-Damping Material , 1982 .

[278]  S. Smith,et al.  Current Trends in High-Speed Machining , 1997 .