Liquid piston gas compression

A liquid piston concept is proposed to improve the efficiency of gas compression and expansion. Because a liquid can conform to an irregular chamber volume, the surface area to volume ratio in the gas chamber can be maximized using a liquid piston. This creates near-isothermal operation, which minimizes energy lost to heat generation. A liquid piston eliminates gas leakage and replaces sliding seal friction with viscous friction. The liquid can also be used as a medium to carry heat into and out of the compression chamber. A simulation is presented of the heat transfer and frictional forces for a reciprocating piston and a liquid piston. In the application of an air compressor, with a pressure ratio of 9.5:1 and a cycle frequency of 20Â Hz, the liquid piston decreased the energy consumption by 19% over the reciprocating piston. The liquid piston and the reciprocating piston exhibited a total efficiency of 83% and 70% respectively. The liquid piston demonstrated significant improvements in the total compression efficiency in comparison to a conventional reciprocating piston. This gain in efficiency was accomplished through increasing the heat transfer during the gas compression by increasing the surface area to volume ratio in the compression chamber.

[1]  이정호,et al.  Fundamentals of Fluid Mechanics, 6th Edition , 2009 .

[2]  W. J. D. Annand,et al.  Heat Transfer in the Cylinder of a Motored Reciprocating Engine , 1980 .

[3]  Ozgen Akalin,et al.  Piston Ring-Cylinder Bore Friction Modeling in Mixed Lubrication Regime: Part I—Analytical Results , 2001 .

[4]  Robert L. Norton,et al.  Machine Design: An Integrated Approach , 1996 .

[5]  Perry Y. Li,et al.  Open Accumulator Concept for Compact Fluid Power Energy Storage , 2007 .

[6]  Ma Guoyuan,et al.  Dynamic Behavior of Twin-Piece Vane Machine , 2002 .

[7]  Herbert A. Humphrey.  An Internal-Combustion Pump, and other Applications of a New Principle , 1909 .

[8]  S. Lemofouet,et al.  Hybrid energy storage systems based on compressed air and supercapacitors with maximum efficiency point tracking , 2005, 2005 European Conference on Power Electronics and Applications.

[9]  K. J. Chun,et al.  Leakage characteristics of non-contact seal types for high-speed spindles , 2000 .

[10]  Y. Çengel.  Heat Transfer: A Practical Approach , 1997 .

[11]  B. Hamrock,et al.  Fundamentals of Fluid Film Lubrication , 1994 .

[12]  Jan Vimmr.  Mathematical modelling of compressible inviscid fluid flow through a sealing gap in the screw compressor , 2003, Math. Comput. Simul..

[13]  James E. Braun,et al.  Modeling of Hermetic Scroll Compressors: Model Development , 2004 .

[14]  Alan Abram Kornhauser,et al.  Gas-wall heat transfer during compression and expansion , 1989 .

[15]  Rogerio P. Klüppel,et al.  Thermodynamic cycle of a liquid piston pump , 1998 .

[16]  J. Gerstmann,et al.  Isothermalization of stirling heat-actuated heat pumps using liquid pistons , 1986 .

[17]  Z. Z. Yu,et al.  Study of the Piston System Structure of Advantageous to Low Friction and Economizing Energy , 2006 .

[18]  John B. Heywood,et al.  Internal combustion engine fundamentals , 1988 .

[19]  C. D. West.  Liquid piston Stirling engines , 1983 .

[20]  M F Bardon,et al.  Convective Heat Transfer in Reciprocating Engines , 1985 .

[21]  Guido Belforte,et al.  Optimization of the Cross Section of an Elastomeric Seal for Pneumatic Cylinders , 2006 .